HDI工艺中取代涂树脂铜箔适合激光钻孔的半固化片

应用于HDI的激光钻孔半固化片的方法和其它常规材料相比具有的优缺点。     

基于粗糙集信息观的决策表属性约简方法

粗糙集理论是近年来发展起来的一种有效的处理不精确、不确定、含糊信息的数学理论方法，它被广泛应用于相容和不相容决策表的属性约简和核属性计算。利用反例指出目前基于粗糙集信息观[2、6]的决策表属性约简和核属性计算方法的局限性。对决策表的性质作了深入的研究，研究发现文献[2、6]方法的不足原因是：它们没有考虑U／ind（C）中等价类的相客性。给出了基于U／ind（C）中等价类相客性的属性约简定义和核属性定义，并给出了一种新的基于粗糙集信息观的决策表属性约简和核属性计算方法。讨论了该方法同文献[2、6]方法的区别。最后用相同实例验证了该方法的有效性。     

Flash器件中氧化硅/氮化硅/氧化硅的特性

对普遍采用的氧化硅/氮化硅/氧化硅( ONO)三层复合结构介质层的制备工艺及特性进行了研究分析,研究了ONO的漏电特性以及顶氧( top oxide)和底氧( bottom oxide)的厚度对ONO层漏电的影响.结果表明,采用较薄的底氧和较厚的顶氧,既能保证较高的临界电场强度,又能获得较薄的等效氧化层厚度,提高耦合率,降低编程电压.     

基于CB的串行口和接口板端口程序应用

串行口及接口板端口是计算机通信的主要途径 ,也是目前计算机工程测控中通用的基本方法。C Builder (简称CB)编程语言以其功能完备、开发效率高的特点而成为目前流行的程序开发工具 ,介绍了利用CB语言编写串行口和端口通信的程序的方法 ,并对具体的各方法编写了相应的示例。     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

计算高温高压条件下的钻井液当量循环密度

介绍了在高温高压的井眼条件下,温度和压力对钻井液当量循环密度的影响以及由此对井底压力影响的研究结果.高温会使井眼中的流体发生膨胀,而在深井中的高压则会压缩流体.如果没有考虑到这两种相反作用的影响,就会在计算井底压力时出现较大误差.温度和压力还会影响钻井液的流变性能.开发出一个称为DDSimulator的模拟程序,用于模拟循环条件下的井眼.用宾汉塑性模型来表征所研究的钻井液的流变特性,其流变参数与温度和压力呈函数关系.在DDSimulator模拟程序中使用了Crank-Nicolson数值离散图来绘制井眼温度分布曲线.模拟结果显示,地温梯度越高,井底压力越低;钻杆入口温度对井底温度和压力无显著影响;循环速度越高,井底温度越低、井底压力越高.     

用于磁场测量的高精度500A/30V零压开关直流稳流电源

研制了一种带有无源辅助网络的全桥移相脉宽调制零压开关(FB PSPWMZVS)高精度磁铁稳流电源,并在电磁铁磁场测量中得到应用,其电流稳定度在8h内优于±1×10-4。     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.