Effect of Contact Residual Stress Relaxation on Fracture Strength of Indented Soda-Lime Glass

The strength of Vickers-indented soda-lime glass measured in air at room temperature steadily increases with time after indentation, whereas optical retardation steadily decreases in the same interval. Annealing after indentation causes further strength increase and retardation decrease. The results are consistent with Marshall and Lawn's treatment of the slow crack growth of indentation flaws driven by the combined influence of residual contact stress and applied stress. Post-indentation strengthening of indentation flaws can be explained without recourse to flaw blunting.     

Synthesis of Si3N4 with Emphasis on Si-S-N Chemistry

Industrial production of Si₃N₄ from SiCI₄, is increasing. An element rivaling CI in abundance and cheapness with potentially suitable chemistry for this application is sulfur. Thus, Si–S–N chemistry was investigated to determine its usefulness in producing Si₃N₄. Bifunctionality in S, as opposed to mono-functionality in CI, may allow special routes via polymers to become important.     

Segregation of Isovalent Impurity Cations at the Surfaces of MgO and CaO

Enthalpies of segregation for isovalent impurities in magnesium and calcium oxide as a function of surface concentration were calculated by using an atomistic computer simulation method. We have considered Be²⁺, Mg²⁺, Ca²⁺, Ba²⁺, and Ni²⁺, segregating to both (001) and (110) faces. The results obtained can be extrapolated to predict the behavior of other impurities including Mn²⁺, Fe²⁺, and Co²⁺, We find, for example, that Fe²⁺, Mn²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ will concentrate at the (001) surface of MgO, while Ni²⁺ will be depleted. The enthalpy of segregation is found to vary substantially with coverage particularly for the larger impurities. The enthalpy becomes less negative with increasing impurity concentration due to the increasing lattice strain until the surface is nearly saturated. Then additional stabilization is obtained by restructuring of the surface layer. We predict reconstructed surfaces for both the (001) and (110) faces, which contain a high concentration of a larger impurity ion. The enthalpy of segregation shows a maximum at around 50% surface coverage implying a bimodal surface distribution of segregant. The influence of segregation on surface energy suggests two unusual effects. The (001) surface energy of the impure crystal becomes negative for surface concentrations of impurity greater than 10% Ba²⁺ or 75% Sr²⁺ in MgO. This implies a thermodynamic barrier to sintering. At high coverages of Ba²⁺ in MgO the (110) surface becomes more stable than the (001) face suggesting that facetting may occur.     

Parameter-Free Equation-of-State Calculations for MgO and ZrO2

The electronic band structure of ZrO₂ is calculated for the fluorite structure using the self-consistent augmented-plane-wave method in the muffin-tin approximation. The crystal charge density is then site decomposed by fitting Slater orbitals to the wave functions in the muffin tins. The resultant charge densities for Zr⁴⁺ and O²⁻ are then used in the Gordon-Kim method to derive pair potentials, from which a number of structural, elastic, and thermodynamic properties are calculated and compared with experimental results and similar calculations for MgO.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

A test for the statistical significance of DNA sequence similarities for application in databank searches

A method is developed, based on word-searching, which provides a rapid test for the statistical significance of DNA sequence similarities for use in databank searching. The method makes allowance for the lengths and dinucleotide compositions of the sequences being compared. A way is also described to calculate the power of the test, i.e. the probability of detecting a given similarity as being statistically significant. The effects on the power of the test of the scoring method, word length, sequence length, and sequence composition are examined. A novel scoring method is shown to be superior to the method currently used in most word-searching algorithms.     

A prolog based expert system for the allocation of quality assurance program resources

The worldwide proliferation of fraudulent materials has brought about the need for a new approach to the control of purchased material quality. Nuclear power, defense, aerospace and many other industries are affected by the supply of poor quality clones that presume to be original replacement parts. Safety considerations abound as these highly defective materials are used in systems that are critical to the preservation of human lives. Commonly utilized quality assurance programs have not effectively stopped the influx of fraudulent materials. These programs fail to concentrate inspection efforts on materials and inspection attributes that would effectively prevent the acceptance of fraudulent materials. herein a solution is presented to this problem in the form of an expert system application. Information commonly available in industry is formulated into a knowledge based system wherein advisories are given to the user regarding key purchased material receipt inspection strategies.