Early Stages of Recrystallization in Equal-Channel Angular Pressing (ECAP)-Deformed AA3104 Alloy Investigated Using Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) Orientation Mappings

Early stages of recrystallization in alloys containing complex structure of second phase particles are of considerable practical interest. They were observed for the AA3104 alloy in which large particles occur against the background of randomly distributed dispersoids. The samples were deformed by equal channel angular pressing and then slightly annealed to obtain the state of partial recrystallization. The highly deformed alloy contained a structure of flat grains with the spacing between high-angle grain boundaries ranging from 100 nm to 1 ??m. On annealing, the structure coarsened and got transformed into nearly equiaxed grains by both discontinuous and continuous recrystallization. The nucleation of new grains was observed in statically recrystallized bulk samples using scanning electron microscopy, and during in-situ recrystallization in a transmission electron microscope. Special attention was paid to the nucleation of new grains in areas close to large second phase particles, where a relatively high stored energy was expected to stimulate nucleation. A particular role in the rise of nuclei is attributed to migration of low angle boundaries. During recrystallization at 623 K (350?°C), in most of the observed cases, the growth of grains occurred by coalescence of neighbouring cells and by migration of high-angle grain boundaries. These processes led to nearly equiaxed grains of similar size. Orientation mappings showed that although orientations of new grains were widely scattered, they were not completely random.     

Reduced strength degradation of alumina–aluminium titanate composite subjected to low-velocity impact loading

The impact behaviour of monophase alumina and alumina–aluminium titanate monolithic composite ceramics that present flaw tolerant behaviour was studied. Low-velocity impact loading tests were performed on bending bars and the residual strength after the impact was evaluated by four-point bending tests. The impact tests were monitored using an instrumented drop-weight machine. During impact, the composites absorbed higher energy than the monophase material. The strength retention, in percentage, after the impact was significantly higher for the composite that presented damage tolerance for impact energy levels higher than monophase alumina. These results are discussed and fractographic analysis was used to identify the mechanisms responsible for the lower strength degradation of the composite.     

Synthesis of monoclinic Celsian from Coal Fly Ash by using a one-step solid-state reaction process

Monoclinic (Celsian) and hexagonal (Hexacelsian) Ba_1?xSr_xAl₂Si₂O₈ solid solutions, where x = 0, 0.25, 0.375, 0.5, 0.75 or 1, were synthesized by using Coal Fly Ash (CFA) as main raw material, employing a simple one-step solid-state reaction process involving thermal treatment for 5 h at 850–1300 °C. Fully monoclinic Celsian was obtained at 1200 °C/5 h, for SrO contents of 0.25 ≤ x ≤ 0.75. However, an optimum SrO level of 0.25 ≤ x ≤ 0.375 was recommended for the stabilization of Celsian. These synthesis conditions represent a significant improvement over the higher temperatures, longer times and/or multi-step processes needed to obtain fully monoclinic Celsian, when other raw materials are used for this purpose, according to previous literature. These results were attributed to the role of the chemical and phase constitution of CFA as well as to a likely mineralizing effect of CaO and TiO₂ present in it, which enhanced the Hexacelsian to Celsian conversion.     

Data Processing and Calibration for an Airborne Scatterometer

The ERASME radar system has been designed to be easily mounted on small helicopters or aircraft. As it is used for research investigations on radar remote-sensing applications, it has to be well calibrated in every configuration, both absolutely and relatively for comparisons at different points of the swath. The data processing is described, which allows for antenna pattern correction and for flight parameters correction (pitch, roll, altitude), as an introduction for the calibration procedures: internal calibration, external calibration on corner reflectors for absolute calibration (within 1 dB), and a statistical approach, which uses experimental data itself and analyzes the correlation between processed data and recorded flight parameters. This method provides a way to check or adjust calibration for specific flight configurations, and allows a relative accuracy of better than 0.5 dB for data comparison within the radar swath. Such a method could be used to calibrate any airborne or spaceborne scatterometer when accurate antenna measurement is not feasible.     

Epilepsy in very preterm infants: neonatal cranial ultrasound reveals a high-risk subcategory

Osteoporotic fractures, and in particular, hip fractures result in significant morbidity and mortality. Low bone mass is the main risk factor of enhanced bone fragility, resulting in an increased risk for hip fracture. Bone density of osteoporotic women with and without hip fractures show a considerable overlap. Therefore, other bone-independent factors also play an important role for the development of hip- and other osteoporotic fractures. One other important factor is falling. In 90% of hip fractures falling was involved [10-15], but only 5% or less of these falls resulted in a subsequent fracture. The view that adequate exercise is beneficial for skeletal health of children and for prevention and treatment of osteoporosis in adults is supported primarily by two lines of evidence: longitudinal and cross-sectional trials in children and young adult athletes showing a significant increase of muscle- and bone mass after strenuous (children) or chronic exercise (athletes) as compared to normally active (children) or sedentary control subjects. What are the potential benefits and limits of specific exercise programs with respect to bone mass, prevention of falls and fractures? In this review these questions are discussed and a specific exercise program in osteoporotic patients with fractures is delineated.     

Interaction of per 3,6-anhydro-alpha cyclodextrins (alpha 36CD) and lead-alpha 36CD complex with biological systems

The interactions of per (3,6 anhydro) alpha cyclodextrin (alpha 36CD) and of lead-alpha 36CD complex with biological systems were tested by NMR, ESR and electronic microscopy using erythrocytes and model membranes. It was found that the haemolytic activity of alpha 36CD alone was seven fold lower than that of natural alpha cyclodextrin (evaluated by the concentration inducing 50% haemolysis, DH50 = 35 mM). Conversely, the formation of the complex resulted in an increase of haemolytic properties, with DH50 of 1 mM. The mechanism proposed was an increased membrane diffusion by endocytosis of the complex, leading to higher amounts of intracellular lead.     

Processing and sintering of a 3 : 2 alumina silica gel

The aim of this work was to investigate the possibility of applying a conventional ceramic processing route to an amorphous mullite precursor. The main processing parameters necessary for high purity and dense mullite bodies were studied. The effect of thermal pretreatments on the sintering mechanism, density and microstructure of mullite compacts was established.