Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Application of polymerizable surfactant in the preparation of polystyrene/nano-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> composite

Monooctadecyl maleate, as a polymerizable surfactant, was synthesized by the mono-esterification of maleic anhydride and octadecanol, and was utilized to surface-modify nano-Fe₃O₄ particles. A polymerizable magnetic fluid was obtained by directly dispersing modified nano-Fe₃O₄ particles into styrene monomer, and the polystyrene/nano-Fe₃O₄ composite was prepared through free radical polymerization of polymerizable magnetic fluid. The structure and dispersion status in different dispersion phases of modified nano-Fe₃O₄ particles were studied by Fourier transform infrared (FTIR) spectrometry, X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The experimental results show that the nano-Fe₃O₄ particles modified by monooctadecyl maleate with the size of about 7–10 nm can be uniformly dispersed into styrene and fixed in the composite during the procedure of polymerization. Thermogravimetric analysis (TGA) and vibrating sample magnetometry (VSM) indicate that the thermal stability of polystyrene/nano-Fe₃O₄ composite is improved compared to that of pure polystyrene, and the composite is a sort of superparamagnetic materials.     

Preparation of highly crystalline nanofibers on Fe and Fe-Ni catalysts with a variety of graphene plane alignments

The present study confirmed that highly crystalline nanofibers with controlled structure may be prepared over Fe and Fe-Ni alloy catalysts. The degree of graphitization of various carbon nanofibers (CNFs) was analyzed by using C(0 0 2) peaks from the XRD profiles. The C(0 0 2) peaks of CNFs over Fe catalyst shifted to higher angle and became narrower as the preparation temperature increased from 560 to 620 °C. Tubular CNFs prepared at temperature higher than 630 °C showed lower 2θ angles compared to those of platelet fibers. CNFs prepared over Fe-Ni catalysts tended to resemble those prepared over Fe catalysts. The degree of graphitization of platelet CNFs resembled natural graphite, while d_0 0 2 of the tubular CNFs showed values below the 3.39 Å reported as a theoretical minimum for a cylindrical alignment. Lc_0 0 2 of platelet and tubular CNFs increased by heat treatment at 2000 and 2800 °C though d_0 0 2 changed little. A transverse section of platelet and tubular CNFs had a hexagonal shape, not a round shape. The hexagonal column allows AB stacking of hexagonal planes that can give perfect hexagonal alignment.     

Phase separation behavior and morphology development of phenolic resin/PMMA/hexamethylenetetrarnine blends

Summary In order to obtain materials with nanopores which will be applicable for many fields, the structures of the cured blends of phenolic resin (PhN), poly(methyl methacrylate) (PMMA) and curing agent were studied. After PMMA was extracted from cured blends, the structures of cured phenolic resins were observed with SEM. As a results, it was found that nanosized continuous pore structures were formed in extremely wide composition region if curing temperature was high.     

Effect of molecular weight on molecular orientation and morphology of polypropylene sheets containing a β-nucleating agent

In this study, polypropylene (PP) films containing the β nucleating agent, N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide, were prepared using PP with three different molecular weights (low, medium, and high) by extrusion process with T-shaped die. The structure and morphology of the films were studied after stretching. It was found that a unique molecular orientation, in which both the c-axis and crystalline lamellae were oriented perpendicular to the flow direction, was formed in all undrawn film samples, irrespective of the molecular weights of the PP. In the PP sheets stretched in the machine direction, the low-molecular-weight sample containing the nucleating agent exhibited brittle properties owing to a lack of tie chains in the stretching direction. In contrast, cavitation was prominent in the medium (M-PP)- and high (H-PP)-molecular-weight samples. Notably, M-PP containing the nucleating agent, with a high degree of molecular orientation, promoted the formation of a large number of voids. In H-PP containing the nucleating agent, the presence of numerous tie chains inhibited cavitation, resulting in fewer voids. The experimental results demonstrated the influence of the molecular weight on the void structure, which will be useful in the field of microporous membranes.     

Hydrogen entry into steel during atmospheric corrosion process

Hydrogen entry and permeation into iron were measured by an electrochemical method during atmospheric corrosion reaction. The hydrogen permeation was enhanced on passive films because the hydrogen adsorption increased by the hydrogen evolution mechanism which is different from that on a bear iron surface. The permeation rate during a wet and dry corrosion cycle showed a maximum in the drying process depending upon the surface pH and the corrosion potential. The pollutant such as Na₂SO₃ which decreases the pH and the corrosion potential causes an increase in the permeation rate. The mechanism of the change in the permeation rate during the wet and dry cycles is explained by the polarization diagram of the electrode covered by thin water layer.     

Adaptive interpolation scheme for NURBS curves with the integration of machining dynamics

This paper develops a comprehensive interpolation scheme for non-uniform rational B-spline (NURBS) curves, which does not only simultaneously meet the requirements of both constant feedrate and chord accuracy, but also real-time integrates machining dynamics in the interpolation stage. Although the existing work in this regard has realized the importance to simultaneously consider chord error and machining dynamics, none has really incorporated these in one complete interpolation scheme. In this paper, machining dynamics is considered for three aspects: sharp corners or feedrate sensitive corners on the curves, components with high frequencies or frequencies matching machine natural ones and high jerks. A look-ahead module was developed for detecting and adaptively adjusting the feedrate at the sharp corners. By Fast Fourier Transform (FFT) analysis with a moving window in the interpolation stage identified were some special frequency components such as those containing high frequencies or with frequencies matching machine natural ones. Then, the notch filtering or time spacing method was used to eliminate these components. To more completely reduce feedrate and acceleration fluctuations, the jerk-limited algorithm was also developed. Finally, the interpolated feedrate was further smoothened with B-spline fitting method and the NURBS curves were re-interpolated with the smoothened feedrate. During the interpolation, the chord error was repeatedly checked and confined in the prescribed tolerance. Two NURBS curves were used as examples to test the feasibility of the developed interpolation scheme.     

Gas barrier properties and periodically fractured surface of thin DLC films coated on flexible polymer substrates

Thin DLC films coated on polymer surfaces are attracting considerable attention due to their wide applications and their interesting surface properties. When DLC films were coated on polymers, the resulting DLC-polymer composites are highly functionalized materials, some of which presenting dramatically improved gas barrier properties.In this paper, we will introduce several commonly used polymers including polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) for semi-crystalline polymers, and polymethyl methacyrlate (PMMA) for an amorphous polymer. The polymers were coated with thin DLC films and the gas barrier properties of the resulting DLC-polymer composites were investigated. Some of the DLC-polymer composites dramatically improved their gas barrier properties while they presented horizontal crack lines and vertical micro-buckling lines on the DLC surface when stretched to a certain strain. The gas barrier properties of the DLC-polymer composites with fractured DLC surface were also studied. It was found that the gas barrier property of the polymer substrates with lower residual strains was less damaged, when the substrates were mechanically deformed, than that of the polymer substrates with higher residual strains. When the number of the cracks increases, the strain imposed on each crack decreases, since the overall deformation is almost equally distributed to each crack while the crack spacing of each crack becomes shorter. Thus, it was found that the degradation of the gas barrier property after mechanical deformation is dependent on the residual strain of the polymers and the number of cracks on DLC films.     

Development of the remote-controlled platform truck for handling heavy object and the remote control human interface for the disaster response

General interest for robotic technology has been increased by the public and the media after Fukushima Daiichi Nuclear Power Plant (hereafter referred to as 1F) disaster. Especially, robots which can work under the very severe condition where personnel cannot access have demands for development. As to respond to such high demands, NEDO established ‘Disaster response unmanned systems development project’ in 2012.[1] This project is specialized in the development of various remote-controlled equipment, such as remote-controlled platform truck and remote control human interface under ‘Mobile Robot Development’. Remote-controlled platform truck is designed to safely and surely deliver robots and supplies, instead of using stairs and elevator, etc. in and out of building where it is too critical for personnel to work under. Remote control human interface for robots is designed to standardize the command and operation screen for operator, based on opinions from project members, and manned facility construction.[2] In this article, mechanical structure and development tasks for remote-controlled platform truck, and commonalization approach for operation and camera display of various remote-controlled equipment and robot for remote control human interface are stated. Background: due to hydrogen explosion triggered by The Great East Japan Earthquake on 11 March 2011, a reactor building at Fukushima Daiichi Nuclear Power Plant was severely damaged. It is required to reduce high radiation dose in the atmosphere of the reactor building to perform restoration. To pursue decontamination of the reactor building, equipment to lift and carry decontamination devices to upper floor are required.     

Repeatedly foldable AMOLED display

In this study, a 5.9‐inch foldable active‐matrix organic light emitting diode (AMOLED) display was developed. A folding test was performed repeatedly. The display survived the folding test (100,000 folds) with a curvature radius of 2 mm. To protect an organic light emitting diode (OLED) against moisture, inorganic passivation layers are provided on the upper and lower sides of the flexible display. Using our transfer technology, high density passivation layers can be obtained. The measured water vapor transmission rate of the layer is 7 × 10^?6 g/m²?day or less, which improves OLED reliability. With these techniques, we have developed a book‐type display, which is repeatedly foldable like a book, and a tri‐fold display including a display area, which is foldable in three.