Phase transformation and interface segregation behavior in Si3N4 ceramics sintered with La2O3–Lu2O3 mixed additive

Microstructure and mechanical property of silicon nitride (Si₃N₄) ceramic are strongly dependent on the selection of sintering additives. When rare‐earth (RE) oxide is used as the sintering additive, segregation of RE ions at interface between Si₃N₄ grain and intergranular glassy film (IGF) is believed to play a critical role. Although the ionic radius of RE ion is known to be an empirical parameter to modify the mechanical property, the correlation between the segregated ions and their ionic radii is still under controversy. In order to address this issue, (i) rate of α‐β phase transformation and (ii) segregation behavior at the interface were studied for Si₃N₄ ceramics sintered using mixture of La₂O₃ and Lu₂O₃ as additives in this study. Specimens of Lu content 30% and higher exhibited lower activation energies for the α‐β phase transformation as compared with those of Lu content 20% and lower. In terms of the segregation behavior, La was preferably segregated at one site and Lu at the other site along β‐Si₃N₄/IGF interface in the specimens of Lu content 30% and higher. It is understood from these results that Lu segregation site should be more closely related with grain growth.     

Acceleration of the Rate of Silver Nanoparticle Formation Using Microbubbles in a Sonochemical Process

The effect of the addition of microbubbles on the formation of silver nanoparticles produced in an ultrasonic radiation-mediated process was investigated. The addition of microbubbles with an area-based median diameter of 26.0?µm and a bubble volume density of 0.18?cm³/L significantly increased the silver nanoparticle formation rate during the sonochemical process. The size distribution of the silver nanoparticles was largely unaffected by the addition of the microbubbles. The influence of changes in the microbubble volume density on the formation of the silver nanoparticles was also investigated; it was confirmed that the rate of formation of the silver nanoparticles increased moderately with increasing volume density. The gradient in absorption spectra was approximately 30 times larger for the case when microbubbles (median diameter: 28.3?µm) were added at 0.74?cm³/L, compared with the case without microbubbles. The results suggested that the microbubbles provided reaction sites similar to cavitation bubbles in the ultrasonic reaction.     

The effect of atmospheric plasma treatment of recycled carbon fiber at different plasma powers on recycled carbon fiber and its polypropylene composites

To increase the mechanical properties of recycled carbon fiber-reinforced polypropylene (PP) composites, recycled carbon fibers (RCF) were subjected to atmospheric plasma treatment at different plasma powers (100, 200, and 300 W). The changes on surface topography and roughness of RCF were examined by atomic force microscopy. Plasma treatment of RCF increased the roughness value of RCF. The variation of surface elemental compositions and tensile strength of RCF were determined by using X-ray photoelectron spectroscopy and tensile test, respectively. Plasma-treated RCF-reinforced PP composites were fabricated using high speed thermo-kinetic mixer. Plasma treatment of RCF at 100 W increased the tensile and flexural strength values of RCF-reinforced PP composites considerably by 17 and 11%, respectively. However, plasma treatment of RCF at higher plasma powers (200 W and 300 W) decreased tensile and flexural strength values of composites because of the etching of RCF. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47131.     

Development of silicon wafer packaging technology for deep UV LED

This paper reports a deep‐ultraviolet LED (deep‐UV‐LED) package based on silicon MEMS process technology (Si‐PKG). The package consists of a cavity formed by silicon crystalline anisotropic etching, through‐silicon vias (TSVs) filled with electroplated Cu, bonding metals made of electroplated Ni/AuSn and a quartz lid for hermetic sealing. A deep‐UV LED die is directly mounted in the Si‐PKG by AuSn eutectic bonding without a submount. It has advantages in terms of size, heat dissipation, light utilization efficiency, productivity and cost over conventional AlN ceramic packages. We confirmed a light output of 30 mW and effective reflection on Si (111) cavity slopes in the Si‐PKG. Based on simulation, further improvement of the optical output is expected by optimizing DUV‐LED die mount condition.     

Visual image of neighbors to elicit wandering behavior in the soldier crab

The soldier crab appears in great numbers and feeds while wandering during daytime low tide. When they see an approaching object, they screw themselves into the sand. The mechanism of formation of mass wandering has not been clarified. In this study, to investigate if the soldier crabs use visual images of neighbors as a stimulus for wandering, dummy crabs were presented to crabs. In the experiments, one, two, four, or eight dummies were placed in a circle on a sand arena. Each crab was placed in the center of the arena and observed whether it burrowed into the sand or wandered. The proportions of wandering individuals in each experimental treatment were compared with the expected value. Significantly more crabs were wanderers when only two and four dummies were present. This result suggests that soldier crabs chose burrowing or wandering depending on visual image of the distribution of the neighbors.     

Effects of Using Alternative Extreme Pressure (EP) and Anti-Wear (AW) Additives with Oxy-Nitrided Samples

Oxy-nitriding is a widely used industrial process aiming to improve the tribological properties and performance of components. Previous studies have shown the effectiveness of the treatment with friction and wear performance, but very few have focussed on optimising this behaviour. The lubrication properties of several EP and AW additives were examined to investigate their effectiveness in improving the tribological properties of the layers formed after treatment. Previous studies showed the presence of an oxide layer on the sample could improve the effectiveness of the sulphurised olefin (SO) and tricresyl phosphate (TCP) additives. The friction and wear behaviour of oxy-nitrided samples were analysed using a tribometer and surface profiler. Scanning electron microscope, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy were employed to identify the morphologies and chemical compositions of the treated surface before and after testing. No real effect on friction was observed when using the SO or TCP additives, mostly due to lack of interaction with the less reactive iron nitride layer and their roles as anti-wear additives. However, when the zinc dialkyldithiophosphate-containing lubricant was used, a higher friction coefficient was observed. Greater improvements in anti-wear properties with the presence of additives in comparison with only using base oil were reported, with the TCP additive producing the lowest wear rates. The study effectively demonstrated that the additive package type used could impact the tribological and tribochemical properties of oxy-nitrided surfaces.     

Density-Functional Theoretical Study on the Role of Lewis and Brønsted Acid Sites on CeO2(110) Surfaces for Nitrile Hydration

Hydration of cyanopyridine on CeO₂(110) surfaces was studied using periodic DFT+U calculations. One of two adsorption modes of 2-cyanopyridine occurs with two-point interaction which causes substrate specificity. A catalytic cycle for the hydration of 2-cyanopyridine was proposed. Cooperativity of Lewis and Brønsted acid sites was found to stabilize the intermediates for the hydration.     

Development of gap sensing system for narrow gap laser welding

Narrow gap welding with an oscillation laser beam is one of the effective processes for thick plate welding. To put this welding process into practical manufacturing, a groove-sensing system using image processing for narrow gap welding with an oscillation laser beam is used. This developed system uses still images of the weld zone taken by a coaxial CMOS camera. It can recognize the position of the groove wall by analysing the brightness distribution in the still image. It can then control the oscillation width and the laser-irradiated area by calculating the groove width and the groove centre position. Some narrow gap welding experiments were performed to evaluate the performance of the developed system. The results revealed that the developed system is effective for narrow gap welding with an oscillation laser beam. Using this system, the narrow gap groove can be welded even if the groove width has changed during the welding process.