Springback analysis of thin rectangular bars of non-linear work-hardening materials under torsional loading

A theoretical analysis of the springback of narrow rectangular strips of non-linear work-hardening material under torsional loading has been carried out. This theoretical analysis is supported by experimental results for rectangular mild steel strips of different thicknesses and lengths. Finally an analytical generalized expression relating angle of twist to twisting moment and residual angle of twist per unit length for rectangular strips under plastic torsion is obtained in non-dimensionalized form. A comparison between the results obtained for bars of non- linear and linear work-hardening materials loaded under torsion is also made.     

Laminar-turbulent transition behavior of fully developed air flow in a heated horizontal tube

I have experimentally studied the influence of the buoyancy force and inlet flow conditions on the laminar-turbulent transition process of fully developed air flow in a heated horizontal tube with uniform wall heat flux at modified Rayleigh number 3.1×10⁶. Eight time-series of the air temperature were simultaneously obtained using eight thermocouples positioned within the tube along a vertical line passing through the tube's axis. I have studied the time and space dependence of the transition behavior by analyzing these instantaneous time-series. By calculating a set of Lyapunov exponents and the correlation dimension of the time-series of a single thermocouple, these transitional flows are found to be chaotic.     

The onset of vortex instability in laminar forced convection flow through a horizontal porous channel

The onset of convective instability in a fluid-saturated porous layer between the two horizontal plates heated isothermally from below has been analyzed theoretically by using propagation theory. In the analysis the thermal dispersion coefficient is assumed to be proportional to the streamwise velocity. The results show that both inertia and thermal dispersion stabilize the system.     

FLOCCULATION OF ASPHALTENES AT HIGH PRESSURE. II. CALCULATION OF THE ONSET OF FLOCCULATION

The influence of pressure on the onset of flocculation of asphaltenes was calculated in the region from 1 to 300 bar and from 50 to 100°C. These calculations are the counterpart to our experimental data which, recently, have been reported in part 1 of an equally titled article [9]. As gas component methane and as precipitant i-octane were used. The asphaltene flocculation was considered to be a liquid-liquid equilibrium. For modelling the van der Waals equation of state (vdW-EOS) in the framework of continuous thermodynamics was applied. The composition of the crude oil was described by a continuous distribution function with respect to the solubility parameter δ of the Scatchard-Hildebrand theory. Within the distribution the asphaltenes represent the species with the highest δ-values. For oils with a very low content of asphaltenes the model developed describes the experimental flocculation data reasonably. In accordance to the experimental data the model predicts that, in the considered pressure range, without addition of i-octane asphaltene flocculation does not occur. However, on contrary to the experimental results, the model predicts the asphaltenes to show a higher flocculation tendency with increasing asphaltene content of the crude oil. For very high asphaltene contents the model even completely fails. Probably, the reason of this lack is the disregarding of asphaltene association.     

Properties of Carbopol Solutions as Models for Yield-Stress Fluids

ABSTRACT: The effect of pH on the non-Newtonian viscosity (η)of aqueous Carbopol 940 solutions is presented with high resolution (pH increments about 0.4) between pH = 2.8 and 12.7. Aqueous NaOH was used to adjust pH of 1.48 wt % Carbopol solutions. A Contraves viscometer was used to measure steady-flow shear stress at known shear rate (γ) over the range γ= 8 to 195 s⁻¹. Yield stresses and shear-thinning η(γ) were observed. Data were fitted with a Herschel-Bulkley model, whose parameters (including yield stress) were expressed as functions of pH. Comparisons were made of η(γ) to the dynamic viscometric properties η'(ω) and η*(ω) for comparable ranges of γ and frequency (ω): A fairly close match was found between η and η* but η«η'. pH dependence included previously unreported extrema of h(pH) in the range of pH = 6.2 to 6.6. Because of sensitive control of rheological properties with pH, Carbopol solutions can be used to mimic a great range of shear-thinning and yield-stress behavior that should make them useful for model studies directed toward process and equipment design and evaluation.     

TMAOase Activity of European Hake (Merluccius merluccius) Organs: Influence of Biological Condition and Season

ABSTRACT: Trimethylamine N-oxide demethylase (TMAOase) activity of several internal organs of hake were studied for 2 consecutive y. The correlation between enzymatic activity and season of year, sex, weight, and length were analyzed. While kidney and spleen showed the highest activities, liver, heart, bile, and gall bladder activities were much lower, and in some cases they were below the detection limit. A correlation between TMAOase activity of kidney and season was found. During winter and spring (February to May), the months matching the spawning peak, high activities were detected, while in summer months the activity level was lower. TMAOase activity in the rest of the organs did not seem to have a seasonal influence. Keywords: TMAOase, season, biological condition, hake, soluble protein     

Vestigial sideband filtering at 10 Gbit/s using 12.5 GHzchannel-spacing demux

A 32-channel 12.5 GHz-spaced free-space demux with low crosstalk and low polarisation dependent loss has been constructed. Using this demux, vestigial sideband filtering at 10 Gbit/s has been studied. It is shown that this demux can achieve very high spectral efficiency without polarisation division multiplexing     

Intermetallic compounds formed at the interface between liquid indium and copper substrates

The interfacial reactions between liquid In and Cu substrates at temperatures ranging from 175°C to 400°C are investigated for the applications in bonding recycled sputtering targets to their backing plates. Experimental results show that a scallop-shaped Cu₁₆In₉ intermetallic compound is found at the Cu/In interface after solder reactions at temperatures above 300°C. A double-layer structure of intermetallic compounds containing scallop-shaped Cu₁₁In₉ and continuous CuIn is observed after the Cu/In interfacial reaction at temperatures below 300°C. The growth of all these intermetallic compounds follows the parabolic law, which implies that the growth is diffusion-controlled. The activation energies for the growth of Cu₁₆In₉, Cu₁₁In₉, and CuIn intermetallic compounds calculated from the Arrhenius plot of growth reaction constants are 59.5, 16.9, and 23.5 kJ/mole, respectively.