The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

Windenergieausbau als Teil der Ökostromentwicklung

The new law for the support of electricity produced by renewable sources in Austria (Ökostromgesetz) which came into force with the beginning of 2003, shows its impacts already after the first months. Investments into wind power have increased considerably. These will be accompanied by activities for electricity production by biomass and biogas. The 4%-target quota will probably be reached earlier than the 2008 target period of the law.     

Schätzung der modalen Parameter unter Berücksichtigung systematischer Fehler der Frequenzgänge

Zusammenfassung Aufgrund von Eingangs- und Ausgangsst?rungen des Me?systems sowie einer endlichen Frequenzaufl?sung treten stets systematische (Bias-) und zuf?llige Fehler bei gemessenen Frequenzg?ngen und deren Varianzen auf. Auf solchen Frequenzg?ngen und Varianzen beruhende Sch?tzungen der modalen Parameter sind damit ebenfalls systematisch verzerrt. Um die Genauigkeit und Sicherheit der modalen Parameter zu erh?hen, wird ein Sch?tzverfahren vorgestellt, in dem der Einflu? der Biasfehler auf die Sch?tzung n?herungsweise in einer diagonalen Wichtungsmatrix berücksichtigt wird. Es wird gezeigt, da? die systematischen Fehler Einflu? auf die Absch?tzung der statistischen Sicherheit der modalen Parameter haben. Anhand zweier Beispiele wird die Wirksamkeit des Sch?tzverfahrens demonstriert. Prof. Dr.-Ing. Dr.-Ing. E.h.H.K. T?nshoff: Dipl.-Ing.Z. Liu, Institut für Fertigungstechnik und Spanende Werkzeugmaschinen (IFW), Universit?t Hannover.     

Selectivity in Methanol Oxidation as Studied on Model Systems Involving Vanadium Oxides

Oxidation catalysts are modeled by oxide single crystals, thin oxide films, as well as supported oxide nanoparticles. We characterize the surface of those materials using a variety of surface sensitive techniques including scanning tunneling microscopy and spectroscopy, photoelectron spectroscopy, infrared spectroscopy, and thermal desorption spectroscopy. We find temperature dependent structural transformations from V₂O₅(001) to V₂O₃(0001) via V₆O₁₃(001). V₂O₃(0001) is found to be vanadyl terminated in an oxygen ambient and it loses the vanadyl termination after electron bombardment. It is shown that the concentration of vanadyl groups controls the selectivity of the methanol oxy-dehydrogenation towards formaldehyde. A proposal for the mechanism is made. The results on single crystalline thin films are compared with similar measurements on deposited vanadia nanoparticles. The experimental results are correlated with theoretical calculations and models.     

Dissolution kinetics of ulexite in acetic acid solutions

Ulexite is an important boron mineral used for the production of boron compounds. The aims of this study are to examine the dissolution kinetics of ulexite in acetic acid solutions, and to present an alternative process to produce boric acid. In order to investigate the dissolution kinetics of ulexite in acetic acid solutions, the concentration of solution, reaction temperature, solid-to-liquid ratio, and particle size were selected as experimental parameters. It was determined that the dissolution rate of ulexite increased with increasing solution concentration and temperature and decreasing particle size and solid-to-liquid ratio. The activation energy of the process was found to be 55.8 kJ/mol.     

Preparation of Phase-Pure M1 MoVTeNb Oxide Catalysts by Hydrothermal Synthesis—Influence of Reaction Parameters on Structure and Morphology

This work presents a detailed investigation of the preparation of MoVTeNbO _x catalysts by hydrothermal synthesis. Phase-pure synthesis of M1 has been achieved applying the metals in a molar ratio Mo/V/Te/Nb = 1/0.25/0.23/0.12. Raman, UV/Vis spectroscopy, and SEM/EDX analysis show that the elements are inhomogeneously distributed in the initial suspension that is formed after mixing the metal salts in an aqueous medium. Iso- and heteropoly anions of molybdenum, free telluric acid as well as supra-molecular polyoxometalate clusters are observed in the solution, whereas all metals have been found in the precipitate. Complete rearrangement of molecular building blocks under hydrothermal conditions is essential for formation of phase-pure materials. Optimized synthesis conditions with respect to temperature and time result in the formation of a precursor consisting of nano-structured M1 characterized by an extended periodic organization in the [001] direction and a fairly homogeneous distribution of the elements. Residual ammonium containing supra-molecular species in the precursor result in the formation of phase mixtures during the subsequent crystallization by heat treatment in inert gas. Phase-pure M1 exhibits a distinct degree of flexibility with respect to the chemical composition that becomes obvious by incorporating Nb not exclusively into pentagonal bi-pyramidal units, but also into octahedral coordinated positions as shown by EXAFS. Anisotropic growth of the needle-like M1 crystals has been observed during the final heat treatment performed at 873–923 K in inert atmosphere disclosing a potential method to control the catalytic properties of MoVTeNbO _x catalysts.