Prediction of spectral reflectance factor distribution of automotive paint finishes

It is necessary to determine the accurate reflectance of painted surfaces for the review of paint finishes by computer graphics (CG) before actual painting of the exterior color of automobiles, and for quality control during production and inspection processes. We have optimized a method for measuring reflectance by using a statistical technique. We have found that the reflectance of a painted surface is best measured at an incident angle of 60° and at five aspecular angles of 10°, 18°, 28°, 40°, and 90°. Our method makes it possible to accurately reproduce reflection characteristics of paint finishes containing special flake pigments, such as pearl mica. Also it was proved that our method can apply not only to solid and metallic coatings but to all painted surfaces. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 275–282, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20125     

A 6-ns ECL 100 K I/O and 8-ns 3.3-V TTL I/O 4-Mb BiCMOS SRAM

The authors report a 4 M word×1 b/1 M word×4 b BiCMOS SRAM that can be metal mask programmed as either a 6-ns access time for an ECL 100 K I/O interface to an 8-ns access time for a 3.3-V TTL I/O interface. Die size is 18.87 mm×8.77 mm. Memory cell size is 5.8 μm×3.2 μm. In order to achieve such high-speed address access times the following technologies were developed: (1) a BiCMOS level converter that directly connects the ECL signal level to the CMOS level; (2) a high-speed BiCMOS circuit with low threshold voltage nMOSFETs; (3) a design method for determining the optimum number of decoder gate stages and the optimum size of gate transistors; (4) high-speed bipolar sensing circuits used at 3.3-V supply voltage; and (5) 0.55-μm BiCMOS process technology with a triple-well structure     

Deposition of carbon films by electrolysis of a water-ethylene glycol solution

An attempt was made to deposit carbon films by electrolysis of a water-ethylene glycol solution. Carbon plate and an n-type silicon substrate were dipped in the solution and a high d.c. potential was negatively applied on the silicon substrate. Some deposits were observed in the region between the boiling point curve and the line approximately 50 °C below and parallel to the boiling point, when electrolysis was carried out at 1 kV for 6 h. For higher potentials of 1.4–2.0 kV and longer electrolysis of 12 h, some samples showed a broad X-ray diffraction peak and Raman peaks, corresponding to graphitic carbon.     

New color TV cameras for ultraviolet, near infrared and visiblelight

Two kinds of TV cameras have been developed that are capable of showing the wavelengths of ultraviolet, infrared, and visible light by means of a false color method. One is sensitive to wavelengths from 250 to 650 nm (ultraviolet to yellow). It can simulate the color vision of the honey bee and other insects, reproducing the nectar guide of a flower or displaying the sex of a cabbage white moth, which is indistinguishable to the naked eye. The other is sensitive to a wider wavelength of 250 to 1,050 nm (ultraviolet to near infrared). According to the filter selected, it obtains not only visual images of invisible light information but also pictures same as those from an ordinary color camera. These TV cameras can be applied in many fields, including science, art, medicine, and industry     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Model for the potential barrier depth along the grain boundaries of an ultrathin tin dioxide gas sensor

A potential barrier model along the grain boundaries in ultrathin tin dioxide (SnO₂) gas sensors is presented. It is assumed that the negatively charged oxygens are adsorbed only on the grain boundaries. The potential barrier depth is expressed as functions of grain size, donor concentration and surface coverage of adsorbed oxygen ions at the boundaries. A direct consequence is that the conduction electrons are effectively confined in a grain when the film thickness becomes smaller than a critical value. This indicates a drastic increase in resistivity with decreasing film thickness in air, and thus an occurrence of an extremely high gas sensitivity.     

Inter- and intra-molecular ionic interactions of polyampholyte: Carboxymethyl-2-diethylaminoethylcellulose

Carboxymethyl-2-diethylaminoethylcellulose (CM-DEAE cellulose) was prepared by etherification of carboxymethylcellulose with diethylaminoethyl chloride in a NaOH solution. The behaviour of CM-DEAE cellulose in aqueous solution was studied by viscosity and GPC measurements. The degree of substitution (DS) and existing states of DEAE substituents were examined by the use of proton NMR, and those of the CM substituents were observed with FT-IR. The results reveal that the reduced viscosity and apparent molecular size of CM-DEAE cellulose vary with the concentration of sodium chloride and changes in pH and DS. These phenomena can be explained in terms of inter- and intra-molecular ionic interactions.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

A 220-MHz pipelined 16-Mb BiCMOS SRAM with PLL proportionalself-timing generator

This 512 Kw×8 b×3 way synchronous BiCMOS SRAM uses a 2-stage wave-pipeline scheme, a PLL self-timing generator and a 0.4-μm BiCMOS process to achieve 220 MHz fully-random read/write operations with a GTL I/O interface. Newly developed circuit technologies include: 1) a zig-zag double word-line scheme, 2) a centered bit-line load layout scheme, and 3) a phase-locked-loop (PLL) with a multistage-tapped ring oscillator which generates a clock cycle proportional pulse (CCPP) and a clock edge lookahead pulse (CELP)