Optical, electrical and structural characteristics of Al:ZnO thin films with various thicknesses deposited by DC sputtering at room temperature and annealed in air or vacuum

Transparent and conductive Al-doped ZnO (AZO) films have been grown with various thicknesses between 0.3 and 1.1 μm by magnetron sputtering at room temperature onto soda lime glass substrates. After deposition, the samples have been annealed at temperatures ranging from 150 to 450 °C in air or vacuum. The optical, electrical, and structural characteristics of the AZO coatings have been analyzed as a function of the film thickness and the annealing parameters by spectrophotometry, Hall effect measurements, and X-ray diffraction. As-grown layers are found polycrystalline, with hexagonal structure that shows some elongation of the unit cells along the c-axis, having visible transmittance ∼85-90% and resistivity ∼1.6-2.0 mΩ cm, both parameters slightly decreasing when the film thickness increases. Heating in air or vacuum produces further elongation of the crystalline lattice together with some increase of the visible transmittance and a decrease of the electrical resistance that depends on the heating temperature and atmosphere. The best characteristics have been obtained after treatment in vacuum at 350 °C, where the highest carrier concentrations are achieved, giving visible transmittance ∼90-95% and resistivity ∼0.8-0.9 mΩ cm for the AZO layers with various thicknesses. Some relationships between the analyzed properties have been established, showing the dependence of the lattice distortion, the band gap energy and the mobility on the carrier concentration.     

Spectroelectrochemical sensing based on multimode selectivity simultaneously achievable in a single device. 9. Incorporation of planar waveguide technology

Incorporation of planar waveguide technology into a spectroelectrochemical sensor is described. In this sensor design, a potassium ion-exchanged BK7 glass waveguide was over-coated with a thin film of indium tin oxide (ITO) that served as an optically transparent electrode. A chemically selective film was spin-coated on top of the ITO film. The sensor supported five optical modes at 442 nm and three at 633 nm. Investigations on the impact of the ITO film on the optical properties of the waveguide and on the spectroelectrochemical performance of the sensor are reported. Sensing was based on the change in attenuation of light propagated through the waveguide resulting from an optically absorbing analyte. By applying either a triangular or square wave excitation potential waveform, electromodulation of the optical signal has been demonstrated with Fe(CN)6(3-/4-) as a model electroactive couple that partitions into a PDMDAAC-SiO2 film [where PDMDAAC = poly(dimethyldiallylammonium chloride)] and absorbs at 442 nm.     

Analysis of the drude model in metallic films

A method, believed to be new, to simulate Drude parameters for collective oscillation of the free carriers in metallic films is proposed. Plasma resonance frequency and relaxation were simulated simultaneously from both the real and the imaginary parts of the dielectric function of a metallic film after consideration of their correlation in the Drude model. As examples, the contributions of the electrons in Ag films and of the free carriers in metallic silicide, NbSi(2) and TaSi(2), films have been studied.     

Motorcyclist fatalities and the repeal of mandatory helmet wearing laws

Previous studies had estimated that repeal of mandatory helmet wearing laws resulted in increases in the number of fatalities ranging from nearly 40% to essentially zero. This study was performed to determine more definitively the influence on motorcyclist fatalities of these repeals. After repeal, motorcyclist fatalities increased more in the states which repealed their laws than in those which did not in 24 cases out of 26, with the 95% confidence interval for the average effect being 25 +/- 6%. It is therefore concluded that repeals of mandatory helmet wearing laws for motorcyclists were followed by substantial increases in motorcyclist fatalities.     

Influence of the copper ion on aging rate of oil-paper insulation in a power transformer

To identify the influence of copper ion on the aging rate of oil-paper insulation, accelerated thermal aging experiments on oil-paper insulation were designed and performed at two significant temperatures. A set of characteristic parameters, including dissolved gases, degree of polymerisation, furfural content, water content and acid number of oil, was tested. The experiments- results reveal that copper ion has a different influence on insulation paper and oil during the aging process of the insulation system. On the one hand, it delays the degradation of insulation paper, reducing the ratio of CO₂/CO by about 11% at 80%C and by more than 50% at 130%C. On the other hand, copper ion promotes the oxidation of oil and thus accelerates the aging rate.     

Advanced Code-Division Multiplexers for Superconducting Detector Arrays

Multiplexers based on the modulation of superconducting quantum interference devices are now regularly used in multi-kilopixel arrays of superconducting detectors for astrophysics, cosmology, and materials analysis. Over the next decade, much larger arrays will be needed. These larger arrays require new modulation techniques and compact multiplexer elements that fit within each pixel. We present a new in-focal-plane code-division multiplexer that provides multiplexing elements with the required scalability. This code-division multiplexer uses compact lithographic modulation elements that simultaneously multiplex both signal outputs and superconducting transition-edge sensor (TES) detector bias voltages. It eliminates the shunt resistor used to voltage bias TES detectors, greatly reduces power dissipation, allows different dc bias voltages for each TES, and makes all elements sufficiently compact to fit inside the detector pixel area. These in-focal plane code-division multiplexers can be combined with multi-GHz readout based on superconducting microresonators to scale to even larger arrays.     

Structural, chemical, and optical properties of tin sulfide thin films as controlled by the growth temperature during co-evaporation and subsequent annealing

Tin sulfide thin films on soda-lime glass substrate were prepared by co-evaporation. This technique uses a vapor phase procedure involving chemical reactions between the precursor species evaporated simultaneously. The influence of the substrate temperature in the crystal structure and chemical composition were determined by X-ray diffraction and energy dispersive analysis of X-rays, showing that thin films crystallized in SnS, SnS₂, and Sn₂S₃ phases. Scanning electron microscope shows thin films with homogenous and uniform surface. Some of the samples were annealed to study the variation of structural, chemical, and optical properties. The variation of refractive index (n), extinction coefficient (k), and dielectric constant (ε) with wavelength and photon energy are reported. The energy band gap was calculated from optical transmittance and reflectance measurements in the range 300–1500 nm. The calculated energy band gap values were between 1.75 and 2.3 eV, depending on the phase in which crystallized the different thin films.     

Evidence for plastic deformation in the natural polycrystalline diamond,framesite

Relief-polished striations have been found within grains in polished sections of framesite, a naturally occurring polycrystalline diamond. Because the narrow zones represented by these surface striations are harder than any orientation of the matrix (as revealed by abrasion resistance) and because they etch preferentially, they have been interpreted as representing oriented deformation bands within the grains. It is concluded that the microstructure of framesite is the result of plastic deformation of diamond grains probably under conditions such that brittle fracture was inhibited.     

Numerical approach to hopping conduction

A numerical method for calculation of the polarization conductivity has been developed. This approach has been applied to the correlated barrier hopping (CBH) and quantum mechanical tunnelling (QMT) models in the case of monoelectronic hops. These calculations have been performed on well-known solids such as carbon (HTT 600° C) and badly organized molybdenum and tungsten sulphides. The agreement between theory and experimental results is more satisfying than in a previous approach. The parametersW _M andN ₀ are determined for the CBH model, andN(E _F) for the QMT model.