辅锅控制程序在CENTUM-CS上的实现

全面介绍辅锅点火系统，从硬件配置、安全条件、点火逻辑和软件组态等几个方面论述辅锅控制程序的原理及其在CENTUM—CS上的实现方法，对CS系统的进一步开发利用具有较大的启发和借鉴作用。     

挤出机头的热平衡分析及计算

建立了挤出机头的热开衡方程，并进行了分析和讨论。列出了方程中各个热通量计算公式，为挤出机头控制系统的设计提供了依据。     

几种增塑剂增塑聚乳酸的性能研究

用聚乙二醇（PEG）、邻苯二甲酸二辛酯（DOP）、柠檬酸三丁酯（TBC）、亚磷酸三苯酯（TPPi）、癸二酸二丁酯（DBS）分别与聚乳酸（PLA）熔融共混，通过试样拉伸性能测试和DSC分析，研究这几种增塑剂对PLA拉伸性能和热性能的作用。结果表明，在这几种增塑剂中，TPPi和DBS增塑效果最好，能显著降低PLA玻璃化转变温度和熔融温度，提高PLA断裂伸长率和结晶度。     

溴素法α-溴代间氯苯丙酮合成研究

在金属卤化物催化剂 HD2 0 0 1存在下 ,溴与间氯苯丙酮在乙酸中反应得到盐酸安非他酮中间体 α-溴代间氯苯丙酮。最佳反应条件是 :n(间氯苯丙酮 )∶n(溴 ) =1∶ 1 ,催化剂用量为 1 %(质量分数 ) ,溴滴加时间为 1 h,反应温度为 1 0°C,此条件下 ,产物纯度为 98.83%,收率为 96.1 %。     

氧化焰烧成铜红釉

本研究以SiC作还原剂，采用氧化焰烧成，试制成功了在1250～1260℃下烧成的铜红釉，克服了传统的还原焙烧成方法的不足，简化了生产工艺，提高了铜红釉的成品率。     

甲苯稀释对AlCl3-EMIC型离子液体电镀铝工艺氢脆性的影响

采用甲苯作为AlCl3-EMIC(1-乙基-3-甲基咪唑)型离子液体的稀释剂,其中纯态离子液体由物质的量比为2∶1的无水AlCl3和EMIC组成。对比了纯态和按稀释剂与离子液体体积比为1∶1稀释后电镀铝的外观、微观形貌和氢脆性。结果表明,采用甲苯稀释离子液体虽然可以降低镀液的黏度,改善镀层外观和微观形貌,但对离子液体电镀铝工艺的氢脆性有负面影响。     

聚丙烯塑料中二叔丁基过氧化物的测定

研究了在冰醋酸－盐酸介质中，以ＮａＩ作还原剂，Ｆｅ３＋作催化剂，测定二叔丁基过氧化物的条件，建立了在１００℃条件下催化碘量法测定二叔丁基过氧化物的新方法。该法用于聚丙烯塑料中微量过氧化物的测定，准确、可靠、方便。回收率为９８．７％，相对标准偏差为０．６４％。     

Studies of microhardness and mar resistance using a scanning probe microscope

Scanning probe microscopy (SPM) is in a period of rapid development. It shows great promise for characterizing coating surfaces. This paper describes modification of an SPM so that it can be used to mar the surfaces of coatings under controlled conditions and to characterize the mars. Mar resistance of coatings is analyzed in terms of a ‘three response, two mechanism model.' The three responses (fracture, elastic, and plastic) can be measured quantitatively using the SPM. Of the three responses, only two (fracture and plastic deformation) are marring mechanisms – elastic deformations recover instantaneously. In some cases mars resulting from plastic deformation may recover slowly with time or with immersion in water; this phenomenon is attributed to viscoelastic creep. Microhardness is also measured with the modified SPM. Some thermoset coatings appear to be substantially harder near their surfaces than in the mass of material, and such materials may respond quite differently to stress applied at different levels near the surface. This finding has important implications for all coating properties that are strongly influenced by the surface. A quantity called ‘micro mar resistance' is defined. It may be useful for comparing different coatings under specified conditions of marring. However, there can be no single quantity that expresses ‘mar resistance' of a coating under all conditions.     

MH对EBA阻燃及热降解行为影响

采用极限氧指数法、热重分析和差示扫描量热分析等技术和手段研究了氢氧化镁（MH）对乙烯-丙烯酸丁酯共聚物（EBA）的阻燃性能、力学性能及热降解行为的影响。结果表明：EBA／MH复合材料的拉伸强度、断裂伸长率和熔体流动速率均随着MH用量的增加而降低；当MH的质量分数为60％时，复合材料的极限氧指数可达34．3％；MH通过分解吸热可提高EBA的热稳定性；MH表面羟基与EBA的反应性基团发生相互作用，以及EBA发生酯裂解后形成的羧酸与MH反应形成热稳定性更高的离聚物，均可提高EBA在高温下的热稳定性，并改变EBA的热降解历程。MH的“热阱”机理对EBA的阻燃起着很重要的作用。     

Detecting video frame-rate up-conversion based on periodic properties of inter-frame similarity

Video frame-rate up-conversion is one of the common operations for tampering digital videos in the temporal domain, such as creating fake high-quality videos and splicing two video clips with different frame rates. However, few existing works have been proposed for detecting this form of tampering operation. Based on the analysis of extensive experiments, we found that frame-rate up-conversion algorithms employed in most current video editing softwares will inevitably introduce some periodic artifacts into inter-frame similarity in the resulting video frame sequence. By analyzing such artifacts, we propose a simple yet very effective method to expose video after frame-rate up-conversion, and further estimate its original frame rate. The experimental results evaluated on 100 original videos at different frame rates have shown the effectiveness of the proposed method. The average detection accuracy can achieve as high as 99 % on noise-free videos in uncompressed and H.264/AVC formats. Besides, the proposed method is robust to noise as the detection accuracy could reach over 85 % and 95 % on noised videos with Gaussian white noise when SNR is 33 db and 36 db respectively.