Fluoride catalysis at 175°C. of the reaction: Glycerol plus fatty acid

1. In uncatalyzed reactions the esterification of stearic, oleic, and linolenic acid proceeded at the same general rate though the speed was somewhat enhanced as the degree of unsaturation of the fatty acid increased. None of the reactions went to completion, after 15 hours being 72%, 83%, and 84%, respectively, completed. Only a small fraction of the distearate was converted to the triglyceride; a greater amount of the dioleate was esterified to the trioleate and about half the dilinolenate was changed to the trilinolenate.
2. Of 15 metallic fluorides studied, all afforded some catalysis, but only antimony trifluoride and zinc and cobalt fluorides were outstanding. Antimony trifluoride was the most active although in large amount it caused severe decomposition and charring of the products. Zinc fluoride had the best general properties, approaching antimony trifluoride yet causing practically no decomposition even in high concentration. Its activity was enhanced with an increase in amount, the best concentration apparently being 0.1 mole per 100 grams fatty acid. Antimony trifluoride was also better in larger amount within limits, but cobalt fluoride did not exhibit this property.
3. With zinc fluoride as catalyst the reactions of stearic, oleic and linolenic acids after 15 hours were 95%, 94%, and 92%, respectively, completed. At least three-fourths of the diglycerides were converted to triglycerides. From a study of reaction velocities, zinc fluoride caused the monoglyceride to form at a rate approximately four times that of the uncatalyzed reaction and the diglyceride at a six-fold rate. The triglyceride was formed at an almost undiminished rate whereas in the uncatalyzed reaction the formation of triglyceride was diminished rapidly.
4. Unsaturation and viscosity were not affected seriously in the presence of the fluorides except antimony trifluoride. Certain other fluorides caused severe darkening but without accompanying serious decomposition.

     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

Evaluating the mixing performance of a ribbon blender

This paper investigates the effects of processing and equipment parameters of a ribbon blender (i.e. loading method of lubricant, fill level, blade speed and blade design) on magnesium stearate homogeneity. A core sampling technique is used to obtain at least one hundred samples per sampling event, which are extracted throughout the blender and yield a thorough characterization of the entire bed. The results presented here can be used as a guideline to develop appropriate blending processes and characterization protocols for ribbon blenders.     

DESIGN AND IMPLEMENTATION OF STATE OBSERVERS IN REACTIVE DISTILLATION

This study demonstrates that state observers can be developed and applied to infer the composition profiles of reactive distillation columns from noise-contaminated temperature measurements. The design and implementation of a Kalman filter (KF) and a Luenberger observer (LO) are carried out, and their performances are quantitatively assessed. The reliability, accuracy, and robustness of the two designs method are examined and compared quantitatively. The design and implementation of a Luenberger observer are simpler and easier to carry out than those of a Kalman filter. On the other hand, a Kalman filter is found to be more robust to a noisy measurements, erroneous initial estimates, and model uncertainties. A Luenberger observer could be used for composition estimation of reactive distillation when an ideal model of the system can reasonably approximate the real system; otherwise, a Kalman filter is recommended to be applied in more practical situations.     

X-ray topography studies of dislocations in single crystal CVD diamond

X-ray topography has been used to study single crystal diamond samples homoepitaxially grown by microwave plasma-assisted chemical vapour deposition (CVD) on high pressure high temperature (HPHT) and CVD synthetic diamond substrates. Clusters of dislocations in the CVD diamond layers emanated from points at or near the interface with the substrate. The Burgers vectors of observed dislocations have been determined from sets of {111} projection topographs. Dislocations have line directions close to the [001] growth direction and are either edge or 45° mixed dislocations. Where groups of dislocations originated at isolated points they tended to be of the edge variety. Where the substrate surface was deliberately damaged before growth, two sets of dislocations were observed to have propagated from each line of damage and there was a tendency for dislocations to be of the 45° mixed variety with a component of their Burgers vector parallel to the polishing direction. It is demonstrated that X-ray topography can be used to deduce the growth history of CVD synthetic diamond samples produced in multiple growth stages.     

Drying Kinetics of a Porous Spherical Particle and the Inversion Temperature

A model is presented for drying of a single porous particle with superheated steam and humid air. Experimental data for spherical porous ceramic particle reported in the literature were used for the validation of the model. An inversion temperature at which the evaporation rates within superheated steam and humid air are equal was predicted. The effect of thermophysical properties of the particle (permeability 10^-14 - 10^-17 m², diameter 3 × 10^-3 - 10 × 10^-3 m) and operating variables (gas mass flux 0.26 - 0.78 kg m^-2 s^-1, drying agent temperature 120-200°C) is tested. The inversion temperature is shown to be affected by the thermophysical properties of the porous particle and of the drying agent.     

Undergraduate software engineering education: the mark of a discipline

Undergraduate software engineering education is now well established in many countries, and many of these degree programs have received formal accreditation by the relevant country's professional body for computing. SE 2004 represents an enormous effort by numerous individuals across the discipline. Its quality has been clearly recognized by the sponsoring organizations. The developmental team confidently looks forward to the volume's use and to your participation in future evaluations and in the next phase of development. The volume provides usable results for those in emerging economies who wish to enter the software engineering community, and we know that individual project members and the participating national bodies are ready to assist.     

The effect of ambient temperature on the sensitivity of hot-cathode ionization gauges

We measured the sensitivities of five hot-cathode ionization gauges for ambient laboratory temperatures between 23 and 31 °C. All of the ionization gauges exhibited very similar behavior, and the sensitivity could be adequately modeled with a linear function of temperature. The slopes of the fits were smaller than one would expect due to changes in the calibration chamber number density. The thermal transpiration effect, due to local heating of the gauge structures, can account for this, and a characteristic gauge tube temperature can be inferred from the temperature dependence of the sensitivity. A recent comparison of the high vacuum standards of several National Metrology Institutes (NMIs) was performed over the range of 10⁻⁶-10⁻³ Pa using hot-cathode and spinning rotor gauges as transfer standards. Among the participants, laboratory temperatures varied by as much as 5 °C. It is necessary to know how laboratory temperature affects the sensitivity of the hot-cathode transfer standards (spinning rotor gauges explicitly account for the gas temperature) so that individual laboratory results can be corrected to a common temperature.     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

Experimental determination of NH<Subscript>4</Subscript>NO<Subscript>3</Subscript>-KNO<Subscript>3</Subscript> binary phase diagram

The solid-state phase transitions in ammonium nitrate (AN)-potassium nitrate (KN) system, and the equilibrium AN-KN phase diagram have been determined by using differential scanning calorimetry and high-temperature in situ x-ray diffractometry. Sample preparation was performed in a special “dry room” with very low humidity. A single phase region (AN III) with no phase transitions to 373 K was observed in the composition range 5 to 20% KN; this is critical for use in air bag gas generators. The high-temperature KN phase (KN I) has a wide range of stability from 20 to 100 wt.% KN. There are one eutectic, two eutectoid, three peritectoid, and one congruent transformations in this phase diagram. Two new nonstoichiometric phases were found at lower temperatures in the mid-composition range between the AN and KN terminal solid solutions. Details of the phase equilibria are presented.