A digital wind gust recorder

The instrument was a byproduct of an undergraduate final year project on wind power which was carried out by the Department of Mechanical Engineering of the University of Liverpool.The windmill test site was on an exposed, rocky island where there was no history of weather recording but a long tradition of violent winds.Field experience during the winter months suggested that corrosion fatigue arising from wind buffeting and salt spray would rank equally with maximum wind pressure as criteria of failure and if modern materials, so convenient for forming aerodynamic surfaces, were to be used then limited life concepts would need to be considered. This called for more knowledge of wind variations at the test site. A complete wind spectrum taken on chart recording instruments would have been ideal but since such such refined devices were not available the instrument to be described was designed.The only wind measuring instrument which was available was a rotating cup anemometer. This supplied an alternating voltage proportional to its rotational speed. It also operated a gear driven microswitch which could give an integrated “miles of wind” reading on an electromagnetic counter.Briefly the e.m.f. generated by the anemometer (Fig. 1) was matched against a pre-set voltage corresponding to the required gust velocity. When this was exceeded an appropriate counter was operated. Only the rising e.m.f. was significant. The subsequent fall was ignored. Initially three stages were incorporated which reported the gusts rising through forty, fifty and sixty knots, respectively. These recorded on separate counters. All basic settings were based on pitot-static speed determinations in a wind tunnel.     

Application of GaN-based ultraviolet-C light emitting diodes--UV LEDs--for water disinfection

GaN-based ultraviolet-C (UV-C) light emitting diodes (LEDs) are of great interest for water disinfection. They offer significant advantages compared to conventional mercury lamps due to their compact form factor, low power requirements, high efficiency, non-toxicity, and overall robustness. However, despite the significant progress in the performance of semiconductor based UV LEDs that has been achieved in recent years, these devices still suffer from low emission power and relatively short lifetimes. Even the best UV LEDs exhibit external quantum efficiencies of only 1-2%.The objective of this study was to investigate the suitability of GaN-based UV LEDs for water disinfection. The investigation included the evaluation of the performance characteristics of UV LEDs at different operating conditions as well as the design of a UV LED module in view of the requirements for water treatment applications. Bioanalytical testing was conducted using Bacillus subtilis spores as test organism and UV LED modules with emission wavelengths of 269 nm and 282 nm.The results demonstrate the functionality of the developed UV LED disinfection modules. GaN-based UV LEDs effectively inactivated B. subtilis spores during static and flow-through tests applying varying water qualities. The 269 nm LEDs reached a higher level of inactivation than the 282 nm LEDs for the same applied fluence. The lower inactivation achieved by the 282 nm LEDs was compensated by their higher photon flux. First flow-through tests indicate a linear correlation between inactivation and fluence, demonstrating a well designed flow-through reactor. With improved light output and reduced costs, GaN-based UV LEDs can provide a promising alternative for decentralised and mobile water disinfection systems.     

Toxic metals in the atmosphere in Lahore, Pakistan

Aerosol mass (PM₁₀ and PM_2.5) and detailed elemental composition were measured in monthly composites during the calendar year of 2007 at a site in Lahore, Pakistan. Elemental analysis revealed extremely high concentrations of Pb (4.4 μg m^− 3), Zn (12 μg m^− 3), Cd (0.077 μg m^− 3), and several other toxic metals. A significant fraction of the concentration of Pb (84%), Zn (98%), and Cd (90%) was contained in the fine particulate fraction (PM_2.5 and smaller); in addition, Zn and Cd were largely (≥ 60%) water soluble. The 2007 annual average PM₁₀ mass concentration was 340 μg m^− 3, which is well above the WHO guideline of 20 μg m^− 3. Dust sources were found to contribute on average (maximum) 41% (70%) of PM₁₀ mass and 14% (29%) of PM_2.5 mass on a monthly basis. Seasonally, concentrations were found to be lowest during the monsoon season (July-September). Principle component analysis identified seven factors, which combined explained 91% of the variance of the measured components of PM₁₀. These factors included three industrial sources, re-suspended soil, mobile sources, and two regional secondary aerosol sources likely from coal and/or biomass burning. The majority of the Pb was found to be associated with one industrial source, along with a number of other toxic metals including As and Cr. Cadmium, another toxic metal, was found at concentrations 16 times higher than the maximum exposure level recommended by the World Health Organization, and was concentrated in one industrial source that was also associated with Zn. These results highlight the importance of focusing control strategies not only on reducing PM mass concentration, but also on the reduction of toxic components of the PM as well, to most effectively protect human health and the environment.     

Trace-metal concentrations in normal human liver: methods to cope with marked variability

Concentrations of trace elements in human tissues characteristically vary widely, and the distributions of most concentrations are skewed to the right. Examination of some of the factors which contribute to the marked variability and skewness of the concentrations revealed that: (1) distributions of concentrations are satisfactorily normal (Gaussian) after logarithmic transformation, (2) ash weight is the best frame of reference in which to report results, (3) the distributions of metal concentrations are not further normalized by adjustments which assume that tissue lipid or collagen contains a fixed fraction of the metal found in the parenchyma, and (4) the choice of sample site within the liver is of minimal significance.     

Microanalysis of anionic surfactants in waste water by infrared spectroscopy

Infrared spectroscopy was applied to identify and determine microamounts of anionic surfactants contained in sewage or river waters. The surfactants tested were linear alkylbenzene sulfonate (LAS), branched alkylbenzene sulfonate (ABS), alpha olefine sulfonate (AOS), fatty alcohol sulfate (AS) and fatty alcohol ethoxy sulfate (AES).Anionic surfactants in waters were extracted by chloroform as methylene blue complexes and sulfate type surfactants, i.e. AS and AES were then removed by subsequent hydrolysis. Residual sulfonate type surfactants were first released from methylene blue complexes by ion exchange technique and then changed to sulfonyl chloride derivatives for infrared spectroscopy. Key bands for the identification of sulfonate type surfactants are 640, 618 and 524 cm⁻¹ for LAS, ABS and AOS, respectively. Sulfate type surfactants was calculated from the difference of methylene blue active substance contents before and after hydrolysis.     

Impact wave propagation in tall buildings using advanced spectral element method

One of the major divisions in analysis and design of tall buildings is to account for forces induced by flying‐object impact and the subsequent progressive collapse. During the past three decades, problems of contact mechanics have been considered by some authors, and special attention has been devoted to high‐speed impact. Impact wave propagation in tall buildings may be analysed using the conventional finite element method. However, in order to guarantee stability and accuracy of the solution, the number of elements used to model the structure may be very large indeed; more precisely, accurate results can be obtained after a substantial computational effort. In this respect, an improved complex spectral element method is developed for analysing the wave propagation problems in large structures. The purpose of this paper is to obtain the resulting dynamic responses of a tall building induced by a high‐speed impact of a flying object. Copyright © 2003 John Wiley & Sons, Ltd.     

Seismic methods for study of soil building properties

Bulletin of Engineering Geology and the Environment - Information about distribution of elastic wave propagation velocities Vp, Vs in the subsurface zone of a soil mass can be obtained rapidly and...     

Thermorheological model of a frozen-soil continuum

A method of evaluating the stress-strain state of frozen soils, which takes into account the existence of elastoviscoplastic and temperature deformations over time under variable external effects, is described. Translated from Osnovaniya, Fundamenty i Mekhanika Gruntov, No. 4, pp. 10–13, July–August, 1997.     

Long-term geophysical observations on the inguri dam rock foundation

Bulletin of Engineering Geology and the Environment - It has been found that during construction of the dam, prior to the filling of the reservoir, compaction and loading of the rocks under the...