Effect of grain boundaries on isothermal solidification during transient liquid phase brazing

The influence of liquid penetration at grain boundary regions on the rate of advance of the solid-liquid interface during isothermal solidification of transient liquid phase (TLP) brazed nickel joints has been examined. The test samples used in this study were Ohno-cast nickel with a grain size of >4 mm and a fine-grained nickel with a grain size of around 40 μm. Both Ni-base materials had the same chemical composition. The rate of isothermal solidification was greater when fine-grained nickel was employed during TLP brazing using Ni-11 wt pct P filler metal at 1200 °C. Liquid penetration at grain boundaries accelerates the isothermal solidification process by increasing the effective solid-liquid interfacial area and increasing the rate of solute diffusion into the base material. An analysis of electron channeling patterns has confirmed that random high-angle boundaries have a greater influence on the rate of isothermal solidification than ordered boundaries including small-angle or twin boundaries. Formerly Visiting Scientist, Department of Metallurgy and Materials Science, University of Toronto. Formerly Postdoctoral Fellow, Department of Metallurgy and Materials Science, University of Toronto     

Nanolayered lightweight flexible shields with multidirectional optical transparency

New nanolayered coatings are designed and deposited on flexible plastic substrate having the thickness of 100 /spl mu/m, in order to realize lightweight ultrathin transparent shielding foils. The structure of the coating is optimized considering three figures of merit: the average transmittance in the visible range for normal incidence, the normalized average transmittance for oblique incidence at 550 nm, and the transmittance quality factor. The nanotechnology exploited for the deposition of the transparent metals is the dual ion beam sputtering. Tests of durability, optical transmission, and shielding effectiveness demonstrate that the film has a high adhesion under mechanical solicitation, high resistance against aging, peak transmittance in the visible range higher than 70%, omnidirectional properties in the range 0/spl deg/-60/spl deg/, and shielding effectiveness of 40 dB up to 6 GHz.     

Evaluating the application of a decision support system in identifying adequate wastewater treatment for small communities. A case study: the Fluvia River Basin.

The identification of adequate wastewater treatment for small communities is a complex problem since it demands a combination of data from different sources, such as aspects of the community and landscape, the receiving environment and the available wastewater treatment technologies. The Catalan Water Agency (Agència Catalana de l'Aigua) considered using an EDSS (Environmental Decision Support System) as a tool to help water managers select the most adequate treatment for the urban wastewater of nearly 3,500 small communities in Catalonia (Spain). From that moment, EDSS was applied to all the river basins in Catalonia. In this paper the authors present the results obtained for the 76 small communities located in one of these river basins: the Fluvia River Basin. The characteristics of the community used in the reasoning process of the EDSS, the list of selected wastewater treatment alternatives, the technical environmental justification for the selected treatments and the reasons for discarding, favouring or disadvantaging them are presented. Finally, some results for the Fluvia River Basin are compared with those obtained in other Catalan river basins with different characteristics in order to evaluate which are the significant features in identifying adequate wastewater treatments.     

Hydrologic regionalisation impacts on wet-weather control selection.

Continuous simulation is performed using the US Environmental Protection Agency (USEPA) Storm Water Management Model (SWMM) to evaluate regional differences around the United States in hydrologic and water quality performance of wet-weather controls. Controls are characterised as being limited by peak inflow rate (i.e. any device with little or no storage, such as screens, filters and some proprietary devices) or by storage capacity (e.g., ponds, tanks). For flow-limited devices, results are presented in the form of percentage of annual runoff volume captured (passing through the device) for a given inflow capacity. For storage-limited devices, results are presented in two forms: percentage of annual runoff volume captured as a function of unit basin size and drawdown (drain) time, and as a percentage of total suspended solids captured, for the same two variables. Regional differences are apparent, driven mainly by variations in rainfall patterns around the country.     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure     

Determination of precompression and compression force levels to minimize tablet friability using simplex

Pilot simplex experiments for improving the tablet strength of three aspirin tablet formulations based on precompression and compression forces were presented. As each simplex moved towards the direction of the optimum, the friability was being minimized and the crushing strength was concomittantly being maximized. Because it followed a systematic direction, simplex process would locate a local optimum rapidly. The appropriate levels of precompression and compression forces that produced tablets with the desired strength were attained in five trials. By contrast, random search for this force combination required at least ten trials. Simplex technique is a cost and time effective means for determining the precompression and compression forces that will reduce the friability or increase the hardness of a tablet formulation. Results appeared to also indicate that crushing strength might be a more reliable measure of tablet strength than friability.     

Experimental abatement data of underflow baffles for removal of floatables in the CSOs of the Greater Montréal (Canada) area.

Underflow baffles have gained in popularity over the years as a viable mean to intercept floatables in Combined Sewer Overflows (CSOs). This choice was mainly justified by the extremely low capital cost (CAPEX) and operational cost (OPEX) of this solution, although the efficiency of underflow baffles has never been clearly proven. The only similar application to underflow baffles are scum boards in grit chambers and clarifier. However, the flow conditions at CSOs vary considerably from those in grit chambers and clarifier. For this reason, review of the behavior of floatables in a rapid flow is paramount. Only then can comprehensive design criteria for underflow baffles and overflow chambers be suggested. Pilot scale tests, performed in a 17 metres long basin at various flowrates, had already shown that a critical horizontal velocity for floatables (Vcr) may develop in the overflow chambers. In this follow up study, the fate of intercepted floatables was investigated. It appears from this latest data that permanent capture of floatables decreases rapidly with an increase in the horizontal velocity of the flow, no matter what the baffle depth. Baffle depth increases capture at lower velocities (0.17 m/s) but become irrelevant at higher velocities (0.61 m/s). This data suggests that capture efficiency of existing underflow baffles in overflow chambers can be, at best, very low whenever the horizontal velocity increases above 0.30 m/s or 1 ft/s.     

Indoor body-area channel model for narrowband communications

Using wireless sensors placed on a person to continuously monitor health information is a promising new application. At the same time, new low-power wireless standards such as Bluetooth and Zigbee have been proposed for short range, low data-rate communication matching the requirements of these bio-medical applications. However, there are currently few measurements or models describing propagation around the body. To address this problem, electromagnetic waves near the torso are measured and a statistical model is derived for communication in the 915 MHz and 2.45 GHz industrial, scientific and medical bands associated with Zigbee and Bluetooth. Measurement setup and statistical analysis are described.     

Finite element analysis of helicoidal waveguides

The purpose of the paper is to propose an efficient method to compute propagation modes in helicoidal waveguides. An helicoidal system of co-ordinates is introduced to define the structure and to set up the problem. These co-ordinates, albeit non-orthogonal, preserve the translational invariance in a way that allows a two-dimensional finite element model similar to that of classical straight waveguides