Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

Work of fracture of high impact polystyrene (HIPS) film under plane stress conditions

Essential work of fracture methodology was used to determine plane-stress ductile fracture toughness of high impact polystyrene film of thickness 0.26 mm. Results obtained indicated that specific essential work of fracture, w _e, is independent of loading rate, and for certain specimen sizes, independent of both gauge length and width of the specimen. On the other hand, w _e was found to be affected by the temperature, molecular anisotropy and the geometry of the test specimens. Reasonable estimate of w _e was obtained via crack opening displacement value.     

A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

Untersuchung der Verteilung und Intensität filamentierter Barrierenplasmen für die Behandlung von Oberflächen

The application of barrier discharges at atmospheric pressure in air expands on the market of plasma technology, because it is an ecological and cost‐effective alternative to other processes of surface treatment. These plasmas usually consist of a multitude of spatially and temporally localized filaments, whose distribution should be as even as possible for homogeneous treatment. This holds especially for the plasma treatment of sensitive goods such as wool or other textiles. In equipment for continuous pass of material the barrier arrangements often consist of a system cylinder – cylinder or cylinder – plane, whereby the gap width changes locally. Space distribution and intensity of filaments has been investigated by means of short‐time photography and spatially resolved measurement of current distribution and energy distribution derived from it. The local dependency found can be explained by means of a capacitive equivalent circuit.     

Robust vector control of induction motors using full-order observer in consideration of core loss

This paper proposes a method for designing a robust full-order observer for vector-controlled induction motors taking core loss into account. Although conventional research focuses on parameter identification, global stability of the identification remains questionable. Therefore, robustness against some parameters is required. This paper describes the design of a robust full-order observer which takes core loss into account, using both the gain-scheduled H/sub /spl infin// control and the linear matrix inequality technique. This design always results in a stable controller. The robustness of the proposed method against variations of resistances is evaluated by experiments.     

Assessing stem cell research productivity

Honour Index (HoI), a method to evaluate research performance within different research fields, was derived from the impact factor (IF). It can be used to rate and compare different categories of journals. HoI was used in this study to determine the scientific productivity of stem cell research in the Asian Four Dragons (Hong Kong, Singapore, South Korea and Taiwan) from 1981 to 2001. The methodology applied in this study represents a synthesis of universal indicator studies and bibliometric analyses of subfields at the micro-level. We discuss several comparisons, and conclude the developmental trend in stem cell research for two decades. This revised version was published online in August 2006 with corrections to the Cover Date.     

Micro-prober for wafer-level low-noise measurements in MOS devices

Low-frequency noise measurements represent an interesting investigation technique for the characterization of the quality and reliability of microelectronic materials and devices. Performing meaningful noise measurements at low and very low (f<1 Hz) frequencies, however, may be quite challenging, particularly because of the many sources of interference that superimpose on the noise signal. For this reason, packaged samples are preferred because they allow accurate shielding from the external environment, and because keeping the sample in close proximity to the low-noise biasing system and amplifier reduces microphonic and electromagnetic disturbances. Notwithstanding this, the possibility of performing low-frequency noise measurements at wafer level would be quite interesting, both because of the ease of obtaining wafer-level samples from industries with respect to packaged samples, and because this would avoid possible packaging-process induced device degradation. The purpose of this work is to demonstrate that it is, in fact, possible to design and build a dedicated probe system for performing high-sensitivity, low-frequency noise measurements on metal-oxide-semiconductor devices at wafer level.     

A comparison of transformation methods for evaluating two‐dimensional weakly singular integrals

Accurate numerical evaluation of integrals arising in the boundary element method is fundamental to achieving useful results via this solution technique. In this paper, a number of techniques are considered to evaluate the weakly singular integrals which arise in the solution of Laplace's equation in three dimensions and Poisson's equation in two dimensions. Both are two‐dimensional weakly singular integrals and are evaluated using (in a product fashion) methods which have recently been used for evaluating one‐dimensional weakly singular integrals arising in the boundary element method. The methods used are based on various polynomial transformations of conventional Gaussian quadrature points where the transformation polynomial has zero Jacobian at the singular point. Methods which split the region of integration into sub‐regions are considered as well as non‐splitting methods. In particular, the newly introduced and highly accurate generalized composite subtraction of singularity and non‐linear transformation approach (GSSNT) is applied to various two‐dimensional weakly singular integrals. A study of the different methods reveals complex relationships between transformation orders, position of the singular point, integration kernel and basis function. It is concluded that the GSSNT method gives the best overall results for the two‐dimensional weakly singular integrals studied. Copyright © 2002 John Wiley & Sons, Ltd.