Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Clinical evaluation of 0.5% ferric hyaluronate adhesion prevention gel for the reduction of adhesions following peritoneal cavity surgery: open-label pilot study

The objective of this study was to assess the safety and to make a preliminary assessment of the efficacy of 0.5% ferric hyaluronate adhesion prevention gel in reducing adhesions in patients undergoing peritoneal cavity surgery by laparotomy, with a planned 'second-look' laparoscopy. The study was a randomized, open-label, placebo-controlled, parallel-group design in patients desirous of fertility at the Women's and Children's Hospital, Department of Obstetrics and Gynecology, University of Southern California School of Medicine, Los Angeles, California. Female patients aged 24 to 41 years received 300 ml 0.5% ferric hyaluronate adhesion prevention gel or lactated Ringer's solution as an intraperitoneal instillate at the completion of the laparotomy procedure. At second-look laparoscopy 4-12 weeks after the laparotomy, the presence of adhesions was evaluated. Haematology and serum chemistry were determined throughout the study interval. All patients tolerated the procedures well and did not manifest any serious adverse events. At second-look laparoscopy, patients treated with 0.5% ferric hyaluronate adhesion prevention gel had significantly fewer adhesions than control patients. When adhesions did form, they were significantly less extensive and less severe in patients who received 0.5% ferric hyaluronate adhesion prevention gel. In conclusion, 0.5% ferric hyaluronate adhesion prevention gel was safe and highly efficacious in the reduction of the number, severity and extent of adhesions throughout the entire abdomen following peritoneal cavity surgery.     

Thermoelastic solutions for orthotropic and anisotropic composite laminates

Solutions, within the framework of linear uncoupled thermoelasticity, are presented for certain problems of flexure of composite laminates. Benchmark numerical results, useful for the validation or otherwise of approximate laminate models, are tabulated. Finally, these results are used to examine the accuracy of the classical lamination theory based on Kirchhoff's hypothesis.     

Fallibility of persistent blood return for confirmation of intravascular catheter placement in patients with hemorrhagic thoracic effusions

Two patients are described with hemorrhagic thoracic effusions who required central venous catheterization. Presumed subclavian and internal jugular vein cannulation, ipsilateral to the hemorrhagic thoracic effusions, was confirmed by the operators in each case by the persistent aspiration of blood. Subsequent clinical and radiologic evaluation revealed that the vascular catheters were introduced into the pleural space. In both individuals, the persistent aspiration of extravascular hemorrhagic fluid mimicked intravascular catheter positioning. Physicians treating patients with hemorrhagic thoracic effusions need to be aware of this potential complication that can result in the delayed resuscitation of hemodynamically unstable patients.     

Zooplankton population in the river tigris: Effects of samarra impoundment

The influences of the Samarra impoundment on the ecology of the downstream sector of the river Tigris are investigated. Zooplankton were collected monthly from July 1987 to July 1988. It was found that zooplankton were most abundant during high river discharges in March. During the month of low river discharge, September, the zooplankton population was greatly reduced immediately below the barrage and remained so to the last downstream station. Several factors seem to explain such differences. The high discharge from the impoundment was found to be the dominating factor and may flush the small backwaters in which zooplankton were abundant, thus increasing the population in the river. Zooplankton species vary in their ability to sustain populations in the river, variations which are due mainly to species-specific characteristics.     

Effects of molybdenum additions on the structure, depth, and austenite grain size of the case of carburized 0.13% carbon steels

Carbon (0.13%) steel samples containing about 0.48% molybdenum (Mo) singly and in combination with nickel (Ni) were carburized in a natural Titas gas atmosphere at a temperature of 1223 K (950 °C) and at a pressure of about 0.10 MPa (15 psia) for time periods ranging from 1–4 h followed by slow cooling in the furnace. Their microstructure was studied by optical microscopy. The austenite grain size of the case and the case depths were determined. It was found that Mo and Ni alone and in combination decrease the thickness of the cementite network near the surface of the carburized case of the steels. However, Ni is found to be more effective than Mo in decreasing the thickness of cementite network. Both Mo and Ni enhance the formation of Widmanstätten cementite plates at the grain boundary and within the grains near the surface of the carburized steels. However, Ni alone is more effective than Mo in the formation of Widmanstätten cementite plates. In the presence of Ni, Mo is much more effective in the formation of Widmanstätten cementite plates than Mo in absence of Ni. It was also revealed that both Mo and Ni increased the case depth. Ni is more effective than Mo in increasing the case depth. The combined effect of Mo and Ni is much greater than that of either Mo or Ni alone in increasing case depth. Mo as Mo carbide (Mo₂C) particles refined the austenite grain size of the carburized case. Ni in solution was not found to have any effect in restricting grain growth of austenite, but the presence of Ni enhances the austenite grain size refining effect of Mo in the carburized case.     

Capacity planning in job-shop environment

Presented here is a computerized capacity planning system for the IBM Microcomputer family. The system maintains the profile of the job shop in a data base along with data pertinent to various products that can be manufactured in the shop. Projected orders for the planning period are input to the system with their associated quantities and delivery dates. The system uses the forward and backward loading rules in generating capacity loading scenarios. User selects the best course of action which may satisfy delivery dates subject to the limitations of the work centers. Efficiency figures are provided to aid the user in his/her decision.     

Effect of thermal treatment on ZnO substrate for epitaxial growth

ZnO is a highly efficient photon emitter, and has optical and piezoelectric properties that are attractive for a variety of applications in sensors and potentially optoelectronic devices such as emitters. Due to its identical stacking order and close lattice match to GaN, it is also being developed as a substrate material for GaN epitaxy. However, the surface finish of the ZnO is such that much of the damage induced by sawing and follow up mechanical polishing remains. We developed a thermal treatment method to eliminate surface damage on the 0 face of ZnO (0 0 0 1) to prepare it for epitaxial growth. Atomic force microscopy images of ZnO (0 0 0 1) annealed at 1050 °C for 3 h etc. show that residual scratches from mechanical polishing are removed and atomically flat, terrace-like surfaces are attained. In addition, low-temperature photoluminescence and high-resolution X-ray diffraction measurements have been employed to investigate the effect of annealing on ZnO substrates.