Fracture toughness of bisphenol A‐type epoxy resin

The relationship between the postcuring conditions and the fracture toughness of a bisphenol A‐type epoxy resin cured with acid anhydride was investigated. The glass transition temperature and fragility parameter, derived from the thermo‐viscoelasticity, were used to characterize the epoxy resin postcured under various conditions. Relationship between these two parameters and the fracture toughness was then investigated, based on the fractography results of a microscopic roughness examination of a fractured surface. The values of the glass transition temperature and fragility greatly depended on the postcuring conditions. The glass transition temperature was approximately 400 K when the crosslinking reaction was saturated. The fragility was independent of the saturation of the reaction and varied between 50 and 180. The results of the fracture test and fractography examination showed that there was no direct correlation between the glass transition temperature, the fracture toughness, and the roughness. On the other hand, there was a correlation between the fragility, fracture toughness, and roughness when the glass transition temperature saturated (at 400 K). As the fragility decreased from 180 to 50, the fracture toughness increased from 0.6 to 1.1 MPa · m^1/2 at the same glass transition temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 10: 2266–2271, 2002     

Reverse osmosis separation of phenols in aqueous solutions using porous cellulose acetate membranes

Reverse osmosis separations of phenol (9.4 to 108 ppm), p-cresol (108 ppm), and p-chlorophenol (129 ppm) were studied using Loeb-Sourirajan-type porous cellulose acetate membranes, and single-solute aqueous feed solutions at 500 psig and the indicated solute concentrations. It was found that, by dissociating the solute by changing the pH of the feed solution, all the above phenols could be separated by reverse osmosis. Solute separation increased with increase in the degree of dissociation of the solute in the feed solution; and, by the appropriate choice of pore size on the membrane surface, separations of phenol approaching the degree of dissociation of phenol in the feed solution could be obtained under the operating conditions used. Similar experiments using aniline (93 ppm) as the solute showed that dissociation of solute molecules in the feed solution could be a technique generally applicable for the reverse osmosis separation of nonionic solutes in aqueous solution. The effects of operating pressure in the range 250 to 1500 psig and pore size on the membrane surface on the separation of un-ionized phenol and p-chlorophenol showed that, with respect to single-solute aqueous feed solutions of phenols, the component whose relative acidity was greater was preferentially sorbed at the cellulose acetate membrane—aqueous solution interface, and the solute concentration in the membrane-permeated product solution was a function of the extent and mobility of each of the sorbed species.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

High thermal stable thermoplastic-thermosetting polyimide film by use of asymmetric dianhydride (a-BPDA)

In order to obtain thermoplastic (before curing) and thermosetting (after curing) polyimides with high T_g for adhesive film, we prepared novel polyimides having phenylethynyl group in the side chain (44% of concentration of curing group) from asymmetric 2,3,3′,4′-biphenyltetracarboxylic dianhydride (a-BPDA), 3,4′-oxydianiline (3,4′-ODA) or 1,3-bis(4-aminophenoxy)benzene (1,3,4-APB) or 1,3-bis(3-aminophenoxy)benzene (1,3,3-APB), and 2,4-diamino-1-(4-phenylethynylphenoxy)benzene (mPDAp). Among three kinds of polymer, uncured polyimide of a-BPDA/1,3,4-APB; mPDAp had rather high T_g (265 °C, DMA) and thermoplasticity (E′ drop>10³ at T_g). After curing reaction of phenylethynyl group, the T_g of the polyimide was increased dramatically (364 °C, DMA). The polyimide derived from 1,3,4-APB having less concentration of curing group (20%) was also prepared to improve further film flexibility and toughness.     

Hydrothermal Formation of Hydroxyapatite Layers on the Surface of Type-A Zeolite

Type-A zeolite evenly covered with hydroxyapatite thin layers was prepared using hydrothermal treatment at 120°C for 8 h under autogenous pressure. The hydroxyapatite needlelike nanocrystals, 100–200 nm in diameter and 30 nm in thickness, were grown under the reaction between discharged Ca²⁺ ions from type-A zeolite and PO₄³⁻ ions in (NH₄)₃PO₄ solution. The preferential orientations of the c -axis of hydroxyapatite crystals perpendicular to a zeolite surface were observed using transmission electron microscopy. The crystal structure of type-A zeolite was not destroyed under the reaction, but the surface morphology was changed only with complete covering of scaly hydroxyapatite particles.     

Polymeric phosphonium salts as a novel class of cationic biocides. VII. Synthesis and antibacterial activity of polymeric phosphonium salts and their model compounds containing long alkyl chains

Various polymeric phosphonium salts containing long alkyl chains (C₁₀? C₁₈) and their corresponding model compounds were prepared, which possess the same hydrophobic structure as that of the common disinfectants (quaternary ammonium salts), and their antibacterial activities were evaluated by means of the viable cell counting method against Staphylococcus aureus (Gram-positive) and Escherichia coli (Gram-negative). The polymer with the decyl group exhibited a higher activity than that of the corresponding model compound, particularly against the Gram-positive strain. Furthermore, antibacterial activity of the polymers was found to decrease as the chain length increased. In contrast with the polymers, the antibacterial activity of the corresponding model compounds increased as hydrophobicity of the substituents increased. The antibacterial activity was strongly dependent on the structure, particularly on the length of the alkyl chain. © 1994 John Wiley & Sons, Inc.     

A model for the complex permittivity of water at frequencies below 1 THz

Experimental permittivity data of liquid water, compiled from the open literature, were selectively applied to support a modeling strategy. Frequencies up to 1 THz and atmospheric temperatures are covered with an expression made up by two relaxation (Debye) terms. The double-Debye model reduces to one term when the high frequency limit is set at 100 GHz, and the model can be extended to 30 THz by adding two resonance (Lorentzian) terms. The scheme was carried out by employing nonlinear least-squares fitting routines to data we considered reliable.     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

Quantitative determination of corrosion products and adsorbed water on copper in humid air containing SO2 by IR-RAS measurements

The time dependency of the amounts of corrosion products and co-existing adsorbed water on copper in humid air containing SO₂ was estimated from a series of in situ time-resolved IR-RAS spectra on the basis of the relations between the band intensities and the mass changes of the corrosion products, which were determined by simultaneous measurement of IR-RAS and QCM. The amounts of both corrosion products increased slowly at the initial stage and later increased rapidly. Although the relative humidity was kept constant, the amount of adsorbed water increased nearly the same behavior as that of corrosion products in the stage of relatively small amounts of corrosion products and later increased rapidly when the amounts of corrosion products increased. In humid air without SO₂, sulfite gradually decomposed and some of it changed into sulfate.     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.