Bottom-contact small-molecule n-type organic field effect transistors achieved via simultaneous modification of electrode and dielectric surfaces

Low-voltage, n-type organic field effect transistors (OFETs) with simultaneously modified bottom-contact (BC) electrodes and dielectric were compared to their top-contact (TC) counterparts. The devices modified with 6-phenoxyhexylphosphonic acid (Ph6PA) self-assembled monolayer (SAM) showed similar performance, morphology, and contact resistance. Electron mobility of C₆₀ devices were 0.212 and 0.320 cm² V⁻¹ s⁻¹ and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) devices were 0.04 and 0.06 cm² V⁻¹ s⁻¹ for TC and BC devices, respectively. Low contact resistance between 11 and 45 kΩ cm was found regardless of device architecture or n-type semiconductor used. This work shows it is possible to fabricate solution processable low-voltage bottom-contact devices with performance that is similar or better than their top-contact counterparts without the addition of complex and time-consuming processing steps.     

Electrical impedance spectroscopy of the human prostate

Tissue electrical impedance is a function of its architecture and has been used to differentiate normal and cancer tissues in a variety of organs including breast, cervix, skin, and bladder. This paper investigates the possibility of differentiating normal and malignant prostate tissue using bioimpedance spectra. A probe was designed to measure impedance spectra over the range of 10 kHz to 1 MHz. The probe was fully characterized using discrete loads and saline solutions of different concentrations. Impedance spectra of five ex vivo prostates were measured in the operating room immediately following radical prostatectomy. Wilcoxon signed-rank tests were used to compare the normal and malignant findings. The impedance probe had a signal-to-noise ratio (SNR) > 84 dB across the entire spectrum and measured a tissue volume of approximately 46 mm(3). At 10 kHz, prostate conductivity (or) ranged from 0.232 S/m to 0.310 S/m for tumor and from 0.238 S/m to 0.901 S/m for normal tissue. At 1 MHz the ranges were 0.301 S/m to 0.488 S/m for tumor and 0.337 S/m to 1.149 S/m for normal. Prostate permittivity (epsilonr) ranged from 6.64 x10(4) to 1.25 x 10(5) for tumor and from 9.08 x 10(4) to 4.49 x 10(5) for normal tissues at 10 kHz. And, at 1 MHz the er ranges were 9.23 x 10(2) to 1.88 x 10(3) for tumor and 1.16 x 10(3) to 2.18 x 10(3) for normal tissue. Both sigma and epsilonr of tumor tissue were found to be significantly lower than that of normal tissue (P < 0.0001). Conductivity and permittivity are both higher in normal prostate tissues than they are in malignant tissue making them suitable parameters for tissue differentiation. This is in agreement with trends observed in other tissues reported in much of the literature. Expanded studies are needed to further validate this finding and to explore the biological mechanism responsible for generating the results.     

Anode Interfacial Tuning via Electron‐Blocking/Hole‐Transport Layers and Indium Tin Oxide Surface Treatment in Bulk‐Heterojunction Organic Photovoltaic Cells

The effects of anode/active layer interface modification in bulk‐heterojunction organic photovoltaic (OPV) cells is investigated using poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and/or a hole‐transporting/electron‐blocking blend of 4,4′‐bis[(p‐trichlorosilylpropylphenyl)‐phenylamino]biphenyl (TPDSi₂) and poly[9,9‐dioctylfluorene‐co‐N‐[4‐(3‐methylpropyl)]‐diphenylamine] (TFB) as interfacial layers (IFLs). Current–voltage data in the dark and AM1.5G light show that the TPDSi₂:TFB IFL yields MDMO‐PPV:PCBM OPVs with substantially increased open‐circuit voltage (V_oc), power conversion efficiency, and thermal stability versus devices having no IFL or PEDOT:PSS. Using PEDOT:PSS and TPDSi₂:TFB together in the same cell greatly reduces dark current and produces the highest V_oc (0.91 V) by combining the electron‐blocking effects of both layers. ITO anode pre‐treatment was investigated by X‐ray photoelectron spectroscopy to understand why oxygen plasma, UV ozone, and solvent cleaning markedly affect cell response in combination with each IFL. O₂ plasma and UV ozone treatment most effectively clean the ITO surface and are found most effective in preparing the surface for PEDOT:PSS deposition; UV ozone produces optimum solar cells with the TPDSi₂:TFB IFL. Solvent cleaning leaves significant residual carbon contamination on the ITO and is best followed by O₂ plasma or UV ozone treatment.     

EXIF-white balance recognition for image forensic analysis

Due to the lack of post-processing resistance, traditional forensic methods are vulnerable to cascade image manipulations, e.g. copy-and-paste operation followed by high compression. Different from these traditional methods, a new forensic method that has the ability to resist multiple types of post-processing, is proposed by using white balance from the EXchangeable Image File format (EXIF) header. We first extract image quality metrics between each two combination of one original image and twelve re-balanced images. By regularizing the eigen spectrum of image quality metrics, the compact set of image eigen features is then selected for recognizing different EXIF-white balance modes via the SVM classifier. The experimental results show that the proposed method has the ability to resist the influence of high compression or heavy downsampling in both theoretical and realistic scenarios. Furthermore, thanks to image eigen features affected by cascade image operations, it is possible to lead to a wrong white balance mode. Thus, we use the EXIF-white balance parameter as a manipulator indicator for forgery detection. Based on the forgery photos in practice, the proposed evidence can detect cascade manipulated images which are subject to copy-and-paste followed by different white balance post-processing operations, high compression or heavy downsampling.     

Indium tin oxide-free semi-transparent inverted polymer solar cells using conducting polymer as both bottom and top electrodes

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is investigated as a transparent cathode to replace indium tin oxide (ITO) in inverted polymer solar cells. Increasing the thickness of the PEDOT:PSS electrode leads to a reduction in transparency and sheet resistance which lowers the photocurrent but increases the fill factor of the solar cells. The offset of photocurrent and fill factor as the thickness is increased leads to a saturation of the power conversion efficiency to 3%. These electrodes were applied to flexible substrates showing similar device performance to glass based devices. Cyclic bending test of these flexible polymer electrodes show improved conversion efficiency retention (92%) when compared to flexible ITO based electrodes (50%) after 300 bend cycles. In addition to using PEDOT:PSS as a cathode replacement for ITO in inverted solar cells, its use as a semi-transparent anode replacement to Ag is also examined. Semi-transparent inverted solar cells fabricated with ITO as the cathode and PEDOT:PSS as the top anode electrode were demonstrated showing efficiencies of 2.51% while replacement of both ITO and Ag with PEDOT:PSS as both the cathode and anode show efficiencies of 0.47%.     

Metastable Copper‐Phthalocyanine Single‐Crystal Nanowires and Their Use in Fabricating High‐Performance Field‐Effect Transistors

This paper describes a simple, vapor‐phase route for the synthesis of metastable α‐phase copper‐phthalocyanine (CuPc) single‐crystal nanowires through control of the growth temperature. The influence of the growth temperature on the crystal structures, morphology, and size of the CuPc nanostructures is explored using X‐ray diffraction (XRD), optical absorption, and transmission electron microscopy (TEM). α‐CuPc nanowires are successfully incorporated as active semiconductors in field‐effect transistors (FETs). Single nanowire devices exhibit carrier mobilities and current on/off ratios as high as 0.4 cm² V^?1 s^?1 and >10⁴, respectively.     

A thyristor- and thermistor-based inrush current limiter for DC-link start-up

Large inrush currents can be harmful to equipment subjected to it and can also disturb other devices through voltage dips. Traditional ways of dealing with large inrush currents include the usage of parasitic elements in the supply, negative temperature coefficient (NTC) resistances and start-up relays. These solutions have several disadvantages among which are a non-negligible standby consumption, using a relay or a compromise between inrush current and load losses using an NTC. This paper proposes a solution which solves these disadvantages. The proposed circuit uses a semi-controlled bridge rectifier requiring a very low standby power consumption and is capable of withstanding grid interruptions. Moreover, it is designed to power on only when the load is not too heavy. This is accomplished by the use of positive temperature coefficient thermistors. The presented solution can be used for DC-link start-up circuits in applications with a power range from several watts up to a few kilowatts and it is particularly suitable for on-board battery chargers designed for electrical vehicles.     

Modelling of electrostatic gate operations in the Kane solid state quantum computer

The nuclear spin quantum computer proposed by Kane [Nature 393 (1998) 133] exploits as a qubit array ³¹P dopants embedded within a silicon matrix. Single-qubit operations are controlled by the application of electrostatic potentials via a set of metallic ‘A’ gates, situated above the donors, on the silicon surface, that tune the resonance frequency of individual nuclear spins, and a globally applied RF magnetic field that flips spins at resonance. Coupling between qubits is controlled by the application of potentials via a set of ‘J’ gates, between the donors, that induce an electron-mediated coupling between nuclear spins. We report the results of the study of the electric field and potential profiles arising within the Kane device from typical gate operations. The extent to which a single nuclear spin can be tuned independently of its neighbours, by operation of an associated A-gate, is examined and key design parameters in the Kane architecture are addressed. Implications for current fabrication strategies involving the implantation of ³¹P atoms are discussed. Solution of the Poisson equation has been carried out by simulation using a TCAD modelling package (Integrated Systems Engineering AG).     

Statistical Tolerance Analysis for Assured Analog Test Coverage

Increasing numbers of analog components in today's systems necessitate system level test composition methods that utilize on-chip capabilities rather than solely relying on costly DFT approaches. We outline a tolerance analysis methodology for test signal propagation to be utilized in hierarchical test generation for analog circuits. A detailed justification of this proposed novel tolerance analysis methodology is undertaken by comparing our results with detailed SPICE Monte-Carlo simulation data on several combinations of analog modules. The results of our experiments confirm the high accuracy and efficiency of the proposed tolerance analysis methodology.     

高性能高功率D类驱动器

D类音频放大器电路已经问世十余年，与一般的线性AB类拓朴相比，D类放大器不仅效率更高而且尺寸也更小。在一个AB类放大器上，经过其输出器件的电压等于扬声器和干线电压之间的电压差，并且会随音频信号的变化而变化。因此，功耗等于这个电压与输出电流的乘积。典型效率为30％。结果，AB类输出级通常需要具有散热器，如果允许，最好是一个风扇，特别是在功率水平超过50W的情况下更是如此。