Synthesis of Ion Imprinted Polymers by Copolymerization of Zn(II) and Al(III)8-hydroxy Quinolone Complexes with Divinylbenzene and Methacryclic Acid

In this research work, Zinc(II) and Aluminum(III)-IIP's were synthesized by optimizing the amount of methacrylic acid as monomer, divinylbenzene as cross-linker. The IIP's were functionalized with 8-hydroxy quinolone complexes of the two metal ions under thermal conditions by copolymerization with monomer and cross-linker. The IIP's and Non-IIP's were characterized using FT-IR, TGA, and SEM analysis. A quite remarkable difference in the size was observed of the polymers (Zn(II) 1.0 µm and Al(III) 0.1 µm). A stronger affinity was observed with IIP in comparison with Non-IIP at pH 3.1 and 4.5 for Zn(II) and Al(III) ions on their respective polymers.     

Processing and properties of tape-cast alumina/zirconia laminates composites

In the present work, laminar ceramic structures formed by layers of alumina and partially stabilized zirconia were fabricated by water-based tape casting. Rheological, physical and mechanical properties of slurries and laminates were evaluated. The laminates consisted of stacked alumina and zirconia green tapes produced by thermopressing. Pyrolysis was carried out at 450 °C and sintering at 1500 °C. The alumina/zirconia laminates were studied for a better understanding of the formation behavior and crack propagation at the laminate interface. The flexural strength values of laminates depend on the stress state on their surface. The laminates with the highest amount of zirconia layers presented low strength values (6.7 MPa), while the laminates with more alumina layers had a higher strength level (57.7 MPa). This is because these laminates have alumina layers on the surface which are in a state of residual compressive stress.     

Identification of Phenylpyrazolone Dimers as a New Class of Anti-Trypanosoma cruzi Agents

Chagas disease is becoming a worldwide problem; it is currently estimated that over six million people are infected. The two drugs in current use, benznidazole and nifurtimox, require long treatment regimens, show limited efficacy in the chronic phase of infection, and are known to cause adverse effects. Phenotypic screening of an in-house library led to the identification of 2,2′-methylenebis(5-(4-bromophenyl)-4,4-dimethyl-2,4-dihydro-3H-pyrazol-3-one), a phenyldihydropyrazolone dimer, which shows an in vitro pIC₅₀ value of 5.4 against Trypanosoma cruzi. Initial optimization was done by varying substituents of the phenyl ring, after which attempts were made to replace the phenyl ring. Finally, the linker between the dimer units was varied, ultimately leading to 2,2′-methylenebis(5-(3-bromo-4-methoxyphenyl)-4,4-dimethyl-2,4-dihydro-3H-pyrazol-3-one (NPD-0228) as the most potent analogue. NPD-0228 has an in vitro pIC₅₀ value of 6.4 against intracellular amastigotes of T. cruzi and no apparent toxicity against the human MRC-5 cell line and murine cardiac cells.     

Effect of combining ethylene/methyl acrylate/glycidyl methacrylate terpolymer and an organoclay on the toughening of poly(lactic acid)

Blends of poly(lactic acid) (PLA) and ethylene/methyl acrylate/glycidyl methacrylate terpolymer (EMA‐GMA) with and without the addition of an organoclay were prepared by melt mixing in a twin screw extruder. Mechanical, morphological, structural, and rheological properties of the systems have been investigated as function of its compositions. The impact strength (IS) of PLA increased with the addition of EMA‐GMA. Furthermore, the addition of 2.5 wt% of organoclay to the PLA/EMA‐GMA blend promoted improvements in the mechanical properties, such as IS, tensile strength, and strain‐at‐break. Further addition of organoclay, 5 wt%, led to a formation of a double percolated network, where the clay particles form bridges across EMA‐GMA droplets and glue them together, however, without coalescence. In addition, morphological and wide‐angle X‐ray scattering analyses evidenced that the clay presents a partially exfoliated structure and that remains inside the EMA‐GMA droplets, probably as a consequence of the approach used to produce the systems. POLYM. ENG. SCI., 54:1922–1930, 2014. © 2013 Society of Plastics Engineers     

Web-GIS models: accomplishing modularity with aspects

Spatial concerns of Web geographical information systems (Web-GIS) are inherently crosscutting and volatile: crosscutting because they affect multiple functionalities of Web-GIS systems, and volatile because their status may change often. If these concerns are not modularized properly, the quality of Web-GIS services, particularly with regard to adaptation and evolution, can be severely compromised. This paper uses aspect-orientation to model crosscutting and volatile spatial concerns. By modeling both types of concerns, crosscutting and volatile, as candidate aspects, one can use dynamic weaving to add or remove them from a system at runtime. The aspect-oriented approach proposed starts with the identification and specification of crosscutting concerns and follows by composing these using modeling aspects using a transformation approach, an aspect-oriented modeling technique. The conflicts that can emerge due to the composition order are also taken into consideration. Finally, this paper proposes a set of reusable GIS crosscutting concerns, documenting them in a concern catalogue.     

A Stochastic Neural Model for Fast Identification of Spatiotemporal Sequences

In this Letter, a new approach to build a neural model for the fast identification of spatiotemporal sequences is proposed. Such a model, the Stochastic Neural Sequence Identifier (SNSI), is simple and rapidly learns and identifies a given sequence. The SNSI receives as input several patterns belonging to a particular spatiotemporal sequence and produces as output a label for the sequence identified and a probability of this classification being correct. The SNSI is able to identify a sequence from patterns learned during training or novel ones, i.e., combinations of the sequence items distinct from those belonging to the trained set. The SNSI was tested on a 2D set of both closed and open trajectories with varying levels of complexity. The results suggest that the SNSI is able to recognize all the patterns presented in the training and most of the novel patterns used for testing.     

Blockchain and smart contract architecture for notaries services under civil law: a Brazilian experience

International Journal of Information Security - This paper proposes a blockchain solution for some activities currently performed by notary offices under the Civil Law judiciary that is technically...     

Strategic Assessment of Lisbon’s Accessibility and Mobility Problems from an Equity Perspective

Accessibility planning with reference to sustainability and equity principles has been advocated as the best approach to deal with the urban mobility complexity. It has enabled the development of more sustainable and fair policies in relation to access provision. However, despite this paradigm shift, many planning initiatives in practice are still focused on assessing alternatives and proposing solutions, instead of centering on the understanding and assessment of problems as the primary activity of planning. Therefore, in order to contribute for the problem-oriented paradigm in the accessibility planning, this work proposes a strategic assessment methodology for unequal and inequitable distribution problems of accessibility and mobility. This methodology relies on spatial analysis techniques and allows the characterization of accessibility and mobility conditions, as well as the diagnosis of accessibility and mobility problems and their causal relationships. It was applied for the case of Lisbon and the results of the performed assessment allowed an intelligent reading of the problems considered. Specifically, it was found that Lisbon presents an unequal and inequitable distribution of job accessibility and mobility by private car and public transport, and also that job accessibility, along with other transportation, land-use and socioeconomic variables, impact the mobility levels of its citizens.     

An haptic-based immersive environment for shape analysis and modelling

Currently, the design of aesthetic products is a process that requires a set of activities where digital models and physical mockups play a key role. Typically, these are modified (and built) several times before reaching the desired design, increasing the development time and, consequently, the final product cost. In this paper, we present an innovative design environment for computer-aided design (CAD) surface analysis. Our system relies on a direct visuo-haptic display system, which enables users to visualize models using a stereoscopic view, and allows the evaluation of sectional curves using touch. Profile curves are rendered using an haptic device that deforms a plastic strip, thanks to a set of actuators, to reproduce the curvature of the shape co-located with the virtual model. By touching the strip, users are able to evaluate shape characteristics, such as curvature or discontinuities (rendered using sound), and to assess the surface quality. We believe that future computer-aided systems (CAS)/CAD systems based on our approach will contribute in improving the design process at industrial level. Moreover, these will allow companies to reduce the product development time by reducing the number of physical mockups necessary for the product design evaluation and by increasing the quality of the final product, allowing a wider exploration and comparative evaluation of alternatives in the given time.