A method for preparing collagen graft materials

The aim of this research was to develop a method of local production of collagen graft materials which are presently imported. The following methods were used to produce collagen membrane and sponge from human placentas and rat tail tendons. Collagen type I was isolated from human placenta and rat tail tendon by acetic acid extraction and characterised by SDS-PAGE. The collagen sponge was prepared by dissolving the collagen in HCl. The resulting dispersion was poured into a glass container, freeze-dried and then cross-linked by immersion in glutaraldehyde solution. It was then washed with distilled water and freeze-dried again. The collagen membrane was also similarly prepared by dispersing lyophilized collagen in HCl but then mixed with glutaraldehyde, exposed to U.V. light and later air dried.     

Use of sea water in the flotation of carbonate rich sedimentary phosphate rock

There is an appreciable amount of carbonaceous sedimentary phosphate deposits in the northern Africa and the Middle East which are expected to gain importance in the near future because of the depletion of the deposits in Florida. In many of the regions where phosphate deposits are found there is a shortage of fresh water, and sea is not very far. The use of sea water instead of fresh water in flotation of carbonaceous phosphate rock is successfully demonstrated. Thus an appreciable reduction in the operating cost and an ample amount of saving in the fresh water resources of the region is expected.     

Investigation of the stability of tablets prepared from sucrose and citric acid anhydride utilizing response surface methodology

Inversion of sucrose is a stability problem particularly of candies with acidic taste that contain sucrose and small amounts of organic acids such as citric acid, since the free d-fructose produced by hydrolysis is hygroscopic. The following possibilities were investigated for preventing the hydrolysis of sucrose in tablets containing sucrose and citric acid: Adding various amounts of tri-sodium citrate to the formulation to neutralize the citric acid, (Hot) melt coating of citric acid and tri-sodium citrate with a vegetable fat at different coating ratios, variation of the ratio of coated citric acid and tri-sodium citrate in formulations, and compressing the formulations with different compression forces. After tablet processing and storage of tablets, the concentration of d-fructose was determined on the basis of enzymatic reactions. A response surface central composite design was used. The above-mentioned variations were chosen as independent variables and the amount of d-fructose was chosen as response variable. The lowest rates of inversion could be achieved by increasing the content of tri-sodium citrate and the ratio of coating material and decreasing the ratio of coated citric acid and tri-sodium citrate in the tablet formulations. The compression force had no significant effect on the inversion of sucrose.     

Synthesis and characterization of novel polyacrylate-clay sol-gel materials

Organo-functional silanes which were able to form chemical bonds with kaolinite and could also have an affinity to the materials of concern here, were studied by the sol-gel process. Polymethacrylate with trialkoxy silyl functional groups were prepared, hydrolysed and co-condensed with kaolinite. The progress of the hydrolysis, which proceeded very slowly, was followed by Karl-Fischer titration. Thermal behavior was investigated by differential thermal analysis. The extent of the reaction leading to network formation was qualitatively followed by Fourier transform-infrared spectroscopy and X-ray diffraction. Free-radical polymerization was carried out ultrasonically in the presence of a catalyst. Trimethoxy silane end-capped silane was found to be covalently bonded to kaolinite. The copolymers, with various amounts of kaolinite, were then hydrolysed and co-condensed in the presence of a catalyst to yield sol-gel materials which have a controllable combination of properties of both the polymer and kaolinite.     

Inotropic effects of glyceryl trinitrate and spontaneous NO donors in the dog heart

Facial fractures may portend intracranial and skullbase injury and may lead to rapid compromise of the airway. Primary care physicians may provide emergency care for patients who have sustained facial trauma. After immediate resuscitation and stabilization, management of facial fractures requires knowledge of the anatomy, rapid treatment methods and identification of potential associated injuries for each type of facial fracture. Differentiation between the life-threatening aspects of these injuries and the less urgent, but more apparent, facial injuries will lessen the risk of complications such as bleeding, meningitis and asphyxia. Knowledge of the anatomy of the facial skeleton and of the potential injuries associated with each of the various types of facial fractures will facilitate effective management decisions. Consultation should be sought when functional features are involved or when the injury threatens to produce future cosmetic anomalies.     

The effect of elevated temperature and silicon addition on a cobalt-based wear resistant superalloy

The effects of an elevated temperature and a 5 wt% silicon addition on the resultant microstructure and inherent phases of Stellite 6 were investigated by using room and high temperature optical microscopy, X-ray diffraction, scanning electron microscopy (SEM) and also bulk hardness and microhardness measurements. It has been observed that exposing Stellite 6 to heat treatments at 1000°C results in a characteristic textured structure and coarsening of interdendritic regions due to bulk diffusion. In addition, both dendritic and interdendritic hardness values increase due to texture formation and increased amounts of carbide and intermetallic phases, respectively. On the other hand, silicon addition to Stellite 6 causes the transformation of the original spongy dendritic microstructure in as-cast Stellite 6 to a eutectic dendritic and skeleton interdendritic structure. Also, when silicon added Stellite 6 was heat treated at 1000°C, particulates emanating from the interdendritic skeleton become irregularly dispersed in the dendritic region. In addition, similarly to Stellite 6; a high temperature heat treatment results in an increase in hardness values of silicon added Stellite 6 due to the presence of an Co₂ Si intermetallic phase.     

General solution of one-dimensional,time dependent coupled heat flow systems

A new, powerful method of analysis, involving the combined use of finite integral transform and finite element techniques, is presented for the solution of time dependent heat flow systems composed of many one-dimensional elements connected through the nodes. This method leads to an eigenvalue problem which is not of the conventional Sturm-Liouville type. A procedure for the determination of the eigenvalues is described. The solution obtained is in the form of an infinite series and contains quasi-steady and transient terms. The general solution obtained can be applied in the mathematical modelling of many engineering applications such as the determination of the penetration of the daily temperature cycle into buildings, the analysis of heat transfer in array of extended surfaces in compact heat exchangers, and many others.     

The influence of process parameters and starting composition on the carbothermal production of sialon

The-sialons (Si_6-z Al _z O _z N_8-z ) can be produced by carbothermal reduction of kaolin. The reaction mechanism of the sialon formation has been studied by several methods. Firstly, the composition of the reaction product is determined by XRD as function of the reaction time at 1400 and 1 500 C. The influence of additives, pellet size, nitrogen flow and clay type on the reaction is studied. Secondly, the carbon monoxide leaving the furnace is monitored. By studying the changes in carbon monoxide output as a function of the above-mentioned parameters a better understanding of the reaction mechanism has been obtained.     

Chebyshev wavelet collocation method for magnetohydrodynamic flow equations

This study proposes Chebyshev wavelet collocation method for partial differential equation and applies to solve magnetohydrodynamic (MHD) flow equations in a rectangular duct in the presence of transverse external oblique magnetic field. Approximate solutions of velocity and induced magnetic field are obtained for steady‐state, fully developed, incompressible flow for a conducting fluid inside the duct. Numerical results of the MHD flow problem show that the accuracy of proposed method is quite good even in the case of a small number of grid points. The results for velocity and induced magnetic field are visualized in terms of graphics for values of Hartmann number H_a ≤ 1000.