A network management architecture for robust packet routing in meshoptical access networks

We describe an architecture for an optical local area network (LAN) or metropolitan area network (MAN) access. The architecture allows for bandwidth sharing within a wavelength and is robust to both link and node failures. The architecture can be utilized with an arbitrary, link-redundant mesh network (node-redundancy is necessary only to handle all node failures), and assumes neither the use of a star topology nor the ability to embed such a topology within the physical mesh. Reservation of, bandwidth is performed in a centralized fashion at a (replicated) head end node, simplifying the implementation of complex sharing policies relative to implementation on a distributed set of routers. Unlike a router, however, the head end does not take any action on individual packets and, in particular, does not buffer packets. The architecture thus avoids the difficulties of processing packets in the optical domain while allowing for packetized shared access of wavelengths. We describe the route construction scheme and prove its ability to recover from single link and single node failures, outline a flexible medium access protocol and discuss the implications for implementing specific policies, and propose a simple implementation of the recovery protocol in terms of state machines for per-link devices     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

温度计量技术进展近况

近年来，在把ITS－90更方便地传递到工作用温度计，温度测量仪表采用信息技术和特殊工业场合测温应用方面均取得了一些进展。本文介绍了国内外温度技术在这些方面进展的状况。对温度定点，校验器，热电偶和热电阻测温，辐射测温，光纤测温和信息时代自动化系统中的温度检测仪表的重要进展分别作了介绍。     

机动武器系统的含间隙动力学研究--下篇:系统仿真

本文把中篇建立的间隙铰模型引入多体系统动力学分析中,得到了一种处理含间隙多体系统动力学问题的一般方法.应用这种方法对机动武器的发射过程进行了原理性的仿真,验证了前面建立的碰撞模型和间隙模型,并分析了间隙对导弹运动状态的影响.导弹发射过程具有变拓扑的特点,本文方法提供了一种处理这类问题的思路.     

Interface characteristics and mechanical properties of carbon fibre reinforced copper composites

Interface characteristics of carbon fibre reinforced copper matrix composites materials with various interface states and their effect on the flexural strength of composites have been studied. Interfacial states are mechanical bonding, dissolution bonding and reaction bonding. To a certain extent, raising the interfacial strength enables an increase in the flexural strength due to prevention of carbon fibre being pulled out under low stress during fracture process of composites. Raising the interfacial bondage strength, causes the brittleness of composites to increase; the fracture surface of composites is converted from a fibre pull-out model to a fibre even model. While strengthening the interface bondage, the extent of chemical reaction and dissolution at the interface must be controlled to avoid degrading the carbon fibre.     

Template-assisted synthesis of lamellar mesostructured hydroxyapatites

Novel lamellar mesostructured hydroxyapatites have firstly been synthesized by template-assisted technique. The mild and nontoxic surfactant, phosphoric acid monododecyl ester (MAP), is used to act as a structure-directing template. The structure of sample was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, Scanning electron microscope and Transmission electron microscopy. The results indicate that the obtained sample is a well-organized lamellar mesostructured hydroxyapatite with a uniform layer spacing of 3.64 nm.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。     

尿素解吸废液及甲醇残液联合处理工艺的应用

安阳化学工业集团公司(以下简称安化集团)现有2套200 kt/a尿素装置及1套60 kt/a甲醇装置.尿素及甲醇装置在生产过程中会产生大量的尿素解吸废液和甲醇残液,废液中的氨氮(NH3-N)含量和化学需氧量(CODCr)较高,给该公司废水的达标排放带来很大压力.