黄骅坳陷白水头-唐家河地区东营组地层地震模拟及响应曲线分析

根据对黄骅坳陷白水头—唐家河地区东营组钻井资料的统计分析，设计了3种不同地质模型．用于分析不同厚度、不同孔隙度和不同流体性质的储层所表现出的地层速度和密度特性，进而通过地震正演模拟研究，得到不同储层参数状况下的响应曲线。分析响应曲线发现，在该地区，当含水砂岩厚度为20m时．其地震反射振幅最大；而含油帮岩在厚度为18m时达到最大。当孔隙度达到22％时．含油砂岩的地震反射振幅会发生极性反转；而含水砂岩在孔隙度为28％时极性反转。这就为该地区的地震储层预测提供了依据。     

从审美意向看东西方服饰文化精神

通过对中西方服饰的审美文化的探讨,分析服装设计的审美特性和美学意蕴。从全面的、科学的角度来客观评价东西方服饰文化的审美价值。     

ASON在当前应用中存在的问题及分析

对ASON在当前应用中可能碰到的几个问题进行了分析，并提出了看法。     

醋酸甲酯在Cs_(1.5)PW/SiO_2催化剂上的水解反应

通过改变阳离子的种类与配比,制备了一系列SiO2负载的磷钨酸盐催化剂,考察了制备方法对催化剂性能的影响,采用傅里叶变换红外光谱、X射线衍射、X射线荧光光谱、环境扫描电子显微镜等方法对催化剂进行了表征,并考察了该系列催化剂对醋酸甲酯水解反应的活性。实验结果表明,Cs1.5PW/SiO2催化剂的活性最好,当Cs1.5PW负载量(质量分数)为30%时,Cs1.5PW的Keggin结构保持完好,没有硅钨酸阴离子形成,Cs1.5PW在SiO2载体上高度分散;在反应温度55℃、反应时间2h的条件下,醋酸甲酯的转化率为35.79%,约为均相磷钨酸催化剂的1.3倍。该催化剂重复使用4次后,醋酸甲酯的转化率稳定在25%;80℃下反应2h,与NKC-9磺酸树脂催化剂相比,醋酸甲酯的转化率提高了5.17%。     

重油纳米化助燃效果研究与表征

将复配的分散剂加入重油中制备得到重油纳米颗粒，采用氧弹热值对比法对所研制的纳米化重油进行实验室评价。研究结果表明，纳米化后的重油燃烧性能得到了改善，在掺水量为3％～12％时，重油的燃烧效率提高了2．5％～6．1％。通过TEM观察，纳米化后的重油呈水包油（O／W）型乳液结构，油水界面清晰，界面膜较厚，乳化油粒径约为20～50nm，油水分散均匀，并且分散后的重油粘度增幅小，掺水量在15％以内，粘度增幅不超过20％，并且随着掺水量的增加，乳化重油的粘度逐渐减少。另外，乳化重油稳定性好，室温下至少可保存6个月，在80℃下存放3天未发生破乳现象。     

Measurement System of Uniformity between Breech Horizontal Platform and Datum Tube Axis of Rocket Artillery

The purpose of this development is to detect the parallelism between the breech horizontal platform and the datum tube axis of the rocket artillery. The located aiming mechanism at the muzzle and located adjustment mechanism at the breech are designed in the system. Besides those, the system also uses an autocollimator with accuracy of 1″ and a collimating mirror together to determine the axis of the datum tube. An electronic level with accuracy of 2″ is employed to measure and display the value of the included angle and the parameter of the inclined direction. The entire accuracy of this system is σ≤± 9.1″. This paper describes the composition and the operating principle of the system and analyzes the accuracy. The development of this system supplies reliable measurement method for new rocket artilleries and artilleries, and this technology is of a good application prospect.     

奥氏体化温度对含稀土半钢力学性能的影响

研究了奥氏体化温度对含稀土半钢力学性能的影响 ,结果表明 ,半钢的冲击韧度 (αK)、抗弯强度 (σbb)和相对韧性 (σbb× f )随奥氏体化温度的变化较明显 ,而硬度 (HRC)受奥氏体化温度影响较小 ,当奥氏体化温度为 960℃时 ,其综合力学性能最佳     

非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

平纹织物复合材料的弹性模量预测

利用细观力学的代表体积元(RVE)法,预测了平纹织物复合材料的弹性模量。建立了表征RVE形态的数学模型,分析了细观结构与宏观性能之间的关系,编制了从组分材料的弹性性能推测复合材料的弹性性能的预测程序。对理论预测进行了实验验证,理论值与实测值在一定误差范围内能较好吻合,说明此预测方法具有一定的可靠性。     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.