炼钢厂钢水温度—时间优化匹配系统开发

根据软件开发的基本原则，提出了炼钢厂的钢水温度－时间优化匹配系统开发总则和结构设计，并闻相应的软，硬件系统。     

饭店的绿色建筑设计初探

事实上，许多饭店存在的许多环境问题都是由于饭店的“先天不足”造成的。因此，饭店绿色建筑设计是创建绿色饭店的根本环节。文章对绿色建筑设计的基本原则和内容作了初步的探讨。     

频率/待测量变换的GAL、ERROM设计方法

本文提出了以通用阵列逻辑器件 GAL 和只读存贮器 EPROM 为核心器件的频率/待测量变换的设计方法。配以数字式传感器及用最小二乘法编制的曲线自动分段拟合程序生成的 EPROM 中的数据,可用于力、温度、光强等非电量的测量显示和控制。这种装置与采用微处理器的电路相比,有相同的测量精度,电路简单,而且保密性好.     

CTS-26型超声探伤仪典型故障的分析与排除

在简要介绍CTS-26型超声探伤仪工作原理及组成的基础上。对其几种典型故障作了具体的分析和处理。     

Modeling the Absorption of Acidic Gases by Alkanolamine Solutions Incorporating Several Reactions

A general model, based on double film theory, is developed to study absorption with chemical reactions. In the liquid film region, the model is a set of differential equations that describe the mass transfer accompanying several chemical reactions; the resolution of the system is achieved by the finite difference method using an implicit scheme combined with Newton's method. Continuity equations and equilibrium coefficients are exploited in the treatment of the bulk region, which is based on the Newton‐Raphson method; the results are used directly as boundary conditions in the liquid film equations. Maxwell‐Stefan equations have been used as a rigorous approach in this model.     

Influence of rubber content in ABS in wide range on the mechanical properties and morphology of PC/ABS blends with different composition

A series of acrylonitrile–butadiene–styrene (ABS) with different rubber content were prepared by diluting ABS grafting copolymer containing 60% rubber with a styrene–acrylonitrile copolymer. ABS prepared were blended with bisphenol‐A‐polycarbonate (PC) at the ratio of 70/30, 50/50, and 30/70 to prepare PC/ABS blends. Influence of rubber content in ABS on the properties of ABS and PC/ABS blends were investigated. PC/ABS blends with different compositions got good toughness when the rubber in ABS increased to the level that ABS itself got good toughness. The tensile properties and processability of PC/ABS blends decreased with the increase of the total rubber content introduced into the blends. ABS with the rubber content of 30 wt% is most suitable to be used to prepare PC/ABS blends. The rubber content in ABS affected the viscosity of ABS, and subsequently the viscosity ratio of PC to ABS. As a result, the morphology of PC/ABS blends varied. The increase of rubber content in ABS results in finer structure of PC/ABS blends. POLYM. ENG. SCI. 46:1476–1484, 2006. © 2006 Society of Plastics Engineers.     

Kernel-based least squares policy iteration for reinforcement learning.

In this paper, we present a kernel-based least squares policy iteration (KLSPI) algorithm for reinforcement learning (RL) in large or continuous state spaces, which can be used to realize adaptive feedback control of uncertain dynamic systems. By using KLSPI, near-optimal control policies can be obtained without much a priori knowledge on dynamic models of control plants. In KLSPI, Mercer kernels are used in the policy evaluation of a policy iteration process, where a new kernel-based least squares temporal-difference algorithm called KLSTD-Q is proposed for efficient policy evaluation. To keep the sparsity and improve the generalization ability of KLSTD-Q solutions, a kernel sparsification procedure based on approximate linear dependency (ALD) is performed. Compared to the previous works on approximate RL methods, KLSPI makes two progresses to eliminate the main difficulties of existing results. One is the better convergence and (near) optimality guarantee by using the KLSTD-Q algorithm for policy evaluation with high precision. The other is the automatic feature selection using the ALD-based kernel sparsification. Therefore, the KLSPI algorithm provides a general RL method with generalization performance and convergence guarantee for large-scale Markov decision problems (MDPs). Experimental results on a typical RL task for a stochastic chain problem demonstrate that KLSPI can consistently achieve better learning efficiency and policy quality than the previous least squares policy iteration (LSPI) algorithm. Furthermore, the KLSPI method was also evaluated on two nonlinear feedback control problems, including a ship heading control problem and the swing up control of a double-link underactuated pendulum called acrobot. Simulation results illustrate that the proposed method can optimize controller performance using little a priori information of uncertain dynamic systems. It is also demonstrated that KLSPI can be applied to online learning control by incorporating an initial controller to ensure online performance.     

Optimal Conditions for Preparing Ultra-Fine CeO2 Powders in A Submerged Circulative Impinging Stream Reactor

Cerium carbonate powders were produced in a submerged circulation impinging stream reactor (SCISR) from Ce(NO3)3·6H2O. NH4HCO3 was used as a precipitant in the reaction. Cerium carbonate powders were roasted to produce ultra-fine cerium dioxide (CeO2) powders. The optimal conditions of such production process were obtained by orthogonal and one-factor experiments. The results showed that ultra-fine and narrowly distributed cerium carbonate powders were produced under the optimal flowing conditions. The concentrations of Ce(NO3)3 and NH4HCO3 solutions were 0.25 and 0.3 mol·L-1, respectively. The concentration of PEG4000 added in these two solutions was 4 g·L-1. The stirring ratio, reaction temperature, feeding time, solution pH, reaction time and digestion time were 900 r·min-1, 80 ℃, 20 min, 5～6, 5 min and 1 h, respectively. The final product, CeO2 powders, was obtained by roasting the produced cerium carbonate in air for 3 h at 500 ℃. The finally produced CeO2 powders were torispherical particles with a narrow size distribution of 0.8～2.5 μm. The crystal structure of CeO2 powders belonged to cubic crystal system and its space point group was O5H-FM3M. Under optimal conditions, powders produced by SCISR were finer and more narrowly distributed than that by Stirred Tank Reactor (STR).     

On the Hertzian fatigue cone crack propagation in ceramics

The Hertzian cone crack initiation and propagation in ceramics under cyclic fatigue loading with a spherical indenter is studied. Unlike the so-called quasi-static Hertzian cone crack, the fatigue Hertzian cone crack propagation eliminates the dynamic effect on unstable crack propagation. As such, the crack is found to propagate following the path of pure mode I type. We use an elasticity approach, a finite element analysis, and an empirical analysis to investigate the Hertzian cone crack in three stages: crack initiation, crack propagation, and crack kinking. The mechanism of the multiple concentric cone cracks is also explained. The purpose is to understand and predict the behavior of the formation of the Hertzian fatigue cone crack using available modeling tools.Zheng Chen is currently with Space Power Institute, Auburn University.