Effects of heated seats in vehicles on thermal comfort during the initial warm-up period

Eight subjects participated in a subjective experiment of eight conditions to investigate the effects of heated seats in vehicles on skin temperature, thermal sensation and thermal comfort during the initial warm-up period. The experimental conditions were designed as a combination of air temperature in the test room (5, 10, 15, or 20 °C) and heated seat (on/off). The heated seat was effective for improving thermal comfort during the initial warm-up period when air temperature was lower than 15 °C. Use of heated seats prevented decreases in or increased toe skin temperature. Heated seats also increased foot thermal sensation at 15 and 20 °C. Optimal thermal sensation in contact with the seat was higher when air temperature was lower. Optimal skin temperature in contact with the seat back was higher than that with the seat cushion. Moreover, these optimal skin temperatures were higher when air temperature was lower.     

A coaxial pulsed plasma thruster using chemical propellants

Pulsed plasma thrusters (PPTs) have the advantages of mechanical simplicity and robustness compared to other electric propulsion systems. However the thrust power ratio of PPTs is lower than that of other electric propulsion systems. To enhance the thrust performance of the PPT, we propose to use several combustible solid chemicals as coaxial PPT propellants to replace Teflon^® (Polytetrafluoroethylene: PTFE). With the design, the force obtained thermodynamically is expected to augment the PPT thrust power ratio with the help of the chemical energy contained in the propellants. As a result, the thrust power ratio is increased using hydroxyl-terminated polybutadiene-ammonium perchlorate (HTPB-AP)-based propellants compared to the case of ordinary Teflon. The discharge current and voltage waveform does not change even when the propellant is changed. These findings could indicate that the impulse bits by gasdynamic contribution are lager in the case of chemical solid propellants than in the case of Teflon.     

Magnetization Reversal by Electrical Spin Injection in Ferromagnetic (Ga,Mn)As-Based Magnetic Tunnel Junctions

We report current-induced magnetization reversal in a ferromagnetic semiconductor-based magnetic tunnel junction (Ga,Mn)As/AlAs/(Ga,Mn)As prepared by molecular beam epitaxy on a p-GaAs(001) substrate. A change in magneto-resistance that is asymmetric with respect to the current direction is found with the excitation current of 10⁶ A/cm². Contributions of both unpolarized and spin-polarized components are examined, and we conclude that the partial magnetization reversal occurs in the (Ga,Mn)As layer having smaller magnetization with the spin-polarized tunneling current of 10⁵ A/cm².     

Mass recovery adsorption refrigeration cycle—improving cooling capacity

The study investigates the performance of two-bed, silica gel-water adsorption refrigeration cycle with mass recovery process. The cycle with mass recovery can be driven by the relatively low temperature heat source. In an adsorption refrigeration cycle, the pressures in adsorber and desorber are different. The chiller with mass recovery process utilizes the pressure difference to enhance the refrigerant mass circulation. Cooling capacity and coefficient of performance (COP) were calculated by cycle simulation computer program to analyze the influences of operating conditions. The mass recovery cycle was compared with conventional cycle such as the single stage adsorption cycle in terms of cooling capacity and COP. The results show that the cooling capacity of mass recovery cycle is superior to that of conventional cycle and the mass recovery process is more effective for low regenerating temperature.     

A novel polarizer‐free dye‐doped polymer‐dispersed liquid crystal for reflective TFT displays

Abstract— A novel preparation method for dichroic dye‐doped polymer‐dispersed liquid crystals has been developed. This was achieved by creating a porous polymer matrix first by washing out the liquid crystal from a polymer‐dispersed liquid crystal (PDLC), which is then refilled with dye‐doped liquid crystal. Optimizing the liquid crystal used in the refilling results in decreased turn‐on voltage and faster response time. Poster‐standard reflectivity and newspaper‐standard contrast was demonstrated with a 3.8‐in. QVGA reflective TFT display with a drive voltage of 10 V.     

Application of an ultrahigh-resolution scanning electron microscope (UHS-T1) to biological specimens

In 1985 we developed an ultrahigh-resolution scanning electron microscope with a resolution of 0.5 nm. It is equipped with a field emission gun and an objective lens with a very short focal length. In this study we report a survey of some different preparation techniques and biological specimens using the new scanning electron microscope. Intracellular structures such as cell organelles were observed surprisingly sharper than those observed by ordinary scanning electron microscopes. However, at magnifications over 250,000 X, platinum particles could be discerned as scattered pebbles on the surface of all structures in coated materials. Using an uncoated but conductively stained specimen, we successfully observed ribosomes on a rough endoplasmic reticulum at a direct magnification of 1 million. In these images some protrusions were recognized on the ribosomes. Ferritin and immunoglobulin G were used as samples of biological macromolecules. These samples were observed without metal coating and conductive staining. The ferritin particles appeared as rounded bodies without any substructure on the surface and immunoglobulin G as complexes of three-unit bodies. In the latter the central body might correspond to the Fc fragment and two side ones to Fab fragments. We assume that ultrahigh-resolution scanning electron microscopy is an effective means for observation of the cell fine structures and biological macromolecules. It will open a new research field in biomedicine.     

High temperature superconductor micro-superconducting-quantum-interference-device magnetometer for magnetization measurement of a microscale magnet

We have developed a high temperature superconductor (HTS) micrometer-sized dc superconducting quantum interference device (SQUID) magnetometer for high field and high temperature operation. It was fabricated from YBa2Cu3O7-delta of 92 nm in thickness with photolithography techniques to have a hole of 4x9 microm2 and 2 microm wide grain boundary Josephson junctions. Combined with a three dimensional magnetic field coil system, the modulation patterns of critical current Ic were observed for three different field directions. They were successfully used to measure the magnetic properties of a molecular ferrimagnetic microcrystal (23x17x13 microm3), [Mn2(H2O)2(CH3COO)][W(CN)8]2H2O. The magnetization curve was obtained in magnetic field up to 0.12 T between 30 and 70 K. This is the first to measure the anisotropy of hysteresis curve in the field above 0.1 T with an accuracy of 10(-12) J T(-1) (10(-9) emu) with a HTS micro-SQUID magnetometer.     

Relationship between particle erosion and lamellar microstructure for plasma-sprayed alumina coatings

The lamellar structure determines mechanical properties of a thermal spray coating. A model for the erosion of thermally sprayed ceramic coatings resulting from the debonding of flattened ceramic particles is proposed based on the examination of the erosion mechanism. The relationship between erosion rate and microstructural parameters is established both experimentally and theoretically to reveal main lamellar structural parameters controlling erosion of thermally sprayed ceramic coating. The microstructural parameters include the mean bonding ratio between lamellae and thickness of the lamellae. The erosion rate of plasma-sprayed Al₂O₃ coatings was measured at impact angle of 90° under the fixed erosion test conditions. The correlation of theoretical model with the observed structural parameters and erosion data of alumina coatings was examined. It is revealed that the theoretical relationship agreed well with the observed relation. The results clearly revealed that the erosion of plasma-sprayed ceramic coating was inversely proportional to the mean lamellar bonding ratio. The influences of spray parameters on erosion effected mainly through their influences on the lamellar bonding. The erosion resistance of a thermally sprayed ceramic coating was controlled by coating fracture toughness.     

A preparation method for observing intracellular structures by scanning electron microscopy

In order to observe intracellular structures by scanning electron microscopy, excess cytoplasmic matrix must be removed from the fractured surface of cells. Previously we reported an Osmium-DMSO-Osmium method devised for this purpose. This method is very effective in revealing intracellular structures, but requires osmium tetroxide for initial fixation with some consequent disadvantages. In the present study, a revised Osmium-DMSO-Osmium method is reported, in which an aldehyde mixture is used as the initial fixative instead of osmium tetroxide. As fixation is carried out by perfusion in this revised method, better preservation of fine structures is achieved than by the original method, especially in the central nervous tissue which tends to suffer from post-mortem degeneration. Moreover this method can be applied to cytochemical studies of intracellular structures with a scanning electron microscope (SEM). In this study, acid phosphatase of lysosomes is demonstrated in a coloured SEM micrograph.     

Hot Corrosion Behavior and Microstructural Change of Al-Gradient CoNiCrAlYSi Coatings, Produced by LVPS and Diffusional Processes

Conventional and gradient CoNiCrAlYSi coatings were produced by using low vacuum plasma spray and an additional step of diffusional over aluminizing (pack cementation) techniques on an Inconel-738 substrate. Hot corrosion of these coatings was investigated using Na₂SO₄–20wt%NaVO₃ molten salt at 880?°C for 800?h. Hot corrosion rate was determined by measuring the weight gain of the specimens at regular intervals for a duration of 20?h. X-ray diffraction, field emission scanning electron microscopy and electron probe micro analysis techniques were used to determine the nature of phases, investigation of the thermally grown oxide, examination of the surface attack and determination of the elemental distribution. The gradient coating showed better performance by re-healing alumina scale due to its possession of more β phase as Al reservoir. Results indicated that pack cementation process caused an increase in amount of aluminum-rich β phase and better hot corrosion properties of gradient coatings owing to the Al enrichment in the outer layer and rapid formation of protective oxide on the surface.