Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.     

Use of colloidal ruthenium particles in the electrochemical reduction of benzene by solvated electrons

Ruthenium colloidal particles prepared by the decomposition of a ruthenium acid sulfite complex increased the electrochemical reduction of benzene from 45% to 60% at room temperature and 10 psig of hydrogen. The reduction was carried out in a 21 mole % ethanol - 79 mole % hexamethylphosporamide. The significant increase in the percent of benzene reduced was accompanied by an apparent current efficiency of 98%. Comparison with analogous experiments employing colloidal platinum particles indicates that the above increase in benzene reduction can be attributed to direct catalytic hydrogenation by the ruthenium.     

Efficient compensation for frequency-dependent errors in analog reconstruction filters used in IQ modulators

In a direct-conversion transmitter system, the nonideal transfer characteristics of practical analog subsystems can have significant adverse effects on the performance of the transmitter system. While a significant body of research exists on correcting static errors (including gain imbalance, phase errors, and DC offsets) in the analog subsystems, relatively little attention has been paid to the impact of nonideal frequency-dependent characteristics in the analog reconstruction filters that are employed in direct-conversion structures. This paper presents a new computationally efficient and numerically robust method for automatic digital compensation for nonideal frequency-dependent characteristics in the signal reconstruction filters of a quadrature (IQ) modulator structure. The new compensation technique is used in conjunction with existing compensation approaches that compensate for static errors.     

Minimum-energy multicast in mobile ad hoc networks using network coding

The minimum energy required to transmit one bit of information through a network characterizes the most economical way to communicate in a network. In this paper, we show that, under a layered model of wireless networks, the minimum energy-per-bit for multicasting in a mobile ad hoc network can be found by a linear program; the minimum energy-per-bit can be attained by performing network coding. Compared with conventional routing solutions, network coding not only allows a potentially lower energy-per-bit to be achieved, but also enables the optimal solution to be found in polynomial time, in sharp contrast with the NP-hardness of constructing the minimum-energy multicast tree as the optimal routing solution. We further show that the minimum energy multicast formulation is equivalent to a cost minimization with linear edge-based pricing, where the edge prices are the energy-per-bits of the corresponding physical broadcast links. This paper also investigates minimum energy multicasting with routing. Due to the linearity of the pricing scheme, the minimum energy-per-bit for routing is achievable by using a single distribution tree. A characterization of the admissible rate region for routing with a single tree is presented. The minimum energy-per-bit for multicasting with routing is found by an integer linear program. We show that the relaxation of this integer linear program, studied earlier in the Steiner tree literature, can now be interpreted as the optimization for minimum energy multicasting with network coding. In short, this paper presents a unifying study of minimum energy multicasting with network coding and routing.     

Evaluating the application of a decision support system in identifying adequate wastewater treatment for small communities. A case study: the Fluvia River Basin.

The identification of adequate wastewater treatment for small communities is a complex problem since it demands a combination of data from different sources, such as aspects of the community and landscape, the receiving environment and the available wastewater treatment technologies. The Catalan Water Agency (Agència Catalana de l'Aigua) considered using an EDSS (Environmental Decision Support System) as a tool to help water managers select the most adequate treatment for the urban wastewater of nearly 3,500 small communities in Catalonia (Spain). From that moment, EDSS was applied to all the river basins in Catalonia. In this paper the authors present the results obtained for the 76 small communities located in one of these river basins: the Fluvia River Basin. The characteristics of the community used in the reasoning process of the EDSS, the list of selected wastewater treatment alternatives, the technical environmental justification for the selected treatments and the reasons for discarding, favouring or disadvantaging them are presented. Finally, some results for the Fluvia River Basin are compared with those obtained in other Catalan river basins with different characteristics in order to evaluate which are the significant features in identifying adequate wastewater treatments.     

Hydrologic regionalisation impacts on wet-weather control selection.

Continuous simulation is performed using the US Environmental Protection Agency (USEPA) Storm Water Management Model (SWMM) to evaluate regional differences around the United States in hydrologic and water quality performance of wet-weather controls. Controls are characterised as being limited by peak inflow rate (i.e. any device with little or no storage, such as screens, filters and some proprietary devices) or by storage capacity (e.g., ponds, tanks). For flow-limited devices, results are presented in the form of percentage of annual runoff volume captured (passing through the device) for a given inflow capacity. For storage-limited devices, results are presented in two forms: percentage of annual runoff volume captured as a function of unit basin size and drawdown (drain) time, and as a percentage of total suspended solids captured, for the same two variables. Regional differences are apparent, driven mainly by variations in rainfall patterns around the country.     

Processes of the Collision Interaction between Ceramic Particles Being Crushed in a Circulation Pneumatic Crusher

A new circulation pneumatic crusher capable of producing submicron powders of refractory materials is presented. A mathematical model is constructed for the dynamic breaking of ceramic macroparticles. This model allows the basic laws of shock-wave crushing in the circulation pneumatic apparatus to be analyzed.__________Translated from Teoreticheskie Osnovy Khimicheskoi Tekhnologii, Vol. 39, No. 3, 2005, pp. 327–333.Original Russian Text Copyright © 2005 by Belov, Biryukov, Roslyak, Yugov, Afanas’ev.     

Concurrent effect of microporosity and chemical structure on the equilibrium sorption properties of cellulose-based hydrogels

Polyelectrolite hydrogels are crosslinked polymers which display high sorption capacity in water and water solutions. They are widely used in the marked of personal hygiene products, as well as in other biomedical and industrial applications. In the most industrial application they are not biodegradable and prepared starting from acrylamide.In this work, the chemical-physical analysis of a novel class of natural polymers-based microporous superabsorbent hydrogels has been presented. The main focus is the definition of the relationship between material's chemical-physical structure and its equilibrium sorption properties.The effect of the variation of the degree of crosslinking, the polyelectrolyte nature of the backbone and the hydrogel microporosity on its swelling properties has been analysed, and a good agreement with the theoretical statements has been displayed.The effect of the ionic strength and the pH of the external solution in contact with the hydrogel on its equilibrium sorption properties has also been assessed, and an high sensitivity to these variations was detected for all the tested chemical compositions and physical structures.This work have to be considered part of the efforts towards the reduction of the environmental impact of the large scale consumption industrial polymer based products.     

Interfacial strength and chemistry of additive-free silicon nitride ceramics brazed with aluminium

Two kinds of additive-free silicon nitride ceramics were brazed with aluminium; one was with as-ground faying surfaces and the other was with faying surfaces heat-treated at 1073K for 1.8 ksec in air. The heat-treatment of the silicon nitride ceramics formed a silicon oxynitride layer on the faying surfaces and increased the brazing strength of the joints. A silica-alumina non-crystalline layer and a β′-sialon layer were formed successively from the aluminium side at the interface of the joints. The heat-treatment which made the former layer thicker is a necessary process in making reliable, strong brazed joints.