Intrinsic scattering and absorption losses of Ge- and F-doped optical fibres prepared by PCVD

The scattering absorption and profile losses of PCVD fibres are analysed. The Rayleigh scattering increases proportionally to the sum of the F- and Ge-dopant concentrations, the UV absorption is proportional to the Ge concentration, and profiling losses are negligible.<>     

Description of the Inter-laboratory Comparison Programme in the New Zealand dairy industry

The Inter-laboratory Comparison Programme (ILCP) is a quality assurance system administered by the Dairy Division of the Ministry of Agriculture and Fisheries to monitor the performance of agency certified laboratories (ACLs). The programme works on a monthly basis during the milk producing season and is co-ordinated from the National Dairy Laboratory (NDL). Samples are despatched to Regional Dairy Labora-tories (RDL) and to the ACLs 2 weeks later. The RDL results are used to calculate an official mean. The ACL results are sent to the RDL where they are scrutinized immediately; hence, a rapid feedback on the ACL performance is possible. The NDL despatches a detailed statistical evaluation of results of ACLs and RDLs. The pro-gramme has increased from seven products in 1977 to eleven in 1984. Microbiological and chemical analyses are performed. A bacterial identification scheme to monitor E. coli and S. aureus was included in 1982. A scoring system (0 poor-10 good) which includes a weighting for specific tests and which is measured against an 'official' score has been introduced into a report which is distributed to all participants. The data generated by the programme are used by both ACLs and RDLs to check their analytical performance and quality control. Data are used by Dairy Division, as a national compilation of results issued by it which serves to highlight problem analyses, season trends and analytical limits.     

Characterization of indoor air pollution

This is a review paper addressing the current state-of-the-art. Concerns that motivate studies of the indoor environment are reviewed in the introduction. The source and typical diurnal variations of the concentration of several air contaminants are discussed in the section on characterization. A dynamic model is described in the section on indoor air quality modeling. Indoor air pollution control techniques are addressed in the last section.     

NEIGHBORHOOD APPROACHES TO URBAN CAPACITY BUILDING

The authors argue that the solution of urban problems requires resources and powers far beyond those available to most local governments. Only through partnerships of all relevant actors—public officials, businessmen and neighborhood residents—can such issues be dealt with. Yet, partnerships are neither simple nor inevitable. They require hard work and usually the development of the capacities of all involved. Such capacity building for partnerships is on three levels: the development of the individual capacity to play partnership roles; the creation of interactive partnerships operating as local problem solvers; and the fostering of inter-partnership networks. Neighborhoods are seen as the building blocks of cities, serving as a locality of scale upon which the citizen can base his concerns and actions and within which partnerships can operate effectively. Specific recommendations are made, utilizing this policy context to build capacity for partnerships at the neighborhood level, particularly with regard to the Intergovernmental Personnel Act.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

Long-term recovery of pressurized water reactors following a large break loss-of-coolant accident

The U.S. Nuclear Regulatory Commission recently identified a possible safety concern for pressurized water reactors. Following the reflood phase of a large break loss-of-coolant accident, long-term cooling of the reactor core may not be ensured. Specifically, the concern is that, for a pump discharge cold leg break, the loop seals in the reactor coolant pump suction piping will refill with liquid and the post-reflood steam production may depress the liquid levels in the downflow sides of the loop seals. A loop seal depression would cause a corresponding depression of the core liquid levels and possibly a fuel rod heatup in the upper core region. This paper is intended as an introduction of the safety issue that: (1) describes the important aspects of the problem, (2) provides an initial analysis of the consequences, and (3) discusses ongoing work in this area. Because the elevation of the loop seals is near the mid-core elevation in plants of Westinghouse design, the concern is greatest for those plants. There is less concern for most plants of Combustion Engineering design, and likely no concern for plants of Babcock and Wilcox design. This issue was addressed by employing both steady-state and transient systems analysis approaches. Two approaches were used because of uncertainties regarding actual reactor coolant system behavior during the post-reflood period. The steady-state approach involved the development and application of a simple computer program to investigate reactor coolant system behavior assuming quiescent post-reflood conditions. The transient systems approach involved investigating this behavior using the RELAP5/MOD2 computer code and a comprehensive RELAP5 model of a Westinghouse pressurized water reactor. The steady-state analysis indicated only a moderate fuel rod heatup is possible. The transient systems analysis indicated boiling and condensation-induced flow oscillations are sufficient to prevent fuel rod heatup. Analysis uncertainties are discussed.     

Design for a high power-density Astron reactor

A liquid lithium blanket surrounding the plasma volume is described. The liquid lithium flows along magnetic flux tubes at a high speed. There is no vacuum wall between the blanket and the plasma. The E-layer of relativistic particles within which the plasma is confined serves as a vacuum wall protecting the plasma from the lithium vapor, which is continuously produced at the surface of the blanket, by ionizing the lithium atoms and ejecting the same along open magnetic lines. The heat load at the surface of the blanket generated by 14 MeV neutrons can be several hundred MW per square meter.Work performed under the auspices of the U.S. Atomic Energy Commission.Deceased September 24, 1972.