Substrate-connected high voltage pumping circuits for low supplyvoltages

Novel high voltage pumping circuits for low supply voltages are proposed. Utilising a small pumping circuit and the new substrate-connected techniques can enhance charge transfer efficiency and eliminate the body effect at low supply voltages. Furthermore, a diode-connected transistor technique can improve the reverse charge sharing phenomenon when the output has a load current. With this technique high boosted voltages can be obtained at low supply voltages     

Highly compact AC-AC converter achieving a high voltage transferratio

This paper reports a new, highly integrated modular design approach for pulsewidth-modulation AC-AC converters based on a modular phase-bank structure. Novel high-power 3-in-1 integrated bi-directional power modules (IBPM) rated at 1200-V AC and 150 A and the 3-to-1 phase bank circuits have been successfully developed, fabricated and tested. This enables the modularity design of the multiphase converter systems and reduces the critical parasitic inductance. A theoretical analysis of the IBPM's silicon utilization for this new breed of direct power converters has been outlined. A lab prototype at medium power level has been successfully designed, implemented, and tested with good results. A nearly 460-VRMS out voltage at a 1:0.955 voltage transfer ratio, which, perhaps, is the highest performance reported so far in the literature, has been achieved by the novel two-side modulation control system. The converter-fed AC motor system is able to operate over the 0-240 Hz range with inherent regenerative capability and four-quadrant operation. Potential industrial applications are also briefly highlighted in this paper     

A theoretical study of pulsed laser sampling photon amplifiers

Theoretical studies point to significant improvements in the performance of semiconductor laser amplifiers by injecting carriers with pulsed electric currents of sub-nanosecond duration. A pulsed Fabry-Perot amplifier (FPA) is most sensitive to input lightwave at the instant the carrier density is crossing the critical region, and gives a sharply pulsed sampling effect on the input lightwave signal. Compared with a FPA operating at subcritical electron density, the pulsed amplifier gives much higher gain, peak power, and bandwidth. In fact, pulsed operation of a FPA is also expected to give significantly higher gain and about the same peak output power as a traveling wave amplifier. Pulsed operation also improves the performance of a traveling wave amplifier by attenuating its internally reflected waves     

Effects of free convection and mass transfer on the flow past an impulsively moving infinite vertical circular cylinder

The effects of free convection and mass transfer are taken into account for the Stokes' problem of the flow near an impulsively moving infinite vertical circular cylinder. Expressions of the velocity, temperature, concentration and skin friction of the fluid in closed form are obtained by the Laplace transform technique. The results based on various values of the parameters Gr (Grashof number), Gm (modified Grashof number), Sc (Schmidt number) and Pr (Prandtl number) are given in graphical form. It will be seen that there is a rise in the velocity due to the presence of a foreign mass. But higher Sc yields the lower velocity and skin friction. As the radius of the circular cylinder approaches to infinite, the results presented in this paper agree with those of V.M. Soundalgekar's and C.K. Chen's etc. for the flow past an impulsively moving infinite vertical plate.     

China Likely to Resume Oil Futures Soon

China is likely to resume operation of its oil futures this year, according to reports from the media about a futures conference organized by the Shanghai Futures Exchange (SHFE) in late May. "As China has become an important oil producer and consumer,the demand for our own oil futures market emerges,which will help China oil-related enterprises hedge risks," said Li Ruisheng, vice president of PetroChina's refining and marketing company.     

Direct analysis of transient stability: Experience with the Taipower system

A direct method for transient stability analysis of a multimachine power system is presented. Emphasis is placed on the detailed development and evaluation of the proposed method in transient stability assessment. An energy-type Lyapunov function, taking into account the effect of transfer conductance, is introduced first. The potential energy boundary surface method is then adopted to determine the critical energy value quickly. The main computational burden in the direct method lies in the reduction of the admittance matrices. In this paper, an efficient reduction technique incorporating the sparsity technique and compensation theory is developed. Finally, the proposed method was tested on the Taipower system, which is the only power system in Taiwan. The results obtained confirm the validity and accuracy of the proposed method, and hence demonstrate the superiority and potential of the direct method in real power system applications.     

Integration of mobile vehicles for automated material handlingusing Profibus and IEEE 802.11 networks

This paper focuses on a method to integrate mobile devices such as a mobile robot, automated guided vehicle, and unmanned container transporter to form an automated material handling system. In this paper, the stationary devices are connected via a Profibus network while the mobile devices are communicating via an IEEE 802.11 wireless LAN. In order to integrate these two networks, a protocol converter is developed on a PC platform that runs two interacting processes with shared internal buffers. The protocol converter performs a role of translator between two different protocols by converting the format of a data frame. In addition to this basic conversion function, the protocol converter has a virtual polling algorithm to reduce the uncertainty involved in accessing the wireless network. Finally, the integrated network. of Profibus and IEEE 802.11 is experimentally evaluated for its data latency and throughput, which shows the feasibility of the Profibus-IEEE 802.11 network for industrial applications involving mobile devices     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

Modeling Temperature in Coupled Electrical and Thermal Simulations of the Electroconsolidation® Process

Electroconsolidation® is a process for densifying complex-shaped parts by using electrically conductive particulate solids as a pressure-transmitting medium. The part is immersed in a bed of the particulate medium contained in a die chamber. Sintering temperature is achieved by resistive heating of the medium while applying compaction pressure. The process is capable of ultrahigh temperatures and short cycle times and offers the potential for low processing costs.

Control of the process and selection of process conditions require knowledge of the temperatures within the die. Temperature gradients exist because of the high heating rate and because of variations of density and electrical resistivity of the medium due to the presence of the part. Direct measurement of temperature with thermocouples or other conventional means is impractical because of the high temperatures, high currents, and high pressures that are involved. Therefore, a computer model was developed to predict temperature as a function of time and applied voltage for any location in the die. The computer model is composed of three parts: a geometrical model to approximate the density and resistivity variations in the medium, a finite-element model to calculate the rate of resistive heating within each element, and a finite-difference model to calculate the temperature distribution based on solution of the heat-transfer equations. Predicted temperatures have been shown to be in excellent agreement with measurements, and numerical simulation provided encouraging consistency and reasonably accurate predictions of temperature profiles within the die. The model demonstrated the feasibility of a new process to achieve simultaneous application of pressure and heat to powder densification in Electroconsolidation.     

The Effect of Run Time on the Inter-Unit Uniformity of Aqueous Film Coating Applied to Glass Beads in a Hi-Coater

Coating experiments were conducted to assess the inter-unit uniformity using individual weight gains of glass beads. Applying more aqueous film coating and prolonging the film-coating process by diluting the coating suspension did improve the coating variability among glass beads. It appears that run time is an important underlying factor which affecting the inter-unit coating uniformity.