Fabrication of Barium Strontium Titanate (Ba0.6Sr0.4 TiO3) 3D Microcomponents from Aqueous Suspensions

This study reports on the fabrication of BST (Ba_0.6Sr_0.4TiO₃)‐based 3D microcomponents through an aqueous colloidal approach. The BST powder was synthesized by solid‐state reaction assisted by thermal analysis and XRD diffraction. Well crystalline cubic BST single phase was obtained upon heat‐treating the precursor powder mixture at 1200°C–1250°C. The reactivity of the BST powder toward water was evaluated by the changes in pH and concentration of leached ionic species along aging time. Hydrolysis reactions were suppressed by chemisorbing a suitable phosphate‐based protective agent and enabled an excellent dispersion ability to be achieved. Aqueous suspensions with solids loadings as high as 50 vol% that are stable against hydrolysis for several days could easily be prepared from the surface‐treated BST powder in aqueous solutions of an epoxy resin. After adding a suitable hardener, the colloidal suspensions could easily be cast into soft silicon rubber molds to obtain homogeneous and high dense green BST bodies.     

Low Cost Porous Alumina with Tailored Microstructure and Thermal Conductivity Prepared using Rice Husk and Sucrose

This study demonstrates a cost‐effective way to fabricate porous ceramics with tailored porosity and pore microstructure using 5–40 wt% rice husk (RH) in <75 μm, 75–180 μm, 180–355 μm, 355–420 μm, and 420–600 μm size, as pore former. Sucrose, used as binder, also acted as a pore former. Porous alumina compacts with 20%–66% volume fraction porosity and 50–516 μm pore size (length) were successfully fabricated. Microstructure of samples reveal randomly oriented elongated coarse pores and fine pores (avg. size 4 μm), created during burnout of RH and sucrose, respectively. Samples with isolated and/or interconnected pores were fabricated using this process. Thermal conductivity of the samples prepared was measured using Transient Plane Source (TPS) technique. Thermal conductivity ranges from 1.2 to 24 W/mK. Experimental results agree closely with predictions made based on Effective Medium Theory (EMT) for a two‐phase system.     

面向Wi-Fi客户机的低端微控制器

随着各项标准得到充实,而且接入点越来越容易找到,面向Wi-Fi客户站中的低端处理器这一市场成为一个充满机会的奋斗目标。     

Recent advances for serial processes of hazardous chemicals in fully integrated microfluidic systems

The development and enlargement of toxic and hazardous chemicals are severely limited by health and safety concerns. We summarize studies on fully integrated micro-chemical systems and total processes to reduce accidental exposure to various regents that are toxic, explosive, or carcinogenic, which significantly improved the safety of work involving risky compounds. This review covers the leak-free continuous-flow processes of hazardous chemicals in fully integrated microfluidic systems, specially denoted as micro-total envelope systems (μ-TESs), that are conducting a serial process of the generation of hazardous reagents, in-situ purification and separation, subsequent reaction, and product isolation with improved efficiencies. These attempts suggest safe and efficient tools and processes of useful but hazardous chemicals for researchers and manufacturing workers in the field of pharmaceutic discovery, natural products, biology as well as materials synthesis.     

Characterizations of surfactant synthesized from Jatropha oil and its application in enhanced oil recovery

Surfactants are frequently used in chemical enhanced oil recovery (EOR) as it reduces the interfacial tension (IFT) to an ultra‐low value and also alter the wettability of oil‐wet rock, which are important mechanisms for EOR. However, most of the commercial surfactants used in chemical EOR are very expensive. In view of that an attempt has been made to synthesis an anionic surfactant from non‐edible Jatropha oil for its application in EOR. Synthesized surfactant was characterized by FTIR, NMR, dynamic light scattering, thermogravimeter analyser, FESEM, and EDX analysis. Thermal degradability study of the surfactant shows no significant loss till the conventional reservoir temperature. The ability of the surfactant for its use in chemical EOR has been tested by measuring its physicochemical properties, viz., reduction of surface tension, IFT and wettability alteration. The surfactant solution shows a surface tension value of 31.6 mN/m at its critical micelle concentration (CMC). An ultra‐low IFT of 0.0917 mN/m is obtained at CMC of surfactant solution, which is further reduced to 0.00108 mN/m at optimum salinity. The synthesized surfactant alters the oil‐wet quartz surface to water‐wet which favors enhanced recovery of oil. Flooding experiments were conducted with surfactant slugs with different concentrations. Encouraging results with additional recovery more than 25% of original oil in place above the conventional water flooding have been observed. © 2017 American Institute of Chemical Engineers AIChE J, 63: 2731–2741, 2017     

Effect of hydrophilic and hydrophobic cyclodextrins on the release of encapsulated allyl isothiocyanate (AITC) and their potential application for plastic film extrusion

Allyl isothiocyanate (AITC), a natural pungent flavor from wasabi and horseradish, is well-known antimicrobial agents against foodborne pathogens. However, its highly volatile nature and low thermal stability restrict its application in the food packaging industry. Also, its strong organoleptic characteristics hinder its application at a higher dosage. We encapsulated AITC in β-cyclodextrin (β-CD) and triacetyl-β-CD (TA-β-CD) and evaluated the performance as slow releasing active compounds through low-density polyethylene (LDPE)–cyclodextrins (CDs) matrix. Also, the thermal, optical, mechanical, and barrier properties of two ternary blends, LDPE/β-CD/AITC(L-CDs) and LDPE/TA-β-CD/AITC(L-TACDs), were investigated to compare their compatibility under the plastic extrusion process. During the 15 days of the storage period, L-TACDs maintained more consistent AITC release and a higher concentration than L-CDs. Also, the blending of LDPE and TA-β-CD was more compatible with that of LDPE and β-CD. No significant optical, mechanical, and barrier property changes were observed in LDPE with less than 3% of TA-β-CD while L-CDs showed substantial agglomeration on the ternary blend films and the lower mechanical and barrier properties than pure LDPE. The results indicate that the LDPE films containing TA-β-CD/AITC can be applied as an effective antimicrobial packaging material for food and nonfood applications. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48137.     

Kinetics study on cnt‐supported RuKCo FTS catalyst in a fixed bed reactor

The rate of syngas (H₂/CO) consumption over a RuKCo/CNT Fischer–Tropsch synthesis (FTS) catalyst was measured in a fixed bed microreactor at 210–225°C, 2–3.5 MPa, H₂/CO feed molar ratios of 1–2.5, and gas hourly space velocity (GHSV) range of 2700–3600 h^?1. The data have been used to model the kinetics of the FTS reactions within the range of the studied conditions. One empirical power law model and four semi‐empirical kinetic models based on Langmuir–Hinshelwood‐type equation have been evaluated. The best fitting was obtained with the equation: similar to that proposed by Brötz et al. The estimated activation energy (E = 80–85 kJ/mol) is lower than that is reported in the literature. The validity of these results are restricted to fixed beds with the given catalyst in the tested conversion regime.     

Multiobjective Optimization of Simulated Moving Bed Reactor and its Modification — Varicol Process

A comprehensive optimization study on a Simulated Moving Bed Reactor (SMBR) system is reported in this article for the direct synthesis of Methyl Tertiary Butyl Ether (MTBE). In addition, the SMB technology, which is based on synchronous switching of ports, was modified to a new more flexible Varicol process based on non‐synchronous switching. Multi‐objective optimization has been performed for both SMBR and Varicol and their efficiencies were compared. A state‐of‐the‐art optimization technique, viz., Non‐dominated Sorting Genetic Algorithm (NSGA) that allows handling of these complex optimization problems is employed in this study.