A distributed energy system integrating SOFC-MGT with mid-and-low temperature solar thermochemical hydrogen fuel production

Solar thermochemical hydrogen production with energy level upgraded from solar thermal to chemical energy shows great potential. By integrating mid-and-low temperature solar thermochemistry and solid oxide fuel cells, in this paper, a new distributed energy system combining power, cooling, and heating is proposed and analyzed from thermodynamic, energy and exergy viewpoints. Different from the high temperature solar thermochemistry (above 1073.15 K), the mid-and-low temperature solar thermochemistry utilizes concentrated solar thermal (473.15–573.15 K) to drive methanol decomposition reaction, reducing irreversible heat collection loss. The produced hydrogen-rich fuel is converted into power through solid oxide fuel cells and micro gas turbines successively, realizing the cascaded utilization of fuel and solar energy. Numerical simulation is conducted to investigate the system thermodynamic performances under design and off-design conditions. Promising results reveal that solar-to-hydrogen and net solar-to-electricity efficiencies reach 66.26% and 40.93%, respectively. With the solar thermochemical conversion and hydrogen-rich fuel cascade utilization, the system exergy and overall energy efficiencies reach 59.76% and 80.74%, respectively. This research may provide a pathway for efficient hydrogen-rich fuel production and power generation.     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

0Cr20Mn21Ni2N奥氏体不锈钢锻件组织性能研究

研究了无磁钻铤用0Cr20Mn21Ni2N奥氏体不锈钢圆棒锻件横截面的室温强度、硬度和韧性等力学性能,并从微观角度进行了分析。在圆棒表层区域观察到了锻造变形态晶粒组织,而直径四分之一区域为再结晶组织,平均晶粒尺寸为80μm,芯部再结晶晶粒尺寸粗化为150μm,这些差异是由不同的变形温度和降温速度造成的。这种组织差异导致的室温拉伸性能和冲击韧性也有相应的变化趋势。研究结果表明,在900、1000℃以0.5 s-1的应变速率压缩的0Cr20Mn21Ni2N试验钢样品,其应力应变曲线具有一定的加工硬化特征,其芯部硬度比应变速率为0.1 s-1的样品分别提升了28、15 HB。在700、800℃以20%以上的变形量进行压缩时,峰值抗力显著提高,而在900、1000℃以10%~50%的变形量进行压缩时,峰值抗力均无明显提高,可保证顺利的变形过程。     

马钢张庄矿高压辊磨机装配工艺研究

针对马钢张庄矿高压辊磨机辊套疲劳断裂严重、对辊精度不能满足生产要求等问题，马钢重机公司根据张庄矿实际生产要求对对辊进行国产化，国产化内容包括辊轴、辊套等零部件的新制以及装配工艺攻关，通过技术研发同时结合实际生产经验，成功对高压辊磨机辊套与辊轴以及辊轴与轴承进行装配，完成了张庄矿高压辊磨机整对对辊的国产化，为该型设备后续生产及优化提供了理论和实践参考依据。     

构皮滩水电站泄洪洞优化设计

构皮滩水电站为满足2008年12月工程提前发电的需要,结合现有泄洪洞地质情况和施工情况对泄洪洞布置进行了专题研究,结果表明利用降低进口高程为550 m的泄洪洞和坝身放空底孔联合参与后期导流,可缓解2007年导流隧洞下闸封堵后大坝在2008年汛期施工的压力,为大坝施工增加了2个月左右的工期。     

移动通信系统中功率控制研究

在阐述功率控制在移动通信系统中的发展过程的基础上，着重研究了WCDMA系统的功率控制，最后对功率控制未来的研究方向做了简要的分析。     

变频电子阻垢技术的工业应用

中国大唐发电有限责任公司徐塘分公司利用变频电磁阻垢技术在4号发电机组循环冷却水系统进行了成功应用.从理论上比较了物理法与化学法水处理技术的差异.工业应用结果表明,变频电磁技术不仅阻垢效果明显,而且具有安装维护简便,适应性广,运行费用低,对水体无污染等特点.可以替代化学阻垢法.     

醇解技术在制备皮革加脂剂方面的研究进展

本文介绍了醇解反应的动力学、影响醇解反应收率的因素以及醇解反应在合成加脂剂方面的应用。     

复合流场上吸罩流场理论分析

提出在计算复合流场内存在两种不同流态的流动:势流和紊流。针对两种流动,分别建立了其数学模型,对于紊流流场,针对标准k-ε紊流模型的缺陷,采用了RNGk-ε紊流模型使紊流控制方程封闭。以及提出了边界条件的确定原则。为复合流场的数值计算提供了理论指导。