金属切削液在轴承加工中的应用

着重介绍金属切削液的分类、功能及其在轴承加工中的选用。在轴承加工中,一般有车削、铣削、钻削、铰削和磨削等多种加工工艺,其中磨削加工是一道非常重要的精密加工工序,如内圆磨削、外圆磨削、平面磨削和沟槽磨削等。轴承加工中使用的水基切削液不仅要具有冷却作用,还要有润滑、清洗和防锈的功能。重点介绍金属切削液的主要功能及其在轴承加工中的应用。     

Assessing the risk of “Kirkendall voiding” in Cu3Sn

A common location of sporadic, usually unpredictable, premature failures of both SnPb and Pb-free solder joints is within the intermetallic bond to one of the contact pads. Cu pads tend to be less prone to such defects than Ni/Au coated pads, but one phenomenon is a cause of growing concern for high reliability applications. Sporadic intermetallic problems are notoriously difficult to screen for, but at least a number of them are detectable right after assembly. However, the occasional formation of a network of voids within the Cu₃Sn layer forming when soldering to Cu pads is rarely noticeable until much later. To make matters worse, efforts to establish practical engineering tests for purposes of identification and screening have usually not been successful.The root cause of the so-called ‘Kirkendall voiding’ has been shown to be associated with the quality of the electroplated Cu, apparently as determined by the incorporation of minute amounts of specific organic impurities. The present work describes and discusses a series of potential tests that allow the sorting of electroplated Cu in terms of its propensity for Cu₃Sn voiding during soldering and subsequent aging. The times and efforts involved in these tests differ greatly, as do their effectiveness and accuracy. Individual tests may therefore be useful at various stages from supplier qualification to monitoring of batch to batch variations.     

奥氏体不锈钢TP321炉管焊缝铁素体含量控制实验分析

奥氏体不锈钢中铁素体含量既有有利的一面也有不利的影响,本文根据在实际工作中遇到具体的一种管材就此问题进行了分析和实验,对保证施工质量,防止炉管焊缝铁素体含量超标,有一定指导作用。     

超声振动辅助等离子沉积成形的研究

介绍了等离子沉积成形的原理、应用及其存在的优缺点,从超声原理出发介绍了超声振动对等离子沉积过程中晶粒及组织的影响,并设计了超声振动辅助等离子沉积成形的实验装置,对实验过程中以及该实验可能涉及的问题进行了探讨.     

Comparative study on internally heated and adiabatic regenerators in liquid desiccant air conditioning system

Liquid desiccant regeneration has important effect on performance of a liquid desiccant air conditioning system. Compared with conventional packed regenerator, internally heated regenerator is proposed to achieve better regeneration performance. This study emphasized on both regeneration rate and regeneration thermal efficiency to evaluate the performance of both regenerators. A validated heat and mass transfer model was used to analyse and compare the performance of internally heated and adiabatic regenerators. The results indicated that internally heated regenerator not only could increase the regenerate rate, but also could exhibit higher energy utilization efficiency. Different from adiabatic regenerator, internally heated regenerator can provide comparable regeneration efficiency and regeneration rate at low desiccant flow rate, so it should be a good alternative to avoid carryover of desiccant droplets. Higher air flow rate would result in a deduction of regeneration thermal efficiency although achieving higher regeneration rate. Suitable flow rate of the air should be considered carefully in liquid desiccant regeneration. The internally regenerator could have considerable prospect in liquid desiccant air conditioning application.     

浅析爆炸危险环境中电气设备的安装

主要介绍了在生产、加工、处理、转运或贮存过程中可能出现爆炸危险环境的新建、扩建和改建工程的电力设备安装工程中的保安技术。     

Development and test in grid of 630 kVA three-phase high temperature superconducting transformer

Abstract A 630-kVA 10.5 kV/0.4 kV three-phase high temperature superconducting (HTS) power transformer was successfully developed and tested in a live grid. The windings were wound by hermetic stainless steel-reinforced multi-filamentary Bi2223/Ag tapes. The structures of primary windings are solenoid with insulation and cooling path among layers, and those of secondary windings consist of double-pancakes connected in parallel. Toroidal cryostat is made from electrical insulating glass fiber reinforced plastics (GFRP) materials with room temperature bore for commercial amorphous alloy core with five limbs. Windings are laid in the toroidal cryostat so that the amorphous core operates at room temperature. An insulation technology of double-half wrapping up the Bi2223/Ag tape with Kapton film is used by a winding machine developed by the authors. Fundamental characteristics of the transformer are obtained by standard short-circuit and no-load tests, and it is shown that the transformer meets operating requirements in a live grid. __________ Translated from Proceedings of the CSEE, 2007, 27(27): 24–31 [译自:中国电机工程学报]     

AgIn共掺杂(AgIn)xPb1-2xTe化合物的合成及热电传输性能

用高温熔融法合成了Ag和In共掺的单相n型(AgIn)xPb1-2xTe化合物,研究了(AgIn)掺杂量x对(Ag-In)xPb1-2xTe(x=0.01～0.05)物相组成及热电性能的影响.结果表明:掺杂量x≤0.04时得到单相四元化合物,x=0.05时样品中出现了组成为AgInTe2第二相;(AgIn)xPb1-2xTe化合物的Seebeck系数随着x增加而增大,电导率随着掺杂量x增加而降低;化合物的热导率随着掺杂量x增大而减小;当x=0.01时,(AgIn)xPb1-2xTe化合物的热电性能指数值最大,在800K时达到1.1.