Determination of Interfacial Fracture Toughness of Thermal Spray Coatings by Indentation

Adhesion is an important and basic property for thermal spray coatings. The standard tensile test method “ISO 14916” is usually used to evaluate the adhesive strength of coatings. On the other hand, the indentation test method has some advantages to evaluate the interfacial fracture toughness as the adhesive strength, arising from the following reasons: the test procedure and the specimen preparation are easy in comparison with the typical testing method. Collaborative research has been conducted by “Committee on Standard Development” in the Japan Thermal Spray Society to establish a standard test method for evaluating interfacial fracture toughness of thermal spray coatings using a conventional Vickers indenter. This article reports the differences among collaborators in round-robin tests performed in this committee and discusses the validity of the test method and test conditions with respect to the test results and finite element analyses. Comparison among collaborators reveals that interfacial fracture toughness can be obtained with a small scattering from the indentation test under constraints found on the basis of the results.     

Upper extremity interaction with a deploying side airbag: a characterization of elbow joint loading

Computer simulations, dummy experiments with a new enhanced upper extremity and small female cadaver experiments were used to analyze the small female upper extremity response under side airbag loading. After establishing a worst case initial position, three tests were performed with the fifth percentile female hybrid III anthropometric test dummy and six experiments with small female cadaver subjects. A new fifth percentile female enhanced upper extremity was developed for the dummy experiments that included a two-axis wrist load cell in addition to the existing six-axis load cells in both the forearm and humerus. Forearm pronation was also included in the new dummy upper extremity to increase the biofidelity of the interaction with the handgrip. Instrumentation for both the cadaver and dummy tests included accelerometers and MHD angular rate sensors on the forearm, humerus, upper and lower spine. In order to quantify the applied loads to the cadaver hand and wrist from the door mounted handgrip, the handgrip was mounted to the door through a five-axis load cell and instrumented with accelerometers for inertial compensation. All six of the cadaver tests resulted in upper extremity injuries including comminuted mid-shaft humerus fractures, osteochondral fractures of the elbow joint surfaces, a transverse fracture of the distal radius and an osteochondral fracture of the lunate carpal bone. The results from the 6 cadaver tests presented in this study were combined with the results from 12 previous cadaver tests. A multivariate logistic regression analysis was performed to investigate the correlation between observed injuries and measured occupant response. Using inertially compensated force measurements from the dummy mid-shaft forearm load cell, the linear combination of elbow axial force and shear force was significantly (P=0.05) correlated to the observed elbow injuries.     

Tip-induced excitation of a single vortex in nano-size superconductors using scanning tunneling microscopy

A single vortex is excited into nano-size Pb superconducting island structures by a local current injection from a probe tip of a scanning tunneling microscope. For the excitation, a sufficient amount and duration of the pulsed current are required. Injecting the current at peripheral sites is more effective than the center for the vortex excitation. Time-dependent Ginzburg-Landau calculations suggest that a current-induced normal-state area, which can be nucleated by the tunneling current exceeding the critical current and expanded by the Joule heating, reduces the required magnetic field for the vortex penetration and excites a vortex into the islands.     

Metal cluster complex primary ion beam source for secondary ion mass spectrometry (SIMS)

To develop a solution-type ion beam source utilizing a wide variety of metal cluster complexes that are stable only in organic solvents, we have investigated an electrospray method for transferring ions from solutions to gas phase. As initial experiments, we have studied electrospray characteristics of ethanol solutions containing a room-temperature molten salt (i.e., an ionic liquid) and acetic acid as alternatives to solutions of metal cluster complexes. In electrospray experiments, we used a stainless-steel capillary with an inner diameter of 30 μm. Experimental results showed that electrosprayed currents increased with applied voltage in both positive-ion and negative-ion modes. In addition to positive currents, stable negative currents were also confirmed to be produced. Current exceeding 250 nA was produced at 2 kV with a flow rate of 2 μL/min at a concentration of 1 × 10⁻³ mol/L. It was confirmed that several nA out of electrosprayed currents were delivered through an orifice (120 μm internal diameter) into a vacuum chamber. Experimental results indicate that the electrospray method seems to be applicable to an ion beam source for utilizing massive metal cluster complexes in solutions.     

High-Mobility 2D Hole Gas at a SrTiO3 Interface

Strontium titanate (SrTiO₃ or STO) is important for oxide-based electronics as it serves as a standard substrate for a wide range of high-temperature superconducting cuprates, colossal magnetoresistive manganites, and multiferroics. Moreover, in its heterostructures with different materials, STO exhibits a broad spectrum of important physics such as superconductivity, magnetism, the quantum Hall effect, giant thermoelectric effect, and colossal ionic conductivity, most of which emerge in a two-dimensional (2D) electron gas (2DEG) formed at an STO interface. However, little is known about its counterpart system, a 2D hole gas (2DHG) at the STO interface. Here, a simple way of realizing a 2DHG with an ultrahigh mobility of 24 000 cm² V⁻¹ s⁻¹ is demonstrated using an interface between STO and a thin amorphous FeO_y layer, made by depositing a sub-nanometer-thick Fe layer on an STO substrate at room temperature. This mobility is the highest among those reported for holes in oxides. The carrier type can be switched from p-type (2DHG) to n-type (2DEG) by controlling the Fe thickness. This unprecedented method of forming a 2DHG at an STO interface provides a pathway to unexplored hole-related physics in this system and enables extremely low-cost and high-speed oxide electronics.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current—voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current—voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current—voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current—voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent ∑ 1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

Removal of malachite green by using an invasive marine alga Caulerpa racemosa var. cylindracea

The biosorption of a cationic dye, malachite green oxalate (MG) from aqueous solution onto an invasive marine alga Caulerpa racemosa var. cylindracea (CRC) was investigated at different temperatures (298, 308 and 318 K). The dye adsorption onto CRC was confirmed by FTIR analysis. Equilibrium data were analyzed using Freundlich, Langmuir and Dubinin-Radushkevich (DR) equations. All of the isotherm parameters were calculated. The Freundlich model gave a better conformity than Langmuir equation. The mean free energy values (E) from DR isotherm were also estimated. In order to clarify the sorption kinetic, the fit of pseudo-first-order kinetic model, second-order kinetic model and intraparticle diffusion model were investigated. It was obtained that the biosorption process followed the pseudo-second-order rate kinetics. From thermodynamic studies the free energy changes were found to be -7.078, -9.848 and -10.864 kJ mol(-1) for 298, 308 and 318 K, respectively. This implied the spontaneous nature of biosorption and the type of adsorption as physisorption. Activation energy value for MG sorption (E(a)) was found to be 37.14 kJ mol(-1). It could be also derived that this result supported physisorption as a type of adsorption.     

Development of a detector for ultratrace nitrogen in argon using low-pressure, capillary glow discharge molecular emission spectrophotometry

A highly sensitive detector was developed for determining parts per billion of nitrogen in high-purity argon. The method is based on the spectrophotometric determination of the emission intensity from the nitrogen molecule excited in the lowest vibrational transitions of the electronic C(3)Π(u) → B(3)Π(g) system. A capillary glow discharge technique was applied to excite nitrogen in an argon flow at several Torr. The low-pressure, capillary glow discharge method offered high sensitivity for detecting trace nitrogen in argon. The response of the detector was proportional in the range of nitrogen concentrations from 0.1 ppb, which correspond to S/N = 3, to 100 ppm.     

Effects of substrate material on diamond growth from CO-H2 plasma

Diamond synthesis from CO-H₂ plasma has been carried out on various substrate materials, e.g. metals: nickel, cobalt, tungsten, molybdenum, copper and ceramics: SiC, SiO₂, Al₂O₃, ZrO₂, AlN. Diamond formation was confirmed on every substrate with the exception of cobalt and nickel. The highest density of diamond nucleation, over 10⁸ cm^–2, was obtained on amorphous SiO₂, the carbide-forming metals tungsten and molybdenum and on SiC; on these the nucleation density was one order of magnitude higher than on the other substrates. Diamond films prepared on tungsten, molybdenum and SiC substrates had a strong adhesion force: 1.3 to 1.5 kg mm^–2.