Thermal conductivity of doped PbTe-based solid solutions with off-center impurities

The coefficients of thermopower and electrical and thermal conductivity in the PbTe_0.8Se_0.1 S _0.1 solid solution with electron concentration (4.6–54) × 10¹⁸ cm^?3 are studied in the range of 85–300 K (and in some cases up to 700 K). The temperature dependences of electrical and thermal conductivity indicate that the low-temperature electron and phonon scattering initiated by the off-center impurity of sulfur exists. The temperature dependences of the electronic and lattice components of thermal conductivity are calculated in the approximation of a parabolic spectrum and electron scattering by acoustic phonons and neutral substitutional impurities. The lattice thermal conductivity is found to have a feature in the form of a shallow minimum in the range of 85–250 K. A similar feature, while not so clearly pronounced, is found to exist also in Pb_1?x Sn_xTe_1?x Se_x alloys (x≥0.15) with an off-center tin impurity. An analysis of the possible origins of this effect suggests that, at low temperatures, the Lorentz numbers L of the materials under study are smaller than the L₀ numbers employed which correspond to the above scattering mechanisms. The cause of the decrease in L is related to electron scattering at two-level systems, a mechanism whose effect grows with increasing electron energy. An analysis of experimental data obtained at high temperatures, as well as on undoped samples with the lowest possible carrier concentrations, yields the values of L for samples with different electron densities. The minimum value L/L₀ = 0.75 is obtained for a lightly doped sample at ～130 K.     

Performance of decorrelating receivers in multipath Rician fading channels

This letter focuses on the performance analysis of the decorrelating receiver in multipath Rician faded CDMA channels. M-ary QAM scheme is employed to improve the spectral efficiency. Approximate expressions are first derived for the two performance indexes: the average symbol error rate (SER) and the average bit error rate (BER) when the decorrelating-first receiver perfectly knows the channel information of the user of interest. To achieve desirable closed-form expressions of the SER and the BER, we exploit results in large system analysis and make assumptions of a high signal-to-interference ratio (SIR) and/or a small Rician K-factor. To measure the receiver performance in the practical scenario, we further derive expressions to approximate the average SER and BER of the decorrelating-first scheme with channel uncertainty. Simulation results demonstrate that the analytical results can also be employed to evaluate the performance of the combining-first receiver.     

Transient response of ARROW VCSELs under external optical feedback

The effect of external optical feedback on the transient response of antiresonant reflecting optical waveguide (ARROW) vertical-cavity surface-emitting lasers (VCSELs) is studied. It can be shown that the proper design of ARROW can suppress the excitation of high-order transverse leaky mode as well as increase the critical feedback strength so that stable high-power single-mode operation of VCSELs can be obtained even under the influence of strong external optical feedback.     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

小块气藏早期动态特征综合评价

应用试井方法，提出一套比较切合实际的小块气藏动态特征综合评价方法，推导出水驱气藏水侵量的计算公式，编制了天然气高压物性参数计算和气藏稳产年限预测等程序软件。     

阴,阳离子聚合物地层内凝胶化改善水驱效果的研究

研究了一杆阴离子聚合物（Ａｃ５３０）和一种阳离子聚合物（Ｍｂ５８１）在水溶液中形成凝胶的条件和过程、凝胶化学结构、形态、稳定性和力学性能。在模拟地层的二维微观模型内观测了两种聚合物驱替渗流、相逼、形成凝胶、凝胶封堵大孔道的机理。在亲水填砂模型内测定了阴、阳离子聚合物凝胶体系降低渗透率的能力。     

Effect of pulse time gate on CsI(T1) light output

The mass and charge identification of secondary particles with Z < 4 by a large CsI(T1) scintillation detector is performed using pulse shape analysis and time-of-flight methods. The dependence of the light output on E, A and Z is studied in the energy range of 1–20 MeV/A and special attention is paid to the integration time of the photomultiplier anode signal. It is found that the behaviour of the calibration curves strongly depends on the choice of the integration time interval.     

Modeling ion implantation of HgCdTe

Ion implantation of boron is used to create n on p photodiodes in vacancy-doped mercury cadmium telluride (MC.T). The junction is formed by Hg interstitials from the implant damage region diffusing into the MC.T and annihilating Hg vacancies. The resultant doping profile is n⁺/n^-/p, where the n⁺ region is near the surface and roughly coincides with the implant damage, the n^- region is where Hg vacancies have been annihilated revealing a residual grown-in donor, and the p region remains doped by Hg vacancy double acceptors. We have recently developed a new process modeling tool for simulating junction formation in MC.T by ion implantation. The interstitial source in the damage region is represented by stored interstitials whose distribution depends on the implant dose. These interstitials are released into the bulk at a constant, user defined rate. Once released, they diffuse away from the damage region and annihilate any Hg vacancies they encounter. In this paper, we present results of simulations using this tool and show how it can be used to quantitatively analyze the effects of variations in processing conditions, including implant dose, annealing temperature, and doping background.     

A hybrid spreading/despreading function with good SNR performancefor band-limited DS-CDMA

Code-division multiple-access (CDMA) implemented with direct-sequence spread spectrum (DS/SS) signaling is a promising multiplexing technique for cellular telecommunications services. The efficiency of a direct-sequence spread-spectrum code-division multiple-access (DS-CDMA) system depends heavily on the shape of the spectrum of the spread signal. Maximum efficiency is obtained with an ideal brick-wall bandpass spectrum. There are two approaches toward achieving such a spectrum. One is to use a simple spreader that produces a broad spectrum and then follow it with a precise, high order filter to band limit the spectrum. A second approach, which is the approach taken in this paper, is to use a spreader that produces a spectrum close to the ideal spectrum and then employ a simple filter to control the out-of-band power. The proposed spreader/despreader is based on a simple hybrid function and can be easily implemented. An analysis provides a compact expression for the signal-to-noise ratio (SNR) of a RAKE receiver. The expression includes the effects of baseband, intermediate frequency (IF) and RF filtering as well as the effects of the spectral densities of the spreading/despreading functions. The analysis shows that the proposed spreader/despreader yields superior performance over a conventional pseudo noise (PN) spreading/despreading mechanism