Preparation and properties of CdS thin films prepared on cold substrate as a window layer for solar cells

CdS films, usually, prepared on hot substrate at temperature range from 180 to 220°C. The electrical properties of the films are dependent on many parameters such as film thickness, deposition rate, film structure and substrate temperature. To control all these parameters to get film resistivity suitable for manufacturing solar cells, it needs a lot of precautions. CdS prepared on cold substrate could be the solution for this problem. Evaporation of CdS film at constant evaporation rate, then annealed in open air up to 600°C according to the film thickness. The resultant film have been studied. The properties of the films were comparable to the films prepared by the other methods with less control complexity.     

Prevention of tooth hypersensitivity caused by the hydrodynamic action of zinc phosphate and composite resin luting cements (SEM) study

This study was done to determine the role of cement liner as a reducing factor to the fluid movement in order to prevent tooth hypersensitivity according to the hydrodynamic theory during cementation of crowns. A total of fourty freshly extracted intact lower molar were selected for this study. After conventional tooth preparation the teeth were sub-divided into four equal groups to identify the role of cement liner in preventing the penetration of used cement into the dentinal tubules. Scanning electron microscopic study proved the efficiency of glass ionomer liner on preventing cement penetration into the dentinal tubules.     

What constitutes cerebral palsy?

OBJECTIVE: To determine whether a newly developed disability scale for patients with neck pain demonstrated acceptable reliability and validity. METHODS: Testing was conducted using three different samples of patients with neck pain (n = 162). Test-retest reliability of the scale was carried out on the same day with one sample (n = 39), and between-day reliability was carried out with another (n = 21). Differential item functioning with regard to the influence of gender and age was carried out with these two patient groups, as was construct validity. Responsiveness was measured using patients participating in a clinical trial involving patients with chronic neck pain (n = 102). Additionally, scale scores were compared with a wide range of physical measurements using the patients in the clinical trial. RESULTS: Short-term, between-day and postal questionnaire reliability coefficients were all extremely high. The Cronbach's alpha coefficient for internal consistency was 0.9 for the entire scale, and the coefficients for individual items were all greater than 0.88. Disability scale scores correlated strongly to pain scores as well as to doctor and patient global assessments, indicating good construct validity. Relative changes in disability scores demonstrated a moderately strong correlation to changes in pain scores after treatment. Scale scores correlated weakly to all physical measurements. CONCLUSIONS: The disability scale demonstrated excellent practicality and reliability. The scale accurately reflects patient perceptions regarding functional status and pain as well as doctor's global assessment and is responsive to change over long periods of time. We feel that this scale can be a valuable tool for the assessment of patients in future clinical trials and quality of care studies.     

Tuning photocurrent response through size control of CdSe quantum dots sensitized solar cells

The photovoltaic characterization of CdSe quantum dots sensitized solar cells (QDSSCs) by tuning band gap of CdSe quantum dots (QDs) through size control has been investigated. Fluorine doped tin oxide (FTO) substrates were coated with 20 nm in diameter TiO₂ nanoparticles (NPs). Pre-synthesized colloidal CdSe quantum dots of different sizes (from 4.0 to 5.4 nm) were deposited on the TiO₂-coated substrates using direct adsorption (DA) method. The FTO counter electrodes were coated with platinum, while the electrolyte containing I^?/I ₃ ^? redox species was sandwiched between the two electrodes. The current density-voltage (J-V) characteristic curves of the assembled QDSSCs were measured for different dipping times, and AM 1.5 simulated sunlight. The maximum values of short circuit current density (J_sc) and conversion efficiency (η) are 1.62 mA/cm² and 0.29 % respectively, corresponding to CdSe QDs of size 4.52 nm (542 nm absorption edge) and of 6 h dipping time. The variation of the CdSe QDs size mainly tunes the alignment of the conduction band minimum of CdSe with respect to that of TiO₂ surface. Furthermore, the J_sc increases linearly with increasing intensity of the sun light, which indicates the sensitivity of the assembled cells.     

Design and testing of high-density polyethylene nanocomposites filled with lead oxide micro- and nano-particles: Mechanical,thermal, and morphological properties

This research discusses the mechanical behavior and the microstructure of high-density polyethylene (HDPE)-based composites, manufactured using the melt-mixing and thermal-pressing techniques, where HDPE is mixed with various percentages of either bulk lead monoxide (bulk PbO) or PbO nanoparticles (PbO-NPs) acting as fillers. The scanning electron microscope and the field emission transmission electron microscope were utilized to identify the morphology of polymeric composites. Both showed the proper dispersion of PbO in the HDPE matrix without substantial agglomerations. The effect of PbO on the thermal behavior of the HDPE was studied using the thermogravimetric analysis. Tensile tests were implemented to find out how the mechanical characteristics of the composites were affected. Yield stress, % elongation at break, stiffness, tensile energy (toughness), ultimate tensile strength, and ultimate tensile strain were elucidated in this work. The values of stiffness, ultimate tensile strength, and yield stress increased by increasing either the bulk PbO or PbO-NPs' loading up to 40.0 wt % with reference to the hosting matrix. The values of ultimate tensile strain, tensile energy, and % elongation at break of the assembled composites diminished dramatically by increasing the filler's content from 10.0 to 50.0 wt %. Besides, composites with PbO-NPs as a filler were identified as having higher mechanical characteristics than those with bulk PbO for the same wt %. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47812.     

Thermo-mechanical properties of high density polyethylene with zinc oxide as a filler

This study investigates the microstructural, thermal, and mechanical behavior of high density polyethylene (HDPE)-based composites prepared using compression molding technique. HDPE was mixed with either micro-size zinc oxide (bulk ZnO) or zinc oxide nanoparticles (nano-ZnO) as fillers’ contents at 0, 10, 20, 30, and 40 wt%. The structural, morphological, and thermal properties of the composites were identified using X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared spectrophotometer (FTIR), and thermal gravimetric analysis (TGA). The results showed good dispersion and interaction mechanisms between HDPE and the fillers at low weight percentage. The thermal stability of HDPE was enhanced by adding both bulk and nano-ZnO, especially for higher filler loading. Tensile tests at different speeds and Vickers microhardness tests conducted at different indentation loads (0.25–5 N) at t = 60 s were performed to realize how the mechanical properties of the composites were influenced. The values of stiffness, ultimate tensile strength, and yield stress increased by increasing the filler loading to 20 wt% of either bulk ZnO or nano-ZnO. The values of ultimate tensile strain and ductility were deteriorated by increasing the filler loading. Nano-ZnO, at 20 wt% content in composite, showed higher mechanical properties than bulk composite, so it has been recommended for a better tensile performance at higher strain rates. Vickers microhardness measurements showed that the tested samples exhibited reverse indentation size effect (RISE) behavior. The obtained results were analyzed using Meyer’s law which was a preferred approach for analysis of HDPE/ZnO composite.     

Plasma Levels of 14:0, 16:0, 16:1n-7, and 20:3n-6 are Positively Associated,but 18:0 and 18:2n-6 are Inversely Associated with Markers of Inflammation in Young Healthy Adults

Inflammation is a recognized risk factor for the development of chronic diseases, such as type 2 diabetes and atherosclerosis. Evidence suggests that individual fatty acids (FA) may have distinct influences on inflammatory processes. The goal of this study was to conduct a cross-sectional analysis to examine the associations between circulating FA and markers of inflammation in a population of young healthy Canadian adults. FA, high-sensitivity C-reactive protein (hsCRP), and cytokines were measured in fasted plasma samples from 965 young adults (22.6 ± 0.1 years). Gas chromatography was used to measure FA. The following cytokines were analyzed with a multiplex assay: regulated upon activation normal T cell expressed and secreted (RANTES/CCL5), interleukin 1-receptor antagonist (IL-1Ra), interferon-γ (IFN-γ), interferon-γ inducible protein 10 (IP-10), and platelet-derived growth factor β (PDGF-ββ). Numerous statistically significant associations (p < 0.05, corrected for multiple testing) were identified between individual FA and markers of inflammation using linear regression. Myristic (14:0), palmitic (16:0), palmitoleic (16:1n-7), and dihomo-γ-linolenic (20:3n-6) acids were positively associated with all markers of inflammation. In contrast, stearic acid (18:0) was inversely associated with hsCRP and RANTES, and linoleic acid (18:2n-6) was inversely associated with hsCRP, RANTES and PDGF-ββ. In conclusion, our results indicate that specific FA are distinctly correlated with various markers of inflammation. Moreover, the findings of this study suggest that FA profiles in young adults may serve as an early indicator for the development of future complications comprising an inflammatory component.     

Biological influence of some crown and bridge restorative materials finished and polished by different techniques

Fixed restorations should satisfy certain biologic requirements and they must not be injurious to the surrounding living tissues as pulp, periodontal ligament, alveolar bone and gingiva. It is best to terminate preparations above the gingival margin but for retention and esthetics considerations the margins of the fixed restorations could be placed subgingivally. In recent years, the biologic effects of dental restorative materials on the gingiva and periodontal tissues have been better appreciated. A rough surface restoration attracts and retains bacterial plaque and irritates the surrounding soft tissues which is injurious to the living supporting structure of the abutments.     

An optimized FP-growth algorithm for discovery of association rules

The Journal of Supercomputing - Association rule mining (ARM) is a data mining technique to discover interesting associations between datasets. The frequent pattern-growth (FP-growth) is an...     

Fast homomorphic SVM inference on encrypted data

Neural Computing and Applications - Kernel methods are popular machine learning methods that provide automated pattern analysis of raw datasets. Of particular interest is Support Vector Machines...