提高实验室管理体系运行水平的探讨

本文从管理要求与技术要求两个方面指出了实验室管理体系运行中常见的问题,并结合实际情况提出了相应措施,最后对加强实验室管理体系运行有效性提出了几点建议。     

Effect of martensitic transformation in Ti–15 at %V β-phase particles on lamellar boundary decohesion in γ-TiAl Part II Finite element analysis of crack-bridging phenomenon

The commercial finite element package ABAQUS has been used to analyse the crack bridging process by Ti-15 at%V -phase particles dispersed in -TiAl matrix in the presence of particle–matrix decohesion. Both the particle–matrix decohesion potential and the -phase materials constitutive relations are found to have a major effect on the ductility, fracture toughness and failure mode of the – two-phase material. The interface potential is found to primarily affect the distribution of the normal interface strength ahead of the advancing interfacial crack and the mode (gradual versus sudden) of decohesion. The -phase materials constitutive relations are found to influence the location of nucleation of the interfacial cracks and, in turn, the mode of decohesion. A metastable -phase that can plastically deform at low stress levels by undergoing a stress-assisted martensitic transformation, but experience a high rate of strain hardening is found to give rise to the largest levels of ductility and fracture toughness is the – two-phase material. © 1998 Kluwer Academic Publishers     

Constructing the nearly shortest path in crossed cubes

A graph G is panconnected if each pair of distinct vertices u,v∈V(G) are joined by a path of length l for all d_G(u,v)?l?|V(G)|-1, where d_G(u,v) is the length of a shortest path joining u and v in G. Recently, Fan et. al. [J. Fan, X. Lin, X. Jia, Optimal path embedding in crossed cubes, IEEE Trans. Parall. Distrib. Syst. 16 (2) (2005) 1190-1200, J. Fan, X. Jia, X. Lin, Complete path embeddings in crossed cubes, Inform. Sci. 176 (22) (2006) 3332-3346] and Xu et. al. [J.M. Xu, M.J. Ma, M. Lu, Paths in Möbius cubes and crossed cubes, Inform. Proc. Lett. 97 (3) (2006) 94-97] both proved that n-dimensional crossed cube, CQ_n, is almost panconnected except the path of length d_CQn(u,v)+1 for any two distinct vertices u,v∈V(CQ_n). In this paper, we give a necessary and sufficient condition to check for the existence of paths of length d_CQn(u,v)+1, called the nearly shortest paths, for any two distinct vertices u,v in CQ_n. Moreover, we observe that only some pair of vertices have no nearly shortest path and we give a construction scheme for the nearly shortest path if it exists.     

汽车电动助力转向器的控制器研制

研究了日本N4样机的电动助力转向系统的电机电流-输入扭矩特性.采用ATmega16L单片机为处理器,以直流有刷电机为执行器,应用PID补偿算法,设计了电动助力转向控制器.在试验台上进行了电机电流-输入扭矩特性试验,试验结果表明,该控制器的助力曲线接近日本N4样机,能取得比较满意的助力效果.     

Efficient identity-based online/offline encryption and signcryption with short ciphertext

The technique of online/offline is regarded as a promising approach to speed up the computation of encryption, because the most part of computation, such as pairing over points on elliptic curve and exponentiation in groups, can be pre-computed in the offline phase without knowing the message to be encrypted and/or recipient’s identity. The online phase only requires light computation, such as modular multiplication. In this paper, we propose two novel identity-based online/offline schemes: a full secure identity-based online/offline encryption scheme and an identity-based online/offline signcryption scheme. Compared to the other schemes in the literature, our schemes achieve the shortest ciphertext size in both offline and online phases and demonstrate the best performance in offline computation. Our schemes are applicable to devices with limited computation power. They are proven secure in the random oracle model.     

Functionally testable path delay faults on a microprocessor

The impact of delay defects on these functionally untestable paths on overall circuit performance involves identification of such paths determining the achievable path delay fault coverage and reducing the subsequent test generation effort. The experimental results for two microprocessors (Parwan and DLX) indicate that a significant percentage of structurally testable paths are functionally untestable     

Flow patterns in gas-assisted injection molding process in a channel

The flow field of a long bubble steadily expelling a viscous fluid confined by two closely located parallel plates is examined. In order to investigate the influence of bubble size on the flow field, a theoretical bubble profile is used to replace the complicated procedure for computing simultaneously the interface between the gas surface and fluid flows. The present study showed the two typical flow patterns and also a third flow pattern of the stagnation point moving in the region of the bubble tip front during transformation of the two typical flow patterns. The vorticity patterns are also drawn for various bubble profiles and are examined for their effect on the flow. The velocity field is also presented from two different viewpoints and the phenomena is examined. The stagnation point located on the center line between the bubble tip to the upstream is only found in the small range of in a channel, where λ is ratio of the bubble width to the distance between two parallel plates.     

用流延法制备优质陶瓷基片的研究

本文概括了流延成型工艺的现状，介绍了有机基流延成型工艺中溶剂及添加剂的作用和选择原则，同时介绍了几种新的流延成型工艺。     

一种用单片机制作的高频正弦波逆变器

本文介绍一种简单廉价的单片机AT89C2051实现正弦波脉宽调制、保护的逆变器电路，以及逆变器的整体设计和工作原理，为小型正弦波逆变器的设计制作提供了一种较新的思路。