Purification of Ellagic Acid by UF Membranes

Ellagic acid (2, 3, 7, 8‐tetrahydroxy(1)benzopyrano(5, 4, 3‐cde)(1)benzopyran‐5, 10‐dione) was selected as a model pollutant which is present in the tannic fraction of cork processing wastewater. The ultrafiltration of aqueous ellagic acid solutions through three membranes was studied in tangential UF laboratory equipment. Two of the membranes were polyethersulfone (Biomax10K and Biomax5K, with MWCO of 10000 and 5000 Da, respectively), and the third made of regenerated cellulose (Ultracel5K, with MWCO of 5000 Da). The water hydraulic permeability was evaluated for each membrane. The evolution of the permeate flow rate with processing time was followed, and the influence of the main operating variables (feed flow rate, trans‐membrane pressure and nature of the membranes) on the permeate flux was also established. According to the hypothesis of the film theory, the intrinsic and apparent rejection coefficients, as well as the mass transfer coefficients, were also determined, and the values obtained were discussed as a function of the operating conditions used.     

Development of a Ceramic Micro Heat Exchanger – Design,Construction, and Testing

This article presents the development of a ceramic micro heat exchanger. Starting from its geometrical design, results obtained from a simplified simulation of the heat exchanger efficiency will be given. The alumina microcomponents were manufactured by a rapid prototyping process chain. Here, stereolithography was combined with a low‐pressure injection molding process for the rapid and precise manufacturing of ceramic components down to the micrometer range. A micro heat exchanger, joined from sintered components using a glass solder, was applied as a prototype and checked for its performance at a system pressure of 8 bar.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

A case study of regional catchment water quality modelling to identify pollution control requirements.

There are four ecologically important river catchments that contain candidate Special Areas of Conservation (cSACs) under the Habitats Directive in the Lake District National Park located in the North of England. These are the rivers Ehen, Kent, Derwent and Eden. For each cSAC, there are defined ecological criteria that include water quality targets to protect the designated species. Stretches of the riverine cSACs in each catchment are failing to meet these and other water quality targets. The Environment Agency commissioned a study of each catchment to provide the underpinning scientific knowledge to allow it to deliver its statutory obligations under the Habitats Directive. SIMCAT river water quality models were produced and used to predict the water quality impacts resulting from a number of water quality planning scenarios aimed at achieving full compliance with the Habitats Directive and other national and EEC water quality targets. The results indicated that further controls on effluent discharges will allow the majority of targets to be met but other sources of pollution will also need to be controlled. The outcome of the study also recognised that water quality improvements alone will not necessarily produce the required improvement to the ecological interest features in each cSAC.     

Structure and Certain Properties of Hot-Pressed Boron Carbide-Based Ceramic with Calcium-Silicon Additive

The influence which the composition of powder mixtures, the treatment conditions which the mixtures are subjected to, and the conditions under which the hot-pressed composite materials B₄C – (5-10 mass%) calcium-silicon are fabricated exert on the structure, nature of failure, and mechanical properties of these materials is investigated. Optimum properties are possessed by material containing 10 mass% of addition. It is shown that the structure, morphology, and dispersivity, as well as the nature of the distribution of the components that are added to the composite material (secondary phase) vary as the temperature of hot pressing changes. Maximal mechanical characteristics of the composite material (σ_bend = 560 MPa, K _1c = 4.7 MPa·m^1/2, HV = 37 GPa) are attained at hot-pressing temperatures in the range 2000-2100°C.     

Agility through discipline: a debate

While Beck asserts that agility is only possible through greater discipline on the part of everyone involved, Boehm counters that you don't broaden the definition of "discipline" by rejecting parts of it. Yet, from inside extreme programming, it seems that the only way to achieve the desired results is to view the world in 'both-and" terms instead of "either-or" terms.