Hot carrier analysis in low-temperature poly-Si thin-film transistors using pico-second time-resolved emission microscope

We have analyzed degradation of N-channel thin-film-transistor (TFT) under dynamic stress using a pico-second time-resolved emission microscope. We have successfully detected emission at pulse fall edge for the first time. Emission intensity increased with the decrease of pulse fall time. As the degradation depended on the pulse fall time, this dependence clearly illustrates that hot electrons are the dominant cause of the degradation under dynamic stress. Based on these dependences, we proposed a model considering electron traps in the poly-Si.     

SiGe VCOs operating up to 88 GHz, suitable for automotive radar sensors

VCOs fully integrated in an SiGe preproduction technology are presented. By cutting interconnection lines a wide frequency range can be covered, up to 88.4 GHz. Special effort has been made to meet the demands for 77 GHz automotive radar. In the corresponding tuning range from 75.3 to 79.6 GHz, an output power of about 11 dBm (with -2.2 dBm potential measurement uncertainty) was achieved for each of the two complementary outputs, i.e. in total 14 dBm. The phase noise is about -94 dBc/Hz at 1 MHz offset frequency.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

On the synergy between electrical and photonic switching

This article focuses on the values of electrical switching vs. photonic switching in the context of telecom transport networks. In particular, we show that the requirement of providing agility at the optical layer in the face of traffic forecast uncertainties is served better through photonic switching. On the other hand, some of the network-level functions, such as fast protection, subwavelength aggregation, and flexible client connectivity, require electrical switching. We further argue that additional values are achieved with hybrid photonic and electrical switching, which do not exist when either of these options is used in isolation.     

An adaptive p-persistent MAC scheme for multimedia WLAN

The letter proposes an adaptive p-persistent-based (APP) medium access control (MAC) scheme for the IEEE 802.11e distributed WLAN supporting multimedia services. The APP MAC scheme adaptively gives differentiated permission probabilities to transmission stations which are in different access category and with various waiting delay. Simulation results show that the APP MAC scheme can improve the performance of multimedia WLAN, such as small voice packet dropping probability, low delay variation, and high system throughput, compared to conventional MAC algorithms     

Bandpass filters with reconfigurable transmission zeros using varactor-tuned tapped stubs

In this letter, bandpass filters with one or two tunable transmission zeros are proposed. The reconfigurable transmission zeros are implemented through varactors in combination with tapped quarter-wavelength stubs. Based on mixed mode simulations including EM simulation and circuit simulation, the proposed filters were designed and fabricated on low-cost FR4 board. The measurement results verified the design concepts.     

Towards intelligent dressing

The aim of this article is to state the principles of an intelligent monitoring and control system for the grinding machine, comprising the dressing process as well as grinding stability.     

Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.