Results of an inter-laboratory comparison of methods for quantitative clay analysis

In a comparison of analytical methods in clay mineralogy, two clay samples (from Hennersdorf and Freydegg) of different clay composition were analyzed by 19 laboratories mainly by XRD. Participants used different methods of pre-treatment, preparation, analysis and evaluation.In spite of the diversity of analytical methods applied, reasonable conformity in quantitative results was obtained for the associated minerals (quartz, calcite and dolomite). On the other hand, qualitative identification of the clay minerals showed considerably stronger divergencies, causing a stronger deviation of quantitative data; analysis of the Freydegg sample proved to have been particularly difficult. The evaluation methods of the different participants were examined to determine whether similar methods provided results that could be more easily compared.In addition, the authors calculated the clay mineral composition according to three different recognized methods, using the same diffractograms and same preparation and measuring conditions. In spite of this, different results were obtained.In the next phase of the programme, an inter-laboratory comparison of methods will be achieved under exactly defined conditions of preparation and analysis.     

High-temperature gradient HPLC for the separation of polyethylene–polypropylene blends

A high-temperature gradient HPLC method has been developed for the analysis of polyethylene–polypropylene blends. For the first time it was possible to separate these polyolefin blends by a chromatographic technique which is operating at 140 °C. Blends of a commercial polypropylene and a medium molar mass linear polyethylene were separated using a mobile phase of ethylene glycol monobutylether (EGMBE) and 1,2,4-trichlorobenzene (TCB) and silica gel as the stationary phase. With the use of n-decanol as sample solvent, a precipitation–redissolution mechanism for polyethylene (PE) was established while polypropylene (PP) is eluted in size exclusion mode.     

Discovery of Riociguat (BAY 63‐2521): A Potent,Oral Stimulator of Soluble Guanylate Cyclase for the Treatment of Pulmonary Hypertension

Direct stimulation of soluble guanylate cyclase (sGC) represents a promising therapeutic strategy for the treatment of a range of diseases, including the severely disabling pulmonary hypertension (PH). Optimization of the unfavorable DMPK profile of previous sGC stimulators provided riociguat, which is currently being investigated in phase III clinical trials for the oral treatment of PH.

     

The effect of dielectric constant of materials on unipolar diffusion charging of nanoparticles

We investigated the dependence of unipolar diffusion charging of nanoparticles on the dielectric constant of the particle material experimentally. The examined nanoparticles (10–200 nm) cover a wide range of dielectric constant but have almost the same spherical or compact morphology. Measurements of both intrinsic charged fraction and mean charge per particle show very small differences among different materials. The level of the small difference is consistent with the estimation by Fuchs’ [(1963). On the stationary charge distribution on aerosol particles in bipolar ionic atmosphere. Geofisica Pura e Applicata, 56, 185–193] theory.     

Performance evaluation of three optical particle counters with an efficient “multimodal” calibration method

The sizing accuracies of two widely used yet hitherto unevaluated optical particle counters (OPCs—Grimm Model 1.109 and Palas Model WELAS 2100) as well as one high-resolution, non-commercial OPC were evaluated. The measured data were compared to scattering intensity calculations based on Mie theory. Additionally, the counting efficiency for all three counters was measured, as was the influence of coincidence effects for the OPC with the lowest (manufacturer specified) upper concentration limit.Beside the traditional polystyrene latex calibration, a little-known, very fast and precise “multimodal” calibration method was used, which is based on the simultaneous generation of up to eight sharp multiple-charge modes from polydisperse di-ethyl-hexyl-sebacate (DEHS) particles by electrical mobility classification.     

采用新型焊接电弧提高焊接生产的经济效益和焊缝质量

通过在传统的短路过渡电弧和射流过渡电弧的基础上进行创新,发展新型的焊接电弧,可以显著地提高电弧焊接在金属连接中的优越性。两种新的焊接电弧,forceArc~杂志焊接电弧和coldArc~焊接电弧可以在一个焊接电源上实现,对焊接生产具有现实意义。了解和掌握这些新型电弧的工艺特点,可以有效地将其应用到生产中,以此提高焊接产品的质量和焊接生产的经济效益。新型焊接电弧的出现使现有的有关焊前焊接接头准备的标准和规定,特别是有关坡口角度和焊接位置,需要重新考虑。新型焊接电弧可以应用于各种金属加工工业中的焊接生产,是对弧焊工艺的一个创新。     

An efficient method for solving the Signorini problem in the simulation of free-form surfaces produced by belt grinding

Industrial robots are recently introduced to the belt grinding of free-form surfaces to obtain high productive efficiency and constant surface quality. The simulation of belt grinding process can facilitate planning grinding paths and writing robotic programs before manufacturing. In simulation, it is crucial to get the force distribution in the contact area between the workpiece and the elastic contact wheel because the uneven distributed local forces are the main reason to the unequal local removals on the grated surface. The traditional way is to simplify this contact problem as a Signorini contact problem and use the finite element method (FEM) to calculate the force distribution. However, the FEM model is too computationally expensive to meet the real-time requirement. A new model based on support vector regression (SVR) technique is developed in this paper to calculate the force distribution instead of the FEM model. The new model approximates the FEM model with an error smaller than 5%, but executes much faster (1 s vs 15 min by FEM). With this new model, the real-time simulation and even the on-line robot control of grinding processes can be further conducted.