Comparison of trihalomethanes in tap water and blood

Trihalomethane (THM) concentrations in blood and tap water were measured for 50 women living in two locations with different bromide concentrations and disinfectant types. Blood samples were taken from each woman early in the morning prior to any major water-use activity and again immediately after showering. Each residence was sampled for THMs in tap water prior to the woman's shower. Cobb County, GA, tap water exhibited high THM concentrations composed primarily of chloroform. Corpus Christi, TX, tap water exhibited lower THM concentrations with significant proportions of brominated THMs. THMs in tap water and blood were compared using mole fraction speciation, extent of bromine incorporation, and correlation analysis. Results indicated that THMs in the blood rose significantly as a result of showering, that showering shifted the THM distribution in the blood toward that found in the corresponding tap water, and that THMs measured in the blood of women living in the two locations reflected species and concentration differences in their respective tap waters. In general, blood concentrations were not significantly correlated with tap water concentrations. This finding suggests that other factors, in addition to tap water concentrations, may be important in determining THM concentrations in the blood.     

Life-cycle assessment of hydrogen technologies with the focus on EU critical raw materials and end-of-life strategies

We present the results of a life-cycle assessment (LCA) for the manufacturing and end-of-life (EoL) phases of the following fuel-cell and hydrogen (FCH) technologies: alkaline water electrolyser (AWE), polymer-electrolyte-membrane water electrolyser (PEMWE), high-temperature (HT) and low-temperature (LT) polymer-electrolyte-membrane fuel cells (PEMFCs), together with the balance-of-plant components. New life-cycle inventories (LCIs), i.e., material inputs for the AWE, PEMWE and HT PEMFC are developed, whereas the existing LCI for the LT PEMFC is adopted from a previous EU-funded project. The LCA models for all four FCH technologies are created by modelling the manufacturing phase, followed by defining the EoL strategies and processes used and finally by assessing the effects of the EoL approach using environmental indicators. The effects are analysed with a stepwise approach, where the CML2001 assessment method is used to evaluate the environmental impacts. The results show that the environmental impacts of the manufacturing phase can be substantially reduced by using the proposed EoL strategies (i.e., recycled materials being used in the manufacturing phase and replacing some of the virgin materials). To point out the importance of critical materials (in this case, the platinum-group metals or PGMs) and their recycling strategies, further analyses were made. By comparing the EoL phase with and without the recycling of PGMs, an increase in the environmental impacts is observed, which is much greater in the case of both fuel-cell systems, because they contain a larger quantity of PGMs.     

High resolution spatiotemporal patterns of flow at the landscape scale in montane non-perennial streams

Intermittent and ephemeral streams in dryland environments support diverse assemblages of aquatic and terrestrial life. Understanding when and where water flows provide insights into the availability of water, its response to external controlling factors, and potential sensitivity to climate change and a host of human activities. Knowledge regarding the timing of drying/wetting cycles can also be useful to map critical habitats for species and ecosystems that rely on these temporary water sources. However, identifying the locations and monitoring the timing of streamflow and channel sediment moisture remains a challenging endeavor. In this paper, we analyzed daily conductivity from 37 sensors distributed along 10 streams across an arid mountain front in Arizona (United States) to assess spatiotemporal patterns in flow permanence, defined as the timing and extent of water in streams. Conductivity sensors provide information on surface flow and sediment moisture, supporting a stream classification based on seasonal flow dynamics. Our results provide insight into flow responses to seasonal rainfall, highlighting stream reaches very reactive to rainfall versus those demonstrating more stable streamflow. The strength of stream responses to precipitation are explored in the context of surficial geology. In summary, conductivity data can be used to map potential stream habitat for water-dependent species in both space and time, while also providing the basis upon which sensitivity to ongoing climate change can be evaluated.     

Experimentelle und numerische Untersuchungen zum Tragverhalten von Stahlbetondecken mit kugelförmigen Hohlkörpern

Massive Flachdecken erweisen sich in Hoch‐ und Industriebau häufig als insgesamt überlegenes Deckensystem. Die hohe Eigenlast dieser Decken kann ihren Anwendungsbereich jedoch einschränken. Eine sinnvolle Abhilfe schafft dann die Integration von Hohlkörpern in der neutralen Zone, weil hierdurch eine spürbare Gewichtsreduktion eintritt. Neben der Eigenlast wird auch der Verbrauch der unter ökologischen Gesichtspunkten wesentlichen Ressourcen Betonstahl und Zement deutlich verringert. Die Hohlräume beeinflussen vor allem die Querkrafttragfähigkeit solcher Decken. Vier Versuchsserien, die mit kugelförmigen Hohlkörperdecken des Systems “cobiax” durchgeführt wurden, werden in diesem Beitrag beschrieben. Aus den Versuchen wird ein Abminderungsfaktor zur Beschreibung des Querkrafttragverhaltens abgeleitet, der auch in die kürzlich erteilte allgemeine bauaufsichtliche Zulassung des Deckensystems eingegangen ist. Die Nachrechnung der Versuche mit der Finite‐Elemente‐Methode zeigt eine gute Übereinstimmung von Numerik und Experiment, so dass in der Weiterentwicklung Parameterstudien auf dieser Grundlage zur Ergänzung von Versuchen hilfreich sein werden. Experimental and Numerical Investigation of the Bearing Behaviour of Hollow Core Slabs Massive flat slabs have proven to be the most appropriate ceiling system for structural and industrial engineering. However the high dead load of these slabs might reduce their field of application. This problem can be solved by void formers that are placed in the neutral zone. These block‐outs cause a noticeable reduction of weight. Furthermore, the masses of ecologically important resources like reinforcement steel and cement can be reduced as well. The shear bearing capacity is significantly influenced by these block‐outs. This article describes four test series with spherical void former floors of the system “cobiax”. A reduction factor for the shear bearing capacity is derived from these tests. That factor was also introduced in the technical approval for this slab system which has been issued recently. A comparison to a calculation with the finite element method shows that the numerical results and the results of the tests are quite similar. In future research, parameter studies based on the finite element method might be helpful additional to further tests.     

Effect of titanium implantation on the friction and surface chemistry of a Co-Cr-W-C alloy

The effects of the implantation of titanium ions, to a fluence of 5 × 10¹⁷ Ti ions cm^-2 at 190 keV, on the tribological behavior of a centrifugally cast cobalt-based alloy (Stoody 3) were investigated by friction tests against a variety of alloy and carbon counterfaces. Dry sliding friction coefficients were compared with those made on similarly prepared, but non-implanted, and fatty-acid-coated samples. High friction coefficients (μ_K ≈ 0.6) for the alloy-Stoody 3 couples coincided with the formation of debris, with the same composition as the softer of the mating alloys, in the wear scars. Much lower μ_K values were measured on titanium-implanted (μ_K ≈ 0.25) and acid-coated (μ_K ≈ 0.1) surfaces. Optical microscopy indicated a change in the surface texture of the implanted surfaces attributable to sputtering. Auger spectroscopy showed that vacuum carburization of both carbide and matrix phases of the Stoody alloy occurred during implantation. The friction and wear mechanisms involved are discussed.     

A pilot-scale evaluation of magnetic ion exchange treatment for removal of natural organic material and inorganic anions

The objective of this research was to evaluate a magnetic ion exchange process (MIEX) for the removal of natural organic material (NOM) and bromide on a continuous-flow pilot-scale basis under different operating conditions and raw water characteristics. The most important operating variable was the effective resin dose (ERD), which is the product of the steady-state resin concentration in the contactor and the regeneration ratio. The raw water employed in this study had a moderate concentration of ultraviolet (UV)-absorbing substances and dissolved organic carbon (DOC), and a low turbidity, alkalinity, and concentration of competing anionic species. Experiments were conducted using the ambient raw water and raw water spiked with bromide, chloride, and sulfate. Substantial removal of UV-absorbing substances and DOC was achieved at ERDs as low as 0.16mL/L. Moderate bromide removal was achieved, depending on the ERD. Increasing the sulfate concentration resulted in decreased removal of UV-absorbing substances, DOC, and bromide. Consistent results were observed between the continuous-flow pilot plant tests and batch equilibrium studies.     

Performance of a CO2 sorbent for indoor air cleaning applications: Effects of environmental conditions,sorbent aging,and adsorption of co-occurring formaldehyde

Indoor air cleaning systems that incorporate CO₂ sorbent materials enable HVAC load shifting and efficiency improvements. This study developed a bench-scale experimental system to evaluate the performance of a sorbent under controlled operation conditions. A thermostatic holder containing 3.15 g sorbent was connected to a manifold that delivered CO₂-enriched air at a known temperature and relative humidity (RH). The air stream was also enriched with 0.8-2.1 ppm formaldehyde. The CO₂ concentration was monitored in real-time upstream and downstream of the sorbent, and integrated formaldehyde samples were collected at different times using DNPH-coated silica cartridges. Sorbent regeneration was carried out by circulating clean air in countercurrent. Almost 200 loading/regeneration cycles were performed in the span of 17 months, from which 104 were carried out at reference test conditions defined by loading with air at 25°C, 38% RH, and 1000 ppm CO₂, and regenerating with air at 80°C, 3% RH and 400 ppm CO₂. The working capacity decreased slightly from 43-44 mg CO₂ per g sorbent to 39-40 mg per g over the 17 months. The capacity increased with lower loading temperature (in the range 15-35°C) and higher regeneration temperature, between 40 and 80°C. The CO₂ capacity was not sensitive to the moisture content in the range 6-9 g/m³, and decreased slightly when dry air was used. Loading isothermal breakthrough curves were fitted to three simple adsorption models, verifying that pseudo-first-order kinetics appropriately describes the adsorption process. The model predicted that equilibrium capacities decreased with increasing temperature from 15 to 35°C, while adsorption rate constants slightly increased. The formaldehyde adsorption efficiency was 80%-99% in different cycles, corresponding to an average capacity of 86 ± 36 µg/g. Formaldehyde was not quantitatively released during regeneration, but its accumulation on the sorbent did not affect CO₂ adsorption.     

Impact of a magnetic ion exchange resin on ozone demand and bromate formation during drinking water treatment

The objective of this research was to examine the impact of a magnetic ion exchange resin (MIEX) on ozone demand and bromate formation in two different ozonated waters at bench scale. The first raw water had a high bromide ion concentration, a high ozone demand, and was highly colored. Based on experimental findings from the first water, the second water was selected as a model water in which more controlled experiments were performed. The waters were treated with the MIEX resin using jar test procedures to find the optimal MIEX dosage based upon the removal of ultraviolet (UV)-absorbing substances, dissolved organic carbon (DOC), and bromide. The optimal resin dosage was chosen for bulk MIEX treatment and subsequent ozonation in a semi-batch reactor. The ozone demand and formation of bromate were analyzed as a function of ozone dosage and dissolved ozone concentration for the MIEX pre-treated water, and compared to the results obtained by ozonating the water without MIEX pre-treatment. The results indicate that pre-treatment of the water with the MIEX resin significantly reduces total organic carbon, DOC, UV absorbance, color, and to some extent, bromide. MIEX pre-treatment of the water prior to ozonation substantially lowered the ozone demand and formation of bromate during subsequent ozonation.