Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

Application of novel extractants for actinide(III)/ lanthanide(III) separation in hollow-fibre modules

Separation tests using hollow-fibre modules were performed for the difficult selective extraction of trivalent actinides over fission lanthanides from acidic media. This article shows that with 2,6-di(5,6-dipropyl-1,2,4-triazin-3-yl)pyridine as the extractant, up to 94% americium could be extracted from 1.0 kmol/m³ HNO₃, with minimal lanthanide co-extraction. Using a synergistic mixture of bis(chlorophenyl)dithiophosphinic acid and tri-n-octyl phosphine oxide, tests were performed on extraction, lanthanide scrubbing and stripping. In the extraction test, up to 99.99% americium could be extracted from 0.5 kmol/m³ HNO₃, with approximately one third of the lanthanides being co-extracted. Mass transfer calculations using a consistent set of input data showed good agreement with the experiments.     

Development and commissioning of decision support tools for sewerage management.

Managing sewerage systems is a highly complex task due to the dynamic nature of the facilities. Their performance strongly depends on the know-how applied by the operators. In order to define optimal operational settings, two decision support tools based on mathematical models have been developed. Moreover, easy-to-use interfaces have been created as well, aiding operators who presumably do not have the necessary skills to use modelling software. The two developed programs simulate the behaviour of both wastewater treatment plants (WWTP) and sewer network systems, respectively. They have essentially the same structure, including raw data management and statistical analysis, a simulation layer using the application programming interface of the applied software and a layer responsible for the representation of the obtained results. Four user modes are provided in the two software including the simulation of historical data using the applied and novel operational settings, as well as modes concerning prediction of possible operation periods and updates. Concerning the WWTP software, it was successfully installed in Nantes (France) in June 2004. Moreover, the one managing sewer networks has been deployed in Saint-Malo (France) in January 2005. This paper presents the structure of the developed software and the first results obtained during the commissioning phase.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

RF microelectronics for W-CDMA mobile communication systems

Third generation (3G) mobile communication systems are now just starting to be introduced. With a maximum data rate of 2 Mbit/s they will make wireless access to broadband data services like the Internet or video applications feasible. Most of the different physical layer technologies summarised under the acronym 3G are based on wideband-CDMA (W-CDMA), in contrast to existing second generation systems, which mostly use TDMA and FDMA. This has severe consequences for the design of the transceiver front-ends. During standardisation these were assumed to have an adequate RF performance yet they still present a performance bottleneck for the system. Starting with a short introduction to UMTS (Universal Mobile Telecommunications System)-the 3G standard to be deployed in Europe and already operating in Japan-this paper describes by way of example some of the test cases specified for UMTS and their impact on the analogue front-end. It is shown that accurate simulation of all the analogue and digital signal processing is necessary in order to predict the RF performance needed of today's commercial RFICs. The paper then presents and reviews some actual design examples. Finally, possible technologies and techniques for application in future mobile terminals are discussed     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

Near-field corrections to site attenuation

The theoretical model used for calculating normalized site attenuation for broadband antennas in ANSI C63.4-1992 and for antenna calibration in ANSI C63.5-1988 includes only the radiation terms in the electric field. The omission of the near field terms leads to errors of as much as 2.0 dB at 30 MHz for horizontally polarized antennas separated by 3 m. Corrected values of normalized site attenuation and E _D^max are presented for the 30-300 MHz frequency range     

A base-band NDS electrode configuration for HACT devices

Heterostructure Acoustic Charge Transport (HACT) devices have been fabricated with a new nondestructive sense (NDS) electrode structure that provides for the recovery of base-band signals without the use of an integrating capacitor. This electrode structure provides an output signal comprising an RF carrier at the SAW frequency, amplitude modulated by the sampled input signal which has been delayed by a period proportional to the output electrodes distance from the input diode. The output of the NDS electrode structure is subsequently demodulated to provide the base-band signal     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.