Switched-Current Filters Revisited: Square-Root Domain Sampled-Data Filters

In this brief, the well-known switched-current (SI) filtering technique is revisited using the concept of the square-root domain (SRD) filtering. It is proved that SI filters are a subclass of the SRD filters, where sampled-data signal processing is performed. This is achieved by considering typical lossless and lossy SRD sampled-data integrator configurations, using a set of complementary SRD operators which are based on the quadratic I-V relationship of MOS transistor operated in the saturation. Circuit examples are given, where linear-domain integrator and third-order filter configurations were derived using appropriate SRD sampled-data building blocks     

Finding structure in audio for music information retrieval

This paper presents a brief overview of recent approaches to two problems in music information retrieval: query by example and automated source separation. It describes the challenges inherent in musical query by example and the systems that take very different approaches to the problem. The paper also explores approaches to source separation in a musical context, focusing on systems that take distinct approaches to the problem. Finally, it comments about the future directions for digital signal processing (DSP) research in the context of music information retrieval.     

基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

Parametric effects on the transient Voltage performance of a DC superconducting cable

The objective of this work was to determine the significant parameters of a 3-GW 200-kV dc superconducting cable system which influence the transient voltage distribution in the various parts of the cable. The cable system consists of four coaxial metallic cylinders. It was found that the dielectric constant and the electrical resistivity of the soil significantly affect the severity of the transient voltages; lower dielectric constant and higher resistivity of the soil will increase the magnitudes of the transient voltages by increasing the earth-return impedance. It was also found that the effect of the conductor internal impedances of the cable is insignificant. Shorting the coaxial cylinders of the cryogen flow and the cryostat will lessen the severity of the transient voltages. Grounding the second, third, and fourth cylinders at regular intervals with low-impedance grounding impedance will also improve the transient performance of the cable. More research is needed to evaluate these procedures.     

Nonlinear crack dynamics and scaling aspects of fracture (experimental and theoretical study)

Nonlinear dynamics of crack propagation are investigated experimentally and theoretically with the goal of clarifying the nature of limiting crack velocity, the transition from steady state to branching regimes of crack dynamics, and the dynamics of crack arrest. The theoretical explanation of limiting steady-state crack velocity and the transition to a branching regime was proposed due to the study of collective behavior of a microcrack ensemble at the crack tip area. The experimental study of crack dynamics was carried out in a preloaded plate PMMA specimen using the high-speed camera coupled with the photo-elasticity method, the point stress recording with a laser system, and the failure surface roughness measurement.     

EBSP study of the annealing behavior of aluminum deformed by equal channel angular processing

Commercial purity aluminum (99.5%) was fabricated by equal channel angular pressing (ECAP) up to total accumulated strains of approx. 10. The annealing behavior of material deformed to total strains of approx. 1 and 10 was investigated, using heat treatments of 2 h at various temperatures from 100 to 500 °C. The microstructure of the annealed materials was characterized using the electron back-scatter pattern technique. A number of parameters were determined including the distribution and average values of both the boundary spacings and misorientations. For samples deformed to a total strain of 1, annealing resulted in discontinuous recrystallization. For samples deformed to a total strain of 10, annealing resulted in microstructures exhibiting characteristics of both uniform coarsening and, in a number of places, of discontinuous recrystallization. An attempt was made, based on the boundary spacing distributions, to separate these two components. The grain size after annealing was still however small, being just 6.4 μm after 2 h at 300 °C.     

Fracture response of fibre-reinforced materials with macro/microcrack damage using the Boundary Element Technique

The Boundary Element Method (BEM) incorporating the Embedded Cell Approach (ECA) has been used to analyse the effects of constituent material properties, fibre spatial distribution and microcrack damage on the localised behaviour of transversely fractured, unidirectional fibre-reinforced composites. Three specific composites, i.e., glass fibre reinforced polyester, carbon fibre reinforced epoxy and a glass-carbon hybrid, are considered. The geometrical structures examined were perfectly periodic, uniformly spaced fibre arrangements in square and hexagonal embedded cells. In addition, numerical simulations were also conducted using embedded cells containing randomly distributed fibres. The models involve both elastic fibres and matrix, with the interfaces between the different phases being fully bonded. The results indicate that the constituent material properties (two phase composite) and spatial distribution have a significant effect on the localised stress distributions around the primary crack tip. However, the strain energy release rate associated with crack propagation is predominantly influenced by the material composition. The three-phase hybrid composite exhibited an apparent intermediate fracture toughness value, compared to the all-glass and all-carbon models. Furthermore, the strain energy release rate for the macrocrack lowers as it enters a zone of localised damage (microcracking). The presence of microcracks relaxes the stress field, which can result in a significant reduction in the energetics of the primary crack.     

农村通信如何"突围"

农村通信作为农村地区信息化的基础，对于全面建设小康具有特殊的重要地位。介绍了我国农村通信的发展现状，分析了农村通信发展的困难压其原因，最后对农村压边远、欠发达地区通信的均衡震展提出了一些建议。     

Fabrication, assembly, and characterization of molecular electronic components

One of the ultimate miniaturizations in nanotechnology is molecular electronics, where devices will consist of individual molecules. There are many complications associated with the use of molecules in electronic devices, such as the electronic perturbations in the molecule associated with being bonded to an electrode, how electrons traverse the metal-molecule junction, and the difficulty of macroscopically addressing single to very few molecules. Whether fabricating a test structure or a usable device, the use of self-assembly is fundamental to the fabrication of molecular electronic devices. We will discuss how to fabricate self-assembled monolayers into test assemblies and how to use intermolecular interactions to direct molecules into desired positions to create nanostructures and to connect functional molecules to the outside world. These assemblies serve as test structures for measurements on single or bundled molecules. The development of several experimental techniques, including various scanning probes, mercury drop junctions, break junctions, nanopores, crossed wires, and other techniques using nanoparticles have enabled the ability to test these structures and make reproducible measurements on single molecules. Many of these methods have been developed to test molecules with potential for integration into devices such as oligo (phenylene-ethynylene) molecules and other /spl pi/-conjugated molecules, in ensemble or single-molecule measurements.