Optimized partitioning of a wavelength distributed data interfacering network

A fiber optic ring network, such as fiber distributed data interface (FDDI), can be operated over multiple wavelengths on its existing fiber plant consisting of point-to-point fiber links. Using wavelength division multiplexing (WDM) technology, FDDI nodes can be partitioned to operate over multiple subnetworks, with each subnetwork operating independently on a different wavelength, and inter-subnetwork traffic forwarding performed by a bridge. For this multiwavelength version of FDDI, which we refer to as wavelength distributed data interface (WDDI), we examine the necessary upgrades to the architecture of a FDDI node, including its possibility to serve as a bridge. The main motivation behind this study is that, as network traffic scales beyond (the single-wavelength) FDDI's information-carrying capacity, its multiwavelength version, WDDI, can gracefully accommodate such traffic growth. A number of design choices exist in constructing a good WDDI network. Specifically, we investigate algorithms using which, based on prevailing traffic conditions, partitioning of nodes into subnetworks can be performed in an optimized fashion. Our algorithms partition the nodes into subrings, such that the total traffic flow in the network and/or the network-wide average packet delay is minimized     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Afterburner [network-independent card for protocols]

Many current implementations of protocols such as the Transmission Control Protocol/Internet Protocol (TCP/IP) are inefficient because data are often accessed more frequently than necessary. Three techniques that reduce the need for memory bandwidth are proposed. The techniques are copy-on-write, page remapping, and single-copy. Afterburner, a network-independent card that provides the services that are necessary for a single-copy protocol stack, is described. The card has 1 MByte of local buffers and provides a simple interface to a variety of network link adapters, including HIPPI and asynchronous transfer mode (ATM). Afterburner can support transfers to and from the link adapter card at rates up to 1 Gbit/s. An implementation of TCP/IP that uses the features provided by Afterburner to reduce the movement of data to a single copy is discussed. Measurements of the end-to-end performance of Afterburner and the single-copy implementation of TCP/IP are presented     

A systematic techno-economic assessment of a WEC system installation for low-cost electrification of a habitable dwelling

This paper deals with the technical feasibility and economic viability of a grid connected wind-energy conversion system (WECS) used to cover the energy demand of an average habitable dwelling. The various parts of the wind-energy system are described and the useful electrical energy production is determined using a simulation program based on the Monte Carlo method. An economic analysis of the WEC system is performed using a computerized assessment tool. Important financial indices are calculated and financial scenarios investigated.     

The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Security issues for downloaded code in mobile phones

'Software defined radio' (SDR) is a technology that will appear in future generations of mobile phones, i.e. following the third-generation mobile phone technology that is currently being defined and developed. Early versions of 'pragmatic' SDR will allow the terminal to be reconfigured at any level of its protocol stack. Ultimately, the 'pure' SDR technology will allow a mobile phone or terminal to have its air interface software configured or reconfigured by other software (or software parameters) that have been downloaded to the terminal, e.g. over the air, or from a remote server via the Internet and one's personal computer (PC). A number of security issues arise with downloaded code that implements the air interface functions, and these may not be obvious simply from looking at the way PC software is updated on-line today. This paper starts with an outline of the code that allows a mobile phone to operate over a particular air interface. This sets the baseline for a discussion of the security issues surrounding the change of this code from one that is fixed and downloaded once only, to code that is reconfigurable during the life of a product.