热分析在PVA纤维预处理中的应用

用差热、热重法对原丝的热性能及由不同预处理方法所引起的PVA纤维的热行为变化进行了研究;并通过模拟脱水条件,用不同升温速率,求出了经不同预处理纤维的脱水反应活化能。结果表明,PVA原丝在230℃有一软化点,三种预处理都不同程度地影响了原丝的热效应变化;纤维在180～340℃主要为脱水反应;原丝及经脱水剂、O_3和O_3综合脱水剂处理的纤维,其脱水反应的表观活化能分别为:164.3kJ/mol,92.9kJ/mol,130.5kJ/mol和117.6kJ/mol。     

Zeolite coated interdigital capacitors as a new type of gas sensor

The adsorption of a gas influences the dielectric constant of zeolites. This property is used as the sensitive component of a gas sensor.

Planar interdigital capacitors were coated with thin films of zeolites. When gas molecules are adsorbed, the dielectric constant of the zeolite is altered, which causes a change in the capacitance of the interdigital capacitor. This change is strongly dependent on the concentration of adsorbate in the gas phase.     

Vandermonde and resultant matrices: An abstract approach

Vandermonde and resultant matrices: An abstract approach     

Contributing authors

Contributing authors     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

STM tunneling spectroscopy on high Tc superconductors

STM tunneling spectroscopy has been performed on the bulk single crystals of BiSrCaCuO (BSCCO) and the epitaxial thin films of YBaCuO (YBCO) at cryogenic temperatures. The STM images and tunneling spectra observed on the (001) surfaces can be classified into three cases; 1) Atomic image is visible. However, the tunneling spectrum shows semiconducting or smeared superconducting gap structures, depending on the tip-sample distance. 2) Clear atomic image can not be obtained. But, the tunneling spectrum shows flat bottom region with quite low zero bias conductance. 3) Tunneling spectra demonstrate gapless behavior, independent of the tip-sample separation. These observations support the quasi-2D electronic picture in whichs-wave like 2D superconducting layers are coupled with each other through the Josephson effect.     

高放废液化学成分分析

概述了高放废液中25种阳离子、5种阴离子以及总蒸残物、总氧化物、密度和游离酸的分析方法。对核燃料后处理高放废液进行取样分析,其主要化学成分采用两种以上不同原理的方法作对比测定,结果相互符合情况良好,为高放废液处理处置研究设计,提供了完整、准确的基础数据。     

Determination of the relationship of pressure to process time in pneumatic forming of a round membrane in the superplastic condition

The deformation of a round membrane into a cylindrical matrix is considered. The relationship of pressure to time of the process of pneumatic forming in the superplastic condition is established. The results obtained are compared with known data. A conclusion is drawn on the applicability of the proposed approach for calculation of the production parameters of forming of axisymmetric parts in the superplastic condition.Translated from Problemy Prochnosti, No. 11, pp. 71–75, November, 1993.     

Dimensional scaling for impact cratering and perforation

The issue of generic scaling laws able to adequately predict (within better than 20%) cratering in semi-infinite targets and perforations through finite thickness targets was revisited. The approach used was to apply physical logic for hydrodynamics in a consistent manner able to account for chunky-body impacts such that the only variables needed are those directly related to known material properties for both the impactor and target. The analyses were compared and verified versus CTH hydrodynamic code calculations and existing experimental data. Comparisons with previous scaling laws were also performed to identify which (if any) were good for generic purposes. This paper is a short synopsis of the full report [1] available through the NASA Langley Research Center, LDEF Science Office.     

车辆换档品质控制阀动态特性研究

建立了某车辆换档品质控制阀的仿真模型，分析了反馈油孔直径、背压及弹簧刚度等因素对动态性能的影响。台架试验验证了所建模型的正确性及有效性。研究结果可为车辆换档品质控制系统的设计、改进及性能预测提供依据。