Influence of initial growth layer and Ti underlayer on magneticproperties and recording characteristics of very thin films ofevaporated Co-Cr media

A Co-Cr film deposited directly on a substrate has an initial growth layer with low coercivity. However, the existence of a Ti underlayer prevents the formation of such a layer. As a result, Co-Cr film deposited on a Ti underlayer has high perpendicular anisotropy and coercivity even in cases of extremely thin film thickness (200 Å). As for the read-write characteristics of Co-Cr thin-film media, the existence of such an initial growth layer greatly improves the reproduced output level. The cause for this is considered to be that the free charges which appear on the back surface of the perpendicular recording layer are reduced and the demagnetization field acting on the recorded magnetization subsequently decreases due to the existence of the initial growth layer     

Near-resonance oscillations of a nonsymmetric nonlinear system with a crack

The Malkin method, which was developed to construct a single unique resonance solution of nonlinear equations, is generalized for the case of the derivation of all stationary solutions in the near-resonance zone, and also for transient oscillations.Kiev Polytechnic Institute. Translated from Problemy Prochnosti, No. 10, pp. 108–112, October, 1989.     

The solution of the inverse problem of gravitational potential using a set of measurements of different field elements

A numerical solution of the inverse problem of the gravitational field at a single point is obtained using six field elements for a point, a spherical cap, a differential spherical sector and a vertical segment. In the system of six equations obtained, the unknowns are the mass of the body, the depth of its center, and the second, third, and fourth degree moments. The accuracy of the solution of this system is ten times higher than when using three field elements. __________ Translated from Izmeritel’naya Tekhnika, No. 5, pp. 3–8, May, 2007.     

Fine Purification of Monoisotopic Silanes 28SiH4 , 29SiH4 , and 30SiH4 via Distillation

High-purity isotopically enriched (99.98% ²⁸Si, 99.57% ²⁹Si, and 99.83% ³⁰Si) silane samples are prepared for the first time. The total hydrocarbon content of the samples is no higher than 0.1–0.3 ppm. The concentration of electroactive impurities in the silicon prepared from the purified monoisotopic silane is below 10¹⁵ cm^–3.     

On the role of high-energy electrons in the formation of a plasma-beam discharge structure in a diode with a slit cathode

The spatial structure of visible emission from plasma of a transverse nanosecond pulsed electric discharge in a gas-filled diode with a hollow (slit) cathode has been experimentally studied. A relation is established between the regime of electron energy relaxation and the plasma-beam discharge structure formation. High values of the electron emission coefficient are observed in the experiment, which cannot be explained using the notion of electron emission from a cathode bombarded by fast heavy particles.     

Optical properties of strain-compensated InAs/InGaAsN/GaAsN superlattices

The optical properties of heterostructures comprising InAs/InGaAsN quantum wells in strain-compensated GaAsN/InGaAsN superlattices have been studied. It is demonstrated that, using such superlattices of various design and thickness and with additional InAs monolayer spacers, it is possible to control the wavelength of room-temperature emission from InGaAsN quantum wells within 1.3–1.6 μm without deteriorating the output radiation characteristics, which opens additional prospects for the development of lasers on GaAs substrates for telecommunication applications.     

Effect of calcination conditions on phase formation and particle size of nickel niobate powders synthesized by solid-state reaction

The solid-state mixed oxide method via a rapid vibro-milling technique is explored in the preparation of single-phase nickel niobate (NiNb₂O₆) powders. The formation of the NiNb₂O₆ phase in the calcined powders has been investigated as a function of calcination conditions by TG-DTA and XRD techniques. Morphology, particle size and chemical composition have been determined via a combination of SEM and EDX techniques. It has been found that the minor phases of unreacted NiO and Nb₂O₅ precursors and the Ni₄Nb₂O₉ phase tend to form together with the columbite NiNb₂O₆ phase, depending on calcination conditions. More importantly, it is seen that optimization of calcination conditions can lead to a single-phase NiNb₂O₆ in an orthorhombic phase.     

Micro- and nanofabrication processes for hybrid synthetic and biological system fabrication

The application of micro- and nanofabrication processes to the development of hybrid synthetic and biological systems may enable the production of new devices such as controllable transporters, gears, levers, micropumps, or microgenerators powered by biological molecular motors. However, engineering these hybrid devices requires fabrication processes that are compatible with biological materials such as kinesin motor proteins and microtubules. In this paper, the effects of micro- and nanofabrication processing chemicals and resists on the functionality of casein, kinesin, and microtubule proteins are systematically examined to address the important missing link of the biocompatibility of micro- and nanofabrication processes needed to realize hybrid system fabrication. It is found that both casein, which is used to prevent motor denaturation on surfaces, and kinesin motors are surprisingly tolerant of most of the processing chemicals examined. Microtubules, however, are much more sensitive. Exposure to the processing chemicals leads to depolymerization, which is partially attributed to the pH of the solutions examined. When the chemicals were diluted in aqueous buffers, a subset of them no longer depolymerized microtubules and in their diluted forms still worked as resist removers. This approach broadens the application of micro- and nanofabrication processes to hybrid synthetic and biological system fabrication.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.