Pyrolysis of Miscanthus Giganteus and wood pellets: TG-FTIR analysis and reaction kinetics

Characterisation of two biomass fuels (pelletised Miscanthus Giganteus and wood) was performed using thermogravimetric analysis with measurement of products by means of Fourier transform infrared spectroscopy (TG-FTIR). Three heating rate profiles were applied (10, 30 and 100 °C/min), with a final temperature of 900 °C. HCN and HNCO were found to be the major N-products, while the NH₃ fraction was detected to a minor extent. Kinetic parameters were obtained from the TG-FTIR results using a model based on parallel first-order reactions with a Gaussian distribution of activation energies. On the basis of the above kinetic analysis and product yields, input files for the functional group-devolatilisation, vaporisation, cross-linking biomass-pyrolysis model were prepared. The fit of model parameters to TG-FTIR product-evolution data was found to be generally good, but the model-predicted yields for some species did not fit experimental data at all heating rates. Further improvements in the model are needed to resolve above difficulty.     

Analysis of spontaneous electrochemical oscillations by energy distribution technique

Analysis of non-stationary electrochemical oscillations emerges utilization of the techniques allowing an observation of time evolution of their parameters such as instantaneous frequency, amplitude or frequency band. An algorithm of extraction of these parameters can be based on one of linear or quadratic time-frequency representations of oscillations record. In this paper, the authors present representatives of such transformations (Choi-Williams and Cone-shaped) originating from one of the most popular joint time-frequency energy distribution—Wigner-Ville distribution. Short introduction to the mathematics of the topic discussed is provided, then the authors present an example of application in the analysis of current oscillations of copper dissolution process.     

Problems of Wastewater Treatment and Methods of Solving Them

The studies show that in the combined use of biological and chemisorption stages of treatment, a deeper degree of removal of industrial pollutants from wastewaters is attained. The chemisorption stage allows stabilizing the treatment process in different concentration-temperature drops and increasing the degree of removal of synthetic surfactants (SSF), petroleum products, and nitrogen compounds. The possibility of regulating the selectivity of the treatment process by varying the composition of the chemisorption material is demonstrated.     

Colloidal processing of polymer ceramic nanocomposite integral capacitors

Polymer ceramic composites form a suitable material system for low temperature fabrication of embedded capacitors appropriate for the MCM-L technology. Improved electrical properties such as permittivity can be achieved by efficient filling of polymers with high dielectric constant ceramic powders such as lead magnesium niobate-lead titanate (PMN-PT) and barium titanate (BT). Photodefinable epoxies as the matrix polymer allow fine feature definition of the capacitor elements by conventional lithography techniques. The optimum weight percent of dispersant is tuned by monitoring the viscosity of the suspension. The dispersion mechanism (steric and electrostatic contribution) in a slightly polar solvent such as propylene glycol methyl ether acetate (PGMEA) is investigated from electrophoretic measurements. A high positive zeta potential is observed in the suspension, which suggests a strong contribution of electrostatic stabilization. By optimizing the particle packing using a bimodal distribution and modified processing methodology, a dielectric constant greater than 135 was achieved in PMN-PT/epoxy system. Suspensions are made with the lowest PGMEA content to ensure the efficiency of the dispersion and efficient particle packing in the dried film. Improved colloidal processing of nanoparticle-filled epoxy is a promising method to obtain ultra-thin capacitor films (<2/spl mu/m) with high capacitance density and improved yield. Capacitance of 35 nF/cm/sup 2/ was achieved with the thinnest films (2.5-3.0 /spl mu/m).     

Reactions Between Ingredients in Binary Silicate Glasses

It is demonstrated that the density of binary glasses upon variation of the molar content of the modifier in their compositions obeys a parabolic dependence, whose parameters can be used to estimate the extent and type of reactions between the components. The reaction parameters in glasses that are prone to liquation are lower by an order of magnitude and have the negative sign.     

Effect of the oxide support on the propane ammoxidation with Sb–V–O-based catalysts

The role of Nb₂O₅ and γ-Al₂O₃ oxide supports on the ammoxidation of propane on supported mixed Sb–V oxide at different Sb+V surface coverages is studied. Sb and V oxide species on alumina and on niobia support show different structural features that reflect in different performance during the ammoxidation of propane to acrylonitrile. Niobia-supported catalysts are much more selective to acrylonitrile than alumina-supported ones. Alumina interacts weakly with the supported oxides while niobia forms new phases through solid state reactions with the supported oxides during catalytic operation that must account for its higher selectivity values towards acrylonitrile and higher specific rate of acrylonitrile formation per vanadium site.     

An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement

The work describes various physical and chemical treatments to eliminate the deleterious effects of impurities in phosphogypsum on the delayed setting time and impaired strength development behaviour of cement to which it was added as a set regulator. The physical treatments included washing, milling, and ultrasonic treatment of the material, while the chemical treatments dealt with acidic and basic additions to the phosphogypsum during the washing stage. It was found that chemical treatment with a milk of lime solution, which is often recommended in literature, was ineffective in reducing set retardation. Treatment with ammonium hydroxide or sulphuric acid was more effective in this regard. Intergrinding phosphogypsum with slaked lime improved its effectiveness in reducing set retardation, but the use of unslaked lime was less effective and also resulted in marked reductions in compressive strengths. A combined treatment of wet milling phosphogypsum with a lime slurry in a ball mall was derived from these experiments and is recommended for full-scale plant applications.     

Tuning the Dimensions of C60‐Based Needlelike Crystals in Blended Thin Films

A new ordered structure of the C₆₀ derivative PCBM ([6‐6]‐phenyl C₆₁‐butyric acid methyl ester) is obtained in thin films based on the blend PCBM:regioregular P3HT (poly(3‐hexylthiophene)). Rapid formation of needlelike crystalline PCBM structures of a few micrometers up to 100 μm in size is demonstrated by submitting the blended thin films to an appropriate thermal treatment. These structures can grow out to a 2D network of PCBM needles and, in specific cases, to spectacular PCBM fans. Key parameters to tune the dimensions and spatial distribution of the PCBM needles are blend ratio and annealing conditions. The as‐obtained blended films and crystals are probed using atomic force microscopy, transmission electron microscopy, selected area electron diffraction, optical microscopy, and confocal fluorescence microscopy. Based on the analytical results, the growth mechanism of the PCBM structures within the film is described in terms of diffusion of PCBM towards the PCBM crystals, leaving highly crystalline P3HT behind in the surrounding matrix.