Measurement of the compressive creep strain rates of the individual phases within a lamellar microstructure

A fuducial line technique has been developed to determine the creep properties of the constituent phases within a lamellar composite subject to compression creep deformation. The technique can yield information on the total strain, creep rate, and the stress exponent and activation energy for creep of the individual phases within a lamellar microstructure. The contribution of interphase interfacial sliding to the strain of lamellar composites can also be evaluated by using the fiducial line technique. Application of the fiducial line analysis to a two-phase TiAl/Ti₃Al lamellar alloy deformed in compression at 1080K and 380MPa yields good agreement between the creep strain determined using the fiducial line analysis and the value directly measured from the crept specimen. The fiducial line analysis reveals that the TiAl phase within the two-phase TiAl/Ti₃Al lamellar microstructure creeps 2.2 times faster than the Ti₃Al phase and that interfacial sliding does not contribute to creep deformation of this alloy, within the resolution limit of the fiducial line experiment.     

江苏省本地电话网结构与发展

分片汇接的网状网结构是江苏省本地电话网的基本框架,而汇接局和连接汇接局的传输系统则是网路规划与通信建设的重点。     

Determining elasticity and strength characteristics of powder coating

Methods are described for forming coating specimens and testing them in pure bending. The proposed tester gives adequate accuracy in determining the elastic characteristics and strength for thin specimens (up to 0.1 mm) of brittle materials of powder-coating type.Translated from Problemy Prochnosti, No. 3, pp. 94–97, March, 1993.     

PC／PET共混物的非等温结晶动力学

采用等速变温ＤＳＣ法对ＰＣ／ＰＥＴ共混体系的非等温结晶动力学进行了研究，结果表明，从玻璃态结晶时，随着ＰＣ含量的增加，ＰＥＴ组分的结晶速率先增加后降低。耐从熔体结晶时，体系的结晶速率随着ＰＣ含量的增加而增加，讨论了ＰＣ对ＰＥＴ组分结晶过程的影响。     

线性时变系统的区间稳定性与鲁棒稳定性

本文应用向量比较定理研究线性时变系统的区间稳定性和具非线性时变摄动的线性时变系统的鲁棒稳定性，所得的新结果包含文献的一些主要结果作为特例，本文的研究方法说明向量比较方法是分析区间稳定性和鲁棒稳定性的一种自然而有力的工具。     

Instron texture profile of buffalo milk cheddar cheese as influenced by composition and ripening changes

Buffalo milk Cheddar cheese samples of different ages were analysed for compositional attributes (CA), ripening indices (RI) and Instron Textural Profile (ITP). All samples were compositionally alike, except for pH and salt-in-moisture (SM) contents. RI showed significant variations. CA and RI showed highly significant correlations within themselves and with each other, except for moisture with pH, SM with moisture, MNFS, Fat and FDM and Fat with MNFS. The ITPs of cheeses showed significant variations and had highly significant intercorrelations indicating their interdependence. CA (except moisture and MNFS) and RI showed a highly significant correlationship with ITPs. Moisture content showed a highly significant correlationship with all ITPs, except cohesiveness and springiness, where it was significant. MNFS content showed significant correlations only with hardness and brittleness. Stepwise regression analysis revealed that MI was the most predominant factor influencing cheese texture, followed by pH, SM, FDM and TVFA. Knowing Ca and RI, the textural properties of cheeses can be forecast through mathematical equations. Similarly the age of cheese can also be predicted if RI and/or textural properties are known.     

Aromatic nitrations by mixed acid. Slow liquid-liquid reaction regime

Aromatic nitrations by mixed acid have been selected as a specific case of a heterogeneous liquid-liquid reaction. An extensive experimental programme has been followed using adiabatic and heat-flow calorimetry and pilot reactor experiments, supported by chemical analysis. A series of nitration experiments has been carried out to study the influences of different initial and operating conditions such as temperature, stirring speed and sulphuric acid concentration. In parallel, a mathematical model to predict the overall conversion rate has been developed. In this paper the mathematical modelling and the implementation and experimental validation for benzene, toluene and chlorobenzene mononitration in the kinetic control regime (slow liquid-liquid reaction) are presented and discussed.     

Separate assessment of porosity and uncombined carbon in cemented carbides

Porosity and uncombined carbon in cemented carbides are traditionally assessed by comparison to standardized microstructure charts, such as those in ISO 4505-1978. To improve the accuracy in the characterization a fully automatic image analysis procedure has been developed. The analysis is performed using light optical microscopy on unetched polished specimens. The implemented algorithm separates uncombined carbon, C-defects, from pores, A- and B-defects. Pores are approximately distributed in a random way in the structure. Uncombined carbon is on the other hand precipitated into clusters of carbon particles. This difference is together with defect size used as a base for the separation. Small defects situated close together are classified as C-defects, small isolated defects as A-pores and large defects as B-pores. Pores are found to be more round than the somewhat elongated C-defects. The difference in shape is significant and can also be used as a separation criterion.

Image analysis is used to quantitatively characterise the ISO 4505-1978 standard charts with respect to volume fraction, number density and size distribution of defects. The results are compared to measured distributions for true microstructures.     

Composition Dependence and Irradation Effects on Residual Resistivity in Cu-Al Alloys

Residual electrical resistivity due to short-range order has been calculated for Cu100-xAlx (x=9.13,13.56, 14.5 and 14.76 in at pct) alloys using pseudopotential approach, and the results have been discussed in the light of experimental studies of the local-order structure of these alloys. In case of Cu85.5Al14.5, change in the total residual electrical resistivity due to neutron-irradiation effects has been estimated by including contributions from the short-range order and static atomic displacement correction. Our results show a decrease in the residual resistivity in the irradiated Cu-Al solid solution as compared to the unirradiated sample. This is in accordance with the experimental results     

Analysis of thin walled structures using the boundary element method

In this article the direct boundary element formulations of stretching and bending plate problems are combined together to solve thin walled structures and other similar frames. The final system is obtained by assuming each individual plane structural element as a subregion. After the necessary transforms of these equations they can be combined together taking into account the displacement compatibility and equilibrium conditions.