Compartment tests of polyurethane foam seating assemblies

Data from compartment tests of polyurethane foam seating assemblies are reported. Results show that the behavior of such assemblies during fires is strongly dependent on the type and position of interliners and upholstery fabrics. An incidental comparison of peak rate of heat release obtained in a compartment test with a predictive model equation is made and selected data from the tests are presented.     

Geomechanical model simulation for the varied rock formations of the Kadana dam foundation,Gujarat, India

Bulletin of Engineering Geology and the Environment - Precambrian layered rocks consisting of quartzites, phyllites and metagreywackes of the Aravallis having a large variation in thickness,...     

The development of macrolayer thickness of water in the pool boiling regime

ABSTRACT

The main purpose of this study is to analyse the phenomenon of pool boiling in water over a horizontally placed copper tube heater of 28?mm diameter. The experiment has been carried out to observe the bubble growth and departure characteristics for the heat flux range up to 40,000?W/m². The entire process is being recorded by a digital camera at different time intervals. The measured parameters have been used to determine the initial layer thickness, macro layer thickness and critical heat flux and validated with models proposed in the literature.     

Book reviews

The Annals of Regional Science -     

Antimicrobial multiresistance in bacteria isolated from freshwater Chilean salmon farms

The intensive use of antimicrobial agents, mainly oxytetracycline, to prevent and control bacterial pathologies in Chilean salmon culture is a frequent practice. A total of 103 gram-negative oxytetracycline-resistant bacteria recovered from various sources of 4 Chilean freshwater salmon farms were identified and investigated for their susceptibility patterns to various antibacterial agents, by using an agar disk diffusion method. Antibacterial resistance patterns of isolates were not correlated with bacterial species or strain source. A high number of bacteria resistant to amoxicillin, ampicillin. erythromycin, and furazolidone, as well as an important frequency of bacterial resistance to florfenicol, chloramphenicol, cefotaxime and trimethoprim-sulfamethoxazole was found. On the contrary, the proportion of bacteria resistant to gentamicin, kanamycin, flumequine and enrofloxacin was rather low. Resistant microflora showed a high taxonomic variability and mainly consisted of non-fermenting bacteria (77.7%). These strains mainly belonged to the species Pseudomonas fluorescens (29), Aeromonas hydrophila (10), Stenotrophomonas maltophilia (6), isolated from salmon fingerlings, and Acinetobacter lwoffii (5) isolated from pelletized feed. The occurrence of simultaneous resistance to various antibacterials was frequent. We observe a high frequency of bacteria resistant to 6-10 antibacterials (74 strains), and antibiotic resistance index (ARI) values ranging from 0.38 to 0.48 for the four salmon farms studied. These results suggest that Chilean salmon farms might play a role as reservoirs of antibacterial multiresistant bacteria, thus prompting the necessity for a more restrictive attitude towards the intensive use of antibacterials in salmon farming.     

A semiautomated procedure for the determination of phosphorus in water, waste waters and particulates

Improved procedures for the determination of total dissolved phosphorus (TDP), particulate phosphorus (PP) and dissolved inorganic orthophosphate (DP) are described. Organic particulate material is solubilized in 5 n NaOH, and phosphorus compounds are oxidized and mineralized to orthophosphate by persulfate digestion. DP is determined by an improved automated molybdenum blue procedure that does not require sample pH adjustment or a correction for silicate interference in the 0–50 mg Si 1^?1 range. The use of 36-position digestion racks allows 32 TDP or PP samples to be digested in ca. 1 and 4 h respectively. Detection limits in μg of phosphorus 1^?1 are DP, 2; TDP, 5; and PP. 1. Waste water samples were analyzed for TDP and PP by the nitric acid-sulfuric acid procedure and by the proposed method. There was no significant difference between the two sets of data (P > 0.45).     

Results of evaluation of the strength of concrete placed in the shafts of cast-in-place piles

Conclusions 1. Application of the method of underwater concreting with the use of a container is inexpedient in connection with the presence of a large number of flaws detected in the shafts of cast-in-place piles formed by this method; concreting of holes by the VAT method is preferable.2. The strength of concrete in the shafts of cast-in-place piles increases, reaching a maximum at a depth of 0.4–0.5 the length of the shaft. Variation in strength along the shaft is explained primarily by the percentage of coarse aggregate contained in the concrete.3. The quality of pile concrete should be monitored during all stages of pile installation, and, primarily during the stage of concreting, i.e., when there is a chance of correcting an observed defect.All-Union Institute for the Design and Planning of Health Resorts. Scientific-Research Institute of Foundations and Underground Structures. Translated from Osnovaniya, Fundamenty i Mekhanika Gruntov, No. 5, pp. 14–17, September–October, 1976.     

A digital wind gust recorder

The instrument was a byproduct of an undergraduate final year project on wind power which was carried out by the Department of Mechanical Engineering of the University of Liverpool.The windmill test site was on an exposed, rocky island where there was no history of weather recording but a long tradition of violent winds.Field experience during the winter months suggested that corrosion fatigue arising from wind buffeting and salt spray would rank equally with maximum wind pressure as criteria of failure and if modern materials, so convenient for forming aerodynamic surfaces, were to be used then limited life concepts would need to be considered. This called for more knowledge of wind variations at the test site. A complete wind spectrum taken on chart recording instruments would have been ideal but since such such refined devices were not available the instrument to be described was designed.The only wind measuring instrument which was available was a rotating cup anemometer. This supplied an alternating voltage proportional to its rotational speed. It also operated a gear driven microswitch which could give an integrated “miles of wind” reading on an electromagnetic counter.Briefly the e.m.f. generated by the anemometer (Fig. 1) was matched against a pre-set voltage corresponding to the required gust velocity. When this was exceeded an appropriate counter was operated. Only the rising e.m.f. was significant. The subsequent fall was ignored. Initially three stages were incorporated which reported the gusts rising through forty, fifty and sixty knots, respectively. These recorded on separate counters. All basic settings were based on pitot-static speed determinations in a wind tunnel.     

Combined biological and ozone treatment of log yard run-off

Batch biological treatment of log yard run-off reduced biochemical oxygen demand (BOD), chemical oxygen demand (COD) and tannin and lignin (TL) concentration by 99%, 80%, and 90%, respectively. Acute (Microtox) toxicity was decreased over treatment, from an initial EC50 of 1.83% to a value of 50.4% after 48 h of treatment. Kinetics of biodegradation were determined using respirometry and fitted using the Monod and Tessier model. For the Monod model the maximum substrate uptake rate, and Ks values determined were 0.0038 mg BOD/mgVSS min, and 1.4 mg/L, respectively. The efficacy of ozone as a pre- and post- biological treatment stage was also assessed. During ozone pretreatment, TL concentration and acute toxicity were rapidly reduced by 70% and 71%, respectively. Pre-ozonation reduced BOD and COD concentration by < 10%, however a larger fraction of residual COD was non biodegradable after ozonation. Biologically treated effluent was subjected to ozonation to determine whether further improvements in effluent quality could be achieved. A reduction in COD and TL concentration was observed during ozonation, however no further improvement in toxicity was observed. Ozonation increased BOD by 38%, due to conversion of COD to BOD.