Preparation and photoconduction of rapidly quenched films in the Bi2O31bM2O5 system (M=V,Nb and Ta)

The Bi₂O₃1bM₂O₅ films (M=V, Nb and Ta) were prepared by a rapid quenching technique using a twin-roller type equipment. Quenched film of pure Bi₂O₃ partially precipitated a tetragonal phase which differs from well-known β-Bi₂O₃ in structure. In every (Bi₂O₃)_0.975 (M₂O₅)_0.025 composition (2.5% M₂O₅), the tetragonal phase was obtained as single phase, and the tetragonality became greater than that of the pure Bi₂O₃. Beyond this composition, the tetragonality decreased to form δ-phase with a fcc structure with increasing the M₂O₅ content. The lowest V₂O₅ content forming a δ-phase was 5%, while a slight tetragonality still remained in the samples containing 10% Nb₂O₅ and 10% Ta₂O₅, respectively. From the measurement of the photoconductivities of the quenched films, it was proved that a photoconduction appeared in the tetragonal phase while no photoconductivity was observed in the cubic phase. The characteristic of the photoconduction was that a remarkable decrease in the resistivity was observed when a light of ca. 500 nm in wave length was irradiated on the films.     

The oxidation properties of fourth generation single-crystal nickel-based superalloys

The fourth-generation nickel-based single-crystal superalloys, which contain large amounts of refractory metals for strengthening and platinum group metals for topologically close-packed phase prevention, show excellent high-temperature strength. However, these alloying elements seem to decrease high-temperature oxidation resistance. In this study, nickel-based superalloys with various amounts of tantalum, rhenium, and ruthenium were examined in isothermal and cyclic exposures at 1,100°C to investigate the effect on the oxide growth rate and resistance to scale spallation. Ruthenium and rhenium were found to degrade the oxidation resistance by the vaporization of their oxide. Tantalum-rich oxide in the spinel layer acts to stabilize ruthenium and rhenium oxide in the scale. The addition of hafnium and yttrium is effective in improving the oxidation resistance of ruthenium-containing nickel-based superalloys.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Stability of large-scale coal-fired MHD channels

Stability of large-scale coal-fired MHD channels is studied by (1) linearized stability analysis, and (2) time-dependent 1-D analysis. The channel length is 15 m with 600 electrode pairs, and the output power ranges from 220.6 MW through 258.7 MW. Linearized stability analyses show that the Faraday channels operated with fixed loading resistance are stable, whereas the two waves of u and u–a (u, a: gas and sound velocity) become unstable in the Faraday channel with fixed loading factor. Two waves of u and u–a are unstable in the diagonal channel with fixed loading current and the u + a wave becomes unstable in the diagonal channel with fixed electrode current. Time-dependent one-dimensional analyses indicate that the Faraday channels with fixed load resistance are smooth without growth of fluctuation. The diagonal channels with fixed electrode current are smooth with no fluctuation, though the linear theory indicates that the u + a wave is unstable. The diagonal channel with fixed load current suffers large disturbance along the latter half of the channel, being consistent with the linearized analysis which indicates that the u - a and u waves are unstable.     

Chemical processing and characterization of spinel-type thermistor powder in the Mn-Ni-Fe oxide system

The coprecipitated Mn-Ni-Fe oxalate was prepared from the mixed sulfate solution by optimum pH control. The chemical composition agreed well with that of the starting solution, and the thermal decomposition of the Mn-Ni-Fe oxalate in air below 600 °C led to the direct formation of cubic spinel phase with fine particle size. The sinterability of the calcined powder, the stability of cubic spinel phase and the influence of annealing temperature on electrical properties of the sintered bodies, were investigated.     

Development of a dual‐lamp projector with higher brightness

Stationary projectors mainly used in system applications have recently gained a wider application range, including general presentations in halls and large conference rooms and being used, for example, in digital signage and for monitoring purposes. Consequently, they are required to meet new market demands for durability, reliability, and flexibility in installation in addition to their conventional basic performance such as especially high brightness. To achieve especially high brightness, a new optical system with two lamps is proposed; the profile of the cover glass that prevents the glass from scattering is made aspherical, the profile of the beam‐combining mirror is improved with its position optimized, and the size of the incident plane of the integrator rod is made larger (1.1 times). These measures resulted in an optical system of an even higher efficiency with 7000 lm, which is the highest in its class (according to a June 2010 investigation). Also, the arrangement of two parallel lamps completely eliminated the effect of heat passing from one lamp to the other, which helped secure durability, reliability, and flexibility in installation. Furthermore, the combined use of the unique non‐telecentric optical system, adopted from the conventional single‐lamp model, helps maintain the class‐highest contrast ratio.^1,2     

A dynamic Houjin (square) and a symmetric Houjin

A Houjin is an n by n square lattice with each cell containing a symbol (such as a number or a letter). Further, these numbers or letters are designed to exhibit symmetry. For example, a magic square is a Houjin where the embedded symmetry is that the numbers in each row, column, and a center diagonal have an equal sum. This article reports a new Houjin: a dynamic Houjin. A dynamic Houjin changes its numbers at each time step while satisfying the symmetry as a Houjin (a magic square). The dynamic Houjin has a further symmetry in a time dimension, i.e., the sums of the numbers in each cell are identical.     

Isotactic polypropylene hollow microfibers prepared by CO2 laser‐thinning

An isotactic polypropylene hollow microfiber was continuously produced by using a carbon dioxide (CO₂) laser‐thinning method. To prepare the hollow microfiber continuously, the apparatus used for the thinning of the solid fiber was improved so that the laser can circularly irradiate to the hollow fiber. Original hollow fiber with an outside diameter (OD) of 450 μm and an internal diameter (ID) of 250 μm was spun by using a melt spinning machine with a specially designed spinneret to produce the hollow fiber. An as‐spun hollow fiber was laser‐heated under various conditions, and the OD and the ID decreased with increasing the winding speed. For example, when the hollow microfiber obtained by irradiating the CO₂ laser to the original hollow fiber supplied at 0.30 m min^?1 was wound up at 800 m min^?1, the obtained hollow microfiber had an OD of 6.3 μm and an ID of 2.2 μm. The draw ratio calculated from the supplying and the winding speeds was 2667‐fold. The hollow microfibers obtained under various conditions had the hollowness in the range of 20–30%. The wide‐angle X‐ray diffraction patterns of the hollow microfibers showed the existence of the highly oriented crystallites. Further, the OD and ID decreased, and the hollowness increased by drawing hollow microfiber obtained with the laser‐thinning. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2600–2607, 2006     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002