Adaptation of drafting plotter for buried contact groove formation

Lasers (e.g. Nd-YAG) have been used extensively for groove formation both in laboratories and commercial production but the initial capital cost is high. The production throughput is also low and thus adds to the cost of the cell. To reduce cost and increase production throughput a drafting plotter has been adapted to serve as a mechanical scriber for groove formation. The adapted plotter can scribe cells in matrix form to reduce the human labour and increase the production throughput. The characterization of the scribing tips in conjunction with the plotter showed that the best yield for the scriber is obtained when the scribing tip is mounted at 78° to the stock. Of the seven characterized scribing tips, the 90° conical scriber has been found to give the same groove geometry as the laser. The application of the adapted plotter to cell fabrication did not show any significant deterioration in the electrical output parameters for the mechanically scribed cells when compared with laser scribed cells. This article reports the adaptation of the x-y table drafting plotter to form buried contact grooves.     

Surface modification and functionalization of electroactive polymer films via grafting of polyelectrolyte,polyampholyte and polymeric acids

Films of electroactive polymers, such as polyaniline (PAN) in its emeraldine base form, and poly(3-alkylthiophene), poly(3-hexylthiophene) (P6TH), poly(3-octylthiophene) (P8TH), and poly(3-dodecylthiophene) (P12TH) can be readily functionalized via thermal or near ultraviolet-light-induced surface graft copolymerization with monomers of polyelectrolyte, polyampholyte and polymeric acids. The monomers used in the present work include dimethyl sulphate quaternized dimethylamino-ethylmethacrylate (DMAEM·C₂H₆SO₄), 3-dimethyl(methacryloyloxyethyl)ammonium propane sulphonate (DMAPS), acrylic acid (AAc) and a sodium salt of styrene sulphonic acid (NaSS). The surface structures and compositions of the electroactive polymer films after functionalization via graft copolymerization were characterized by angle-resolved X-ray photoelectron spectroscopy. Graft copolymerization of poly(3-alkylthiophene) films, but not PAN films, with the hydrophilic monomers readily results in a stratified surface microstructure arising from the migration of the hydrophilic graft chains beneath a thin surface layer which is much richer in the substrate chains. On the other hand, graft copolymerization of PAN films with AAc and NaSS readily gives rise to a self-protonated (and thus conductive) surface structure.     

Geometric and algebraic errors in calculating a transducer'sspatial impulse response

Two types of errors resulting from the numerical evaluation of a transducer's spatial impulse response function have been identified, One is geometric and is due to the mismatch between the emulated piston surface (approximated using many small planar elements) and the true surface. The other error is algebraic and is due to the inexact formulation of the response of the emulated surface. The deviations from the true response were calculated for three different pistons. The results indicate that the shape and placement of the elements are important for the computational accuracy     

Biogas and biomass technology: Energy generation from biomass and waste in the Netherlands

Within the European Community, the interest in energy generation from biomass and waste is increasing. A brief overview is given of several thermal conversion technologies, of biomass production and waste availability in the Netherlands. Based on this, the possibilities for energy generation from biomass and waste in the Netherlands are evaluated.     

Charge-based capacitance measurements (CBCM) on MOS devices

A new simple method of measuring capacitance-voltage characteristics of MOS devices is presented. Proceeding from the charge-based capacitance measurement technique suggested recently, a compact test structure with high resolution has been developed, which only requires measurement of do quantities. The method was tested on a 0.6-μm CMOS process with small and large area capacitors and compared to well-known high-frequency capacitance-voltage results. Beside using a reference structure, a second means of extracting parasitic effects is demonstrated for small structures. The test structure allows measurements in a wide frequency range with high accuracy and low noise contribution at small capacitance levels     

Influence of body segment dynamics on loads at the lumbar spine during lifting.

Flexion-extension moments acting at the L5/S1 level and hip joints were calculated using three different techniques; a pure static analysis, a static analysis including the inertial force of the load, and a dynamic analysis. Ten subjects participated in the study and were asked to lift a box weighing either 50 N or 150 N, using a freestyle technique. The lifts were performed at normal and fast speed. The intra-subject lifting techniques were consistent when lifting the same loads. The moments predicted by the dynamic analysis and the static analysis were the same when holding weights in static postures. When performing the lifts, differences in the peak moments occurred between static and dynamic analyses. These differences were influenced by external load and by lifting speed. Taking the effect of the inertia of load into account in the static analysis resulted in an increase in the moment magnitude, but the predicted moment was still much less than in the dynamic analysis which yielded the largest moment magnitudes. The difference between dynamic and static analysis was greatest when lifting 50 N at fast speed; an 87% increase in L5/S1 moment and a 95% increase in hip moment was observed when replacing the pure static with a dynamic analysis.     

Computer processing of artifact and arrhythmias in heart rate variability analysis.

Analysis of heart rate variability (HRV) with Holter monitoring is often difficult due to excessive artifacts and arrhythmias. While short sudden surges are treated successfully by most methods, slow heart rate (HR) variations, nocturnal trapezoidally-shaped HR increases and special types of arrhythmias which are similar to normal HRV fluctuations may distort further time domain and spectral analysis. This paper examines the advantages and disadvantages of different methods for preprocessing of HR data. We have developed the following approach to the analysis of HRV. (1) A combination method based on the absolute difference between HR values and both the last normal HR value and an updated mean is used for removal of artifacts and arrhythmias. This method can detect both sudden surges in HR values as well as longer periods of noise combined with slow normal variations. An additional stage of wild point removal is then optionally applied. (2) Certain special problems such as large T-waves, bigeminal rhythm, slow HR variations and nocturnal trapezoidally-shaped HR increases are also identified. Although none of the algorithms can be applied successfully to all cases, the final computer analysis for preprocessing described in the present study has proved to be superior to the simplified methods which are usually used and provides more suitable data for HRV analysis.     

A typed functional extension of logic programming

A logic language is suitable for specification if it is equipped with features for data abstraction and modularization. In this paper, an effective mechanism to incorporate function and type into logic programming is presented as the means to embed data abstraction mechanism into logic programming. This incorporation is essentially based on Horn clause logic with equality and a polymorphic type system that is an extension of Mycroft and O’Keefe’s system. This paper also presents an implementation based on Warren Abstract Machine (WAM) and shows the performance, along with a comparison with WAM.     

Antennas and other electromagnetic applicators in biology andmedicine

Medical and biological applications of antennas can be classified into two broad groups: (1) therapeutic and (2) informational (including diagnostics and measurement of material electromagnetic (EM) properties). Most of these applications involve EM coupling into or out of the body which requires a device such as an antenna or other applicator. A common characteristic of many applications is the difficulty of coupling EM energy into the interior of the body without damaging the surface. Rapidly increasing computing power and new developments in numerical EM techniques are expected to have a great impact on the use of EM devices in medicine and biology