Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

分割电极片状压电致动器——(二)位移特性及狭缝宽度对其影响的实验研究

研究了悬臂梁式分割电极片状压电致动器的位移特性。理论分析表明，分割电极狭缝宽度会减小致动器自由端的位移输出，但当狭缝宽度小于致动器电极宽度的１０％时，可忽略狭缝宽度的影响。致动器端部位移的测试结果大于理论计算值。与现有磁头悬浮臂尺寸相近的致动器，在２０Ｖ～５０Ｖ的电压驱动下均可获得１μｍ～２μｍ的致动位移。对９８５０道／厘米的密度磁盘，该位移能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器位移的基本要求。     

Acoustical tomography based on the second-order Born transformperturbation approximation

Reconstruction algorithms and their numerical examples of acoustical tomography based on the second-order Born transform perturbation approximation are presented. The reconstruction algorithms in the second-order Born approximation are similar in form to those in the first-order Born approximation. Replacing the angular spectrum of the scattered wave in the first-order case by the result of applying a first-order operator to the angular spectrum of the scattered wave or applying a second-order operator to the angular spectrum of the incident wave leads to the second-order reconstruction algorithms. Also, comparisons of reconstruction algorithms of the first- and second-order Born approximations are given, and they show that the second-order Born approximation algorithms have a distinct advantage over the first-order approximations in many cases     

A hybrid wafer-dicing process for GaAs MMIC production

A dicing process for GaAs MMIC (monolithic microwave integrated circuit) wafers using spin-on wax for wafer mounting and a hybrid process of wet chemical etching/mechanical sawing for chip dicing is described. This process minimizes ragged chip edges and reduces generation of microcracks in addition to the elimination of the plated gold burrs on the backside of the diced MMIC chips. This process gives a uniformity of -3 μm across a 2-in wafer following the completion of the whole backside process. This GaAs chip dicing technique is amenable to production because it exhibits both a very high chip yield (>90%) and nearly flawless edges     

Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

Pore size control of porous silica by sol-gel process

Porous silica glass was prepared by sol-gel process from tetraethoxysilane (TEOS). The effects of solvents (water, ethanol), drying condition, heat treatment temperature on specific surface area and pore size distribution of porous silica were investigated. Gelation process accelerates with an increase of H₂O content, while retards with the increase of ethanol amount. Structure changes during heat treatment were studied by means of DTA, XRD. TEM micrographs show that the gel particles shrink after heated at 500°C, thus the average pore size decreases.     

Differences in risk factors for being either a hepatitis B carrier or anti-hepatitis C+ in a hepatoma-hyperendemic area in rural Taiwan

This is a study of the differences in the risk factors for being either hepatitis B surface antigen positive [HBsAg(+)] or antibody to hepatitis C virus positive [Anti-HCV(+)] in A-Lein, a rural area in southern Taiwan, an area which also has a high hepatoma mortality rate. Three hundred eighty-five patients age > or =40 years participated in hepatoma screening at the A-Lein Community Health Center during 1995. Those who were HBsAg(-) and anti-HCV(-) or had coinfection of HBsAg(+) and anti-HCV(+) were excluded, leaving 293 patients: 109 HBsAg(+) and 184 anti-HCV(+). The anti-HCV(+) patients had a lower socioeconomic status (as defined by level of education and type of occupation) and were older than HBsAg(+) patients (P < 0.05). Those with higher alanine aminotransferase levels (ALT) also had a higher anti-HCV(+) to HBsAg(+) odds ratio (OR), and a dose response relationship was found, P < 0.0001. Anti-HCV(+) patients were more likely than HBsAg(+) patients to have a spouse who shared the infection, OR = 5.11; 95% CI, 2.30-11.28. Anti-HCV(+) patients were more likely than HBsAg(+) patients to have had blood transfusions (OR = 2.66; 95% CI, 1.20-5.89), frequent medical injections (OR = 2.64; 95% CI, 1.62-4.31), or injections by non-licensed medical providers (OR = 1.91; 95% CI, 1.18-3.09). Multiple logistic regression analysis showed that the significant factors for anti-HCV(+) patients vs. HBsAg(+) patients are drinking habit (OR = 3.45; 95% CI, 1.02-11.60), age (OR = 6.33; 95% CI, 2.93-13.68), and frequent medical injections (OR = 2.88; 95% CI, 1.65-5.03). The transmission of hepatitis C in A-Lein is closely related to low socioeconomic status, age, alcohol abuse, spouses being anti-HCV(+), and frequent medical injections, especially from non-licensed medical providers, including both pharmacists and those with no medical licensing whatsoever. These nonlicensed medical providers sometimes reuse needles to save money, which is a likely route of infection.     

Onset of gas self-induction and power consumption after gas induction in an agitated tank

The behavior of inducted gas from liquid surface and the; power requirements in an agitated tank using a mechanical agitator are studied in order to increase the amount of gas self-induction and the gas retention time for gas absorption. A 45° six-blade downward impeller turbine was utilized in this study. Air and water, air and 40 wt% 60 wt%, and 80 wt% of glycerin water, and air and 106 cP silicon oil were employed as gas and liquid phases. Variables which were studied included geometrical factors (immersed depth of impeller, baffle with and diameter of impeller) and the physical properties of the liquid (viscosity, density, and surface tension). The correlations for the onset speed of impeller and power consumption after gas induction in the agitated tank are established from our experimental results. The amount of gas self-induction from the liquid surface in the agitated tank increases with increasing impeller diameter and speed and decreases with increasing baffle width, depth of impeller and viscosity of liquid.     

石蜡光氯化合成氯蜡－70的研究──（Ⅲ）反应过程致色因素考察及生色机理研究

氯蜡－７０是—应用广泛、性能优良的精细化工产品，其色泽是—重要的技术指标，直接影响着产品的质量和应用。本文考察了合成反应过程导致生色的因素，指出原料中含有的少量环烷烃、芳烃、杂环有机物及少量无机杂质能影响产品的色泽，实验表明温度过高，光源波长选择不当也是致色的重要原因。研究了致色的过程，提出其生色历程是按照β－消除反应机理进行的，并做了具体描述。     

A study on the anodic protection of Titanium evaporators in Al2(SO4)3 solution

The feasibility of the anodic protection of titanium evaporators in Al₂(SO₄)₃ solution was studied by the measurement of polarization curves, weight loss, solubility of passive film and AC impedance. The protection parameters and efficiency were determined. In addition, the practical technology of anodic protection was studied by screening reference electrodes and auxiliary cathodes. Throwing power was also measured. Four rows of tube-type evaporators of titanium have been anodically protected in situ. Field tests lasting more than one year show satisfactory results.