Data sharing mechanism of various mineral resources based on blockchain

Basins with various mineral resources coexisting and enriching often occupy an important strategic position. The exploration of various mineral resources is repetitive at present due to unshared data and imperfect management mechanism. This situation greatly increases the cost of energy exploitation in the country. Traditional data-sharing mode has several disadvantages, such as high cost, difficulty in confirming the right of data, and lack of incentive mechanism, which make achieving real data sharing difficult. In this paper, we propose a data-sharing mechanism based on blockchain and provide implementation suggestions and technical key points. Compared with traditional data-sharing methods, the proposed data-sharing mechanism can realize data sharing, ensure data quality, and protect intellectual property. Moreover, key points in the construction are stated in the case study section to verify the feasibility of the data-sharing system based on blockchain proposed in this paper.     

信永中和"登云股份IPO审计失败"探究

本文以证监会发布的针对信永中和及两名签字注册会计师的行政处罚决定书为切入点,结合深圳证券交易所、天眼查、巨潮资讯等网站公布的相关信息,从信永中和的具体审计过程,分析登云股份IPO审计失败的原因,原因主要在于基于业务需要未充分了解公司及其经营环境,贸然接受委托,缺乏应有的执业审慎,缺少了必要的审计程序,复核制度流于形式丧失了发现错误的最后机会。     

基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

0Cr20Mn21Ni2N奥氏体不锈钢锻件组织性能研究

研究了无磁钻铤用0Cr20Mn21Ni2N奥氏体不锈钢圆棒锻件横截面的室温强度、硬度和韧性等力学性能,并从微观角度进行了分析。在圆棒表层区域观察到了锻造变形态晶粒组织,而直径四分之一区域为再结晶组织,平均晶粒尺寸为80μm,芯部再结晶晶粒尺寸粗化为150μm,这些差异是由不同的变形温度和降温速度造成的。这种组织差异导致的室温拉伸性能和冲击韧性也有相应的变化趋势。研究结果表明,在900、1000℃以0.5 s-1的应变速率压缩的0Cr20Mn21Ni2N试验钢样品,其应力应变曲线具有一定的加工硬化特征,其芯部硬度比应变速率为0.1 s-1的样品分别提升了28、15 HB。在700、800℃以20%以上的变形量进行压缩时,峰值抗力显著提高,而在900、1000℃以10%~50%的变形量进行压缩时,峰值抗力均无明显提高,可保证顺利的变形过程。     

面源红外诱饵对抗红外制导导弹干扰策略研究

面源红外诱饵使用的过程中,合理有效的干扰策略是干扰红外制导导弹的关键,针对这一问题,通过理论分析与仿真模拟相结合得到面源红外诱饵对抗红外制导导弹的干扰策略。首先以红外成像制导导弹为例,介绍红外制导导弹的仿真模型,然后将攻击过程分为锁定前与锁定后,以命中率为评价指标,得到两个阶段下的最佳干扰策略,包括诱饵的最佳释放时机、释放间隔以及载机应采取的机动动作等。     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

醇解技术在制备皮革加脂剂方面的研究进展

本文介绍了醇解反应的动力学、影响醇解反应收率的因素以及醇解反应在合成加脂剂方面的应用。     

Blind estimation of OFDM carrier frequency offset via oversampling

Blind deterministic estimation of the orthogonal frequency division multiplexing (OFDM) frequency offset via oversampling is proposed in this paper. This method utilizes the intrinsic phase shift of neighboring sample points incurred by the frequency offset that is common among all subcarriers. The proposed method is data efficient - it requires only a single OFDM symbol to achieve reliable estimation, hence making it more suitable to systems with stringent delay requirement and mobility-induced channel variation. The proposed scheme is devised to perfectly retrieve frequency offset in the absence of noise. Quite remarkably, we show that in the presence of channel noise, this intuitive scheme is indeed the maximum likelihood estimate of the carrier frequency offset. The possible presence of virtual carriers are also accommodated in the system model, and some interesting observations are obtained. The Cramer-Rao lower bound is derived for the oversampling-based signal model, and we show through numerical simulation that the proposed algorithm is efficient. Practical issues such as identifiability, the front-end filter bandwidth, and the possible presence of correlated noises are also carefully addressed.     

光缆接续损耗的工程控制

本从影响光纤损耗的主要因素分析着手，提出了光缆接续损耗工程控制的简洁有效的方法。     

复合流场上吸罩流场理论分析

提出在计算复合流场内存在两种不同流态的流动:势流和紊流。针对两种流动,分别建立了其数学模型,对于紊流流场,针对标准k-ε紊流模型的缺陷,采用了RNGk-ε紊流模型使紊流控制方程封闭。以及提出了边界条件的确定原则。为复合流场的数值计算提供了理论指导。