Removal of N‐butanol from aqueous solutions by ion–exchange membranes containing organic counterions

The pervaporation of aqueous butanol solutions was investigated using thin‐film composite membranes composed of a poly(vinylidene fluoride) substrate coated with a sulfonated poly(2,6‐dimethyl‐1,4‐phenelene oxide) polymer. The polymer was ion‐exchanged with quaternary ammonium cations having aliphatic substituents of various chain lengths. The pervaporation of aqueous n‐butanol solutions using these membranes gave a permeate more concentrated in n‐butanol; therefore, they were alcohol‐selective. The separation factor increased and the permeate flux decreased as the chain lengths of the aliphatic substituents were increased. Hence, the mass‐transport properties of such membranes can be controlled or altered to yield some desired permselectivity by the introduction of a proper counterion. It was observed that the n‐butanol flux was small relative to the total flux and, therefore, the water flux dominated the total permeate flux. The degree of swelling of the membranes and its effect on membrane performance was investigated as well. As the n‐butanol content was increased, the swelling of the membranes increased greatly. High membrane swelling caused a reduction in the separation factor. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 47–58, 1999     

Investing in recovering water for the environment in Australia's Murray-Darling Basin

Irrigated agriculture makes an important contribution to the economy of Australia's Murray-Darling Basin. Competing water demand, recurring drought and climate change have ushered in an era of water policy reform. To recover water for the environment, surface water extraction is capped and investment in irrigation infrastructure is prioritized. This article applies a computable general equilibrium model to evaluate the economic impacts of investment in irrigation in a case study of the Murrumbidgee subcatchment. Results indicate an increase in regional output, income and employment, while at the national level there is a small negative impact resulting from the transfer of resources to the basin and the crowding out of private investment.     

Effect of Natural and Synthetic Surfactant on the Rheology of Light Crude Oil

Comparative effectiveness of natural surfactant extracted from Sapindus mukorossi in laboratory and commercial surfactant Brij 30 was determined. Light crude oil was collected from ONGC, Gujarat, India. Its pour point and viscosity decreased significantly after adding surfactants. Wax crystal structure and crystal size distribution was analyzed using cross polarized light microscope and dynamic light scattering techniques. There was remarkable reduction in radius of wax crystals after addition of both the surfactants. Microscopic studies showed significant change in size and structure of wax crystals favoring reduction in viscosity. The possible mechanism behind improvement of flow properties was also analyzed through FTIR studies.     

A MATHEMATICAL MODEL FOR MILD HYDROCRACKING:KINETICS AND PRODUCT YIELDS FROM A CRUDE OIL BLEND IN LIGHT GAS OIL OVER HYDROTREATING CATALYST.

Abstract

Mild hydrocracking of 30% crude oil (Indian Crude oil.North Gujarat base)solution in light gas oil is carried out over a commercial hydrotreating catalyst at a temperature range of 300–450°c and pressure of 6. 8–20.OMpa in laboratory reactor. About 30 to 60% of the long residue (365° c+ cut) in the solution is converted to light distillates.

A mathematical model has been developed to predict the yields of products.     

Assessment of an active-cooling micro-channel heat sink device,using electro-osmotic flow

Non-uniform heat flux generated by microchips causes “hot spots” in very small areas on the microchip surface. These hot spots are generated by the logic blocks in the microchip bay; however, memory blocks generate lower heat flux on contrast. The goal of this research is to design, fabricate, and test an active cooling micro-channel heat sink device that can operate under atmospheric pressure while achieving high-heat dissipation rate with a reduced chip-backside volume, particularly for spot cooling applications. An experimental setup was assembled and electro-osmotic flow (EOF) was used thus eliminating high pressure pumping system. A flow rate of 82 μL/min was achieved at 400 V of applied EOF voltage. An increase in the cooling fluid (buffer) temperature of 9.6 °C, 29.9 °C, 54.3 °C, and 80.1 °C was achieved for 0.4 W, 1.2 W, 2.1 W, and 4 W of heating powers, respectively. The substrate temperature at the middle of the microchannel was below 80.5 °C for all input power values. The maximum increase in the cooling fluid temperature due to the joule heating was 4.5 °C for 400 V of applied EOF voltage. Numerical calculations of temperatures and flow were conducted and the results were compared to experimental data. Nusselt number (Nu) for the 4 W case reached a maximum of 5.48 at the channel entrance and decreased to reach 4.56 for the rest of the channel. Nu number for EOF was about 10% higher when compared to the pressure driven flow. It was found that using a shorter channel length and an EOF voltage in the range of 400–600 V allows application of a heat flux in the order of 10⁴ W/m², applicable to spot cooling. For elevated voltages, the velocity due to EOF increased, leading to an increase in total heat transfer for a fixed duration of time; however, the joule heating also got elevated with increase in voltage.     

A Numerical Study of Combined Heat and Mass Transfer in an Inclined Channel Using the VOF Multiphase Model

A numerical study has been performed to determine heat and mass transfer from the surface of liquid ethanol flowing in an inclined channel. The Volume-of-fluid (VOF) multiphase model was used to track the liquid and gas phases. An algorithm has been implemented to determine interfacial heat and mass transfer characteristics. A parametric study was done to determine the effect of gas-phase inlet velocity, temperature, and vapor mass fraction.     

Correction to: Performance Analysis of Cooperative Spectrum Sensing Network Using Optimization Technique in Different Fading Channels

Wireless Personal Communications - In order to reduce the cost of logistics distribution, a capacitated open vehicle routing problem with split deliveries by order is studied. According to the...     

An efficient BEM formulation for three-dimensional steady-state heat conduction analysis of composites

In this work, an efficient boundary element formulation has been presented for three-dimensional steady-state heat conduction analysis of fiber reinforced composites. The cylindrical shaped fibers in the three-dimensional composite matrix are represented by a system of curvilinear line elements with a prescribed diameter which facilitates efficient analysis and modeling together with the reduction in dimensionality of the problem. The variations in the temperature and flux fields in the circumferential direction of the fiber are represented in terms of a trigonometric shape function together with a linear or quadratic variation in the longitudinal direction. The resulting integrals are then treated semi-analytically which reduces the computational task significantly. The computational effort is further minimized by analytically substituting the fiber equations into the boundary integral equation of the material matrix with hole, resulting in a modified boundary integral equation of the composite matrix. An efficient assembly process of the resulting system equations is demonstrated together with several numerical examples to validate the proposed formulation. An example of application is also included.     

Improved genetic algorithm for channel allocation with channel borrowing in mobile computing

This paper exploits the potential of the Genetic Algorithm to solve the cellular resource allocation problem. When a blocked host is to be allocated to a borrowable channel, a crucial decision is which neighboring cell to choose to borrow a channel. It is an optimization problem and the genetic algorithm is efficiently applied to handle this. The Genetic Algorithm, for this particular problem, is improved by introducing a new genetic operator, named pluck, that incorporates a problem-specific knowledge in population generation and leads to a better channel utilization by reducing the average blocked hosts. The pluck operator makes the crucial decision of when and which cell to borrow with the future consideration that the borrowing should not lead the network to chaos. It makes a channel borrowing decision that minimizes the number of blocked hosts and improves the long-term performance of the network. Efficacy of the proposed method has been evaluated by experimentation.     

Synthesis of nanocrystalline hydroxyapatite using surfactant template systems: Role of templates in controlling morphology

Hydroxyapatite (HA) nanopowder was synthesized by reverse microemulsion technique using calcium nitrate and phosphoric acid as starting materials in aqueous phase. Cyclohexane, hexane, and isooctane were used as organic solvents, and Dioctyl sulfosuccinate sodium salt (AOT), dodecyl phosphate (DP), NP5 (poly(oxyethylene)₅ nonylphenol ether), and NP12 (poly(oxyethylene)₁₂ nonylphenol ether) as surfactants to make the emulsion. Effect of synthesis parameters, such as type of surfactant, aqueous to organic ratio (A/O), pH and temperature on powder characteristics were studied. It was found that the surfactant templates played a significant role in regulating the morphology of the nanoparticle. Hydroxyapatite nanoparticle of different morphologies such as spherical, needle shape or rod-like were obtained by adjusting the conditions of the emulsion system. Synthesized powder was characterized using X-ray diffraction (XRD), BET surface area and transmission electron microscopy (TEM). Phase pure HA nanopowder with highest surface area of 121 m²/g were prepared by this technique using NP5 as a surfactant. Densification studies showed that this nanoparticle can give about 98% of their theoretical density. In vitro bioactivity of the dense HA compacts was confirmed by excellent apatite layer formation after 21 days in SBF solution. Cell material interaction study showed good cell attachment and after 5 days cells were proliferated on HA compacts in OPC1 cell culture medium. The results imply this to be a versatile approach for making hydroxyapatite nanocrystals with controlled morphology and excellent biocompatibility.